[U-Boot] [PATCH] drivers: mmc: omap_hsmmc: Fix IO Buffer on OMAP36xx

Jaehoon Chung jh80.chung at samsung.com
Thu Feb 9 05:26:49 UTC 2017


Hi

On 02/07/2017 02:31 AM, aford173 at gmail.com wrote:
> From: Adam Ford <aford173 at gmail.com>
> 
> On the OMAP36xx/37xx the CONTROL_WKUP_CTRL register has
> a field (bit 6) named GPIO_IO_PWRDNZ.  If 0, the IO buffers which
> are related to GPIO_126, 127 and 129 are disabled. Some boards may
> need this for MMC. After the PBIAS is configured, this bit should
> be set high to enable these GPIO pins.
> 
> Signed-off-by: Adam Ford <aford173 at gmail.com>

Applied on u-boot-mmc. Thanks!

Best Regards,
Jaehoon Chung

> 
> ---
> V4:  Fixed some spacing and remove a warning when compiling on board
>      not using the new #define CONFIG_MMC_OMAP36XX_PINS
> V3:  The OMAP36xx datasheet states to clear this bit before changing
>      PBIAS, so this update clears the bit before changing it.  This
>      patch also makes the option dependant on MMC_OMAP_HS.
> V2:  Make this feature a config option and add it to the MMC section
>      of the Kconfig.  This allows the precompiler to only include it
>      in a small handfull of OMAP36XX and 37XX boards using MMC1.
> 
> diff --git a/configs/omap3_logic_defconfig b/configs/omap3_logic_defconfig
> index f200e87..37ee267 100644
> --- a/configs/omap3_logic_defconfig
> +++ b/configs/omap3_logic_defconfig
> @@ -33,6 +33,7 @@ CONFIG_CMD_UBI=y
>  CONFIG_ISO_PARTITION=y
>  CONFIG_EFI_PARTITION=y
>  CONFIG_MMC_OMAP_HS=y
> +CONFIG_MMC_OMAP36XX_PINS=y
>  CONFIG_SYS_NS16550=y
>  CONFIG_USB=y
>  CONFIG_USB_MUSB_GADGET=y
> diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
> index 0c07781..01d1dbf 100644
> --- a/drivers/mmc/Kconfig
> +++ b/drivers/mmc/Kconfig
> @@ -131,6 +131,18 @@ config MMC_OMAP_HS
>  
>  	  If unsure, say N.
>  
> +config MMC_OMAP36XX_PINS
> +	bool "Enable MMC1 on OMAP36xx/37xx"
> +	depends on OMAP34XX && MMC_OMAP_HS
> +	help
> +	  This enables extended-drain in the MMC/SD/SDIO1I/O and
> +	  GPIO-associated I/O cells (gpio_126, gpio_127, and gpio_129)
> +	  specific to the OMAP36xx/37xx using MMC1
> +
> +	  If you have a controller with this interface, say Y here.
> +
> +	  If unsure, say N.
> +
>  config SH_SDHI
>  	bool "SuperH/Renesas ARM SoCs on-chip SDHI host controller support"
>  	depends on RMOBILE
> diff --git a/drivers/mmc/omap_hsmmc.c b/drivers/mmc/omap_hsmmc.c
> index b326846..07ab9d7 100644
> --- a/drivers/mmc/omap_hsmmc.c
> +++ b/drivers/mmc/omap_hsmmc.c
> @@ -38,6 +38,7 @@
>  #include <asm/arch/sys_proto.h>
>  #endif
>  #include <dm.h>
> +#include <asm/arch-omap3/mux.h>
>  
>  DECLARE_GLOBAL_DATA_PTR;
>  
> @@ -102,6 +103,9 @@ static unsigned char mmc_board_init(struct mmc *mmc)
>  	t2_t *t2_base = (t2_t *)T2_BASE;
>  	struct prcm *prcm_base = (struct prcm *)PRCM_BASE;
>  	u32 pbias_lite;
> +#ifdef CONFIG_MMC_OMAP36XX_PINS
> +	u32 wkup_ctrl = readl(OMAP34XX_CTRL_WKUP_CTRL);
> +#endif
>  
>  	pbias_lite = readl(&t2_base->pbias_lite);
>  	pbias_lite &= ~(PBIASLITEPWRDNZ1 | PBIASLITEPWRDNZ0);
> @@ -109,12 +113,26 @@ static unsigned char mmc_board_init(struct mmc *mmc)
>  	/* for cairo board, we need to set up 1.8 Volt bias level on MMC1 */
>  	pbias_lite &= ~PBIASLITEVMODE0;
>  #endif
> +#ifdef CONFIG_MMC_OMAP36XX_PINS
> +	if (get_cpu_family() == CPU_OMAP36XX) {
> +		/* Disable extended drain IO before changing PBIAS */
> +		wkup_ctrl &= ~OMAP34XX_CTRL_WKUP_CTRL_GPIO_IO_PWRDNZ;
> +		writel(wkup_ctrl, OMAP34XX_CTRL_WKUP_CTRL);
> +	}
> +#endif
>  	writel(pbias_lite, &t2_base->pbias_lite);
>  
>  	writel(pbias_lite | PBIASLITEPWRDNZ1 |
>  		PBIASSPEEDCTRL0 | PBIASLITEPWRDNZ0,
>  		&t2_base->pbias_lite);
>  
> +#ifdef CONFIG_MMC_OMAP36XX_PINS
> +	if (get_cpu_family() == CPU_OMAP36XX)
> +		/* Enable extended drain IO after changing PBIAS */
> +		writel(wkup_ctrl |
> +				OMAP34XX_CTRL_WKUP_CTRL_GPIO_IO_PWRDNZ,
> +				OMAP34XX_CTRL_WKUP_CTRL);
> +#endif
>  	writel(readl(&t2_base->devconf0) | MMCSDIO1ADPCLKISEL,
>  		&t2_base->devconf0);
>  
> 



More information about the U-Boot mailing list