[U-Boot] [PATCH v3 1/3] sunxi: add basic V3s support

Icenowy Zheng icenowy at aosc.xyz
Sat Feb 11 11:11:00 UTC 2017


Basic U-Boot support is now present for V3s.

Some memory addresses are changed specially for V3s, as the original
address map cannot fit into a so small DRAM.

As the DRAM controller code needs a big refactor, the SPL support is
disabled in this version.

Signed-off-by: Icenowy Zheng <icenowy at aosc.xyz>
---
Changes in v3:
- removed some dead code about DFU and video.

 arch/arm/include/asm/arch-sunxi/gpio.h |  1 +
 arch/arm/mach-sunxi/board.c            |  4 ++++
 arch/arm/mach-sunxi/cpu_info.c         |  2 ++
 board/sunxi/Kconfig                    | 14 ++++++++++++--
 include/configs/sun8i.h                |  2 ++
 include/configs/sunxi-common.h         | 30 +++++++++++++++++++++++++++---
 6 files changed, 48 insertions(+), 5 deletions(-)

diff --git a/arch/arm/include/asm/arch-sunxi/gpio.h b/arch/arm/include/asm/arch-sunxi/gpio.h
index 85a4ec3b0e..24f85206c8 100644
--- a/arch/arm/include/asm/arch-sunxi/gpio.h
+++ b/arch/arm/include/asm/arch-sunxi/gpio.h
@@ -161,6 +161,7 @@ enum sunxi_gpio_number {
 #define SUN8I_GPB_UART2		2
 #define SUN8I_A33_GPB_UART0	3
 #define SUN8I_A83T_GPB_UART0	2
+#define SUN8I_V3S_GPB_UART0	3
 #define SUN50I_GPB_UART0	4
 
 #define SUNXI_GPC_NAND		2
diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c
index 52be5b0551..90b3b94e51 100644
--- a/arch/arm/mach-sunxi/board.c
+++ b/arch/arm/mach-sunxi/board.c
@@ -110,6 +110,10 @@ static int gpio_init(void)
 	sunxi_gpio_set_cfgpin(SUNXI_GPB(9), SUN8I_A83T_GPB_UART0);
 	sunxi_gpio_set_cfgpin(SUNXI_GPB(10), SUN8I_A83T_GPB_UART0);
 	sunxi_gpio_set_pull(SUNXI_GPB(10), SUNXI_GPIO_PULL_UP);
+#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN8I_V3S)
+	sunxi_gpio_set_cfgpin(SUNXI_GPB(8), SUN8I_V3S_GPB_UART0);
+	sunxi_gpio_set_cfgpin(SUNXI_GPB(9), SUN8I_V3S_GPB_UART0);
+	sunxi_gpio_set_pull(SUNXI_GPB(9), SUNXI_GPIO_PULL_UP);
 #elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN9I)
 	sunxi_gpio_set_cfgpin(SUNXI_GPH(12), SUN9I_GPH_UART0);
 	sunxi_gpio_set_cfgpin(SUNXI_GPH(13), SUN9I_GPH_UART0);
diff --git a/arch/arm/mach-sunxi/cpu_info.c b/arch/arm/mach-sunxi/cpu_info.c
index f1f6fd5ba4..15f1e0e45a 100644
--- a/arch/arm/mach-sunxi/cpu_info.c
+++ b/arch/arm/mach-sunxi/cpu_info.c
@@ -87,6 +87,8 @@ int print_cpuinfo(void)
 	printf("CPU:   Allwinner A83T (SUN8I %04x)\n", sunxi_get_sram_id());
 #elif defined CONFIG_MACH_SUN8I_H3
 	printf("CPU:   Allwinner H3 (SUN8I %04x)\n", sunxi_get_sram_id());
+#elif defined CONFIG_MACH_SUN8I_V3S
+	printf("CPU:   Allwinner V3s (SUN8I %04x)\n", sunxi_get_sram_id());
 #elif defined CONFIG_MACH_SUN9I
 	puts("CPU:   Allwinner A80 (SUN9I)\n");
 #elif defined CONFIG_MACH_SUN50I
diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
index 37b42521a4..018bdd12dd 100644
--- a/board/sunxi/Kconfig
+++ b/board/sunxi/Kconfig
@@ -115,6 +115,14 @@ config MACH_SUN8I_H3
 	select SUPPORT_SPL
 	select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
 
+config MACH_SUN8I_V3S
+	bool "sun8i (Allwinner V3s)"
+	select CPU_V7
+	select CPU_V7_HAS_NONSEC
+	select CPU_V7_HAS_VIRT
+	select SUNXI_GEN_SUN6I
+	select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
+
 config MACH_SUN9I
 	bool "sun9i (Allwinner A80)"
 	select CPU_V7
@@ -132,7 +140,8 @@ endchoice
 # The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33"
 config MACH_SUN8I
 	bool
-	default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_H3 || MACH_SUN8I_A83T
+	default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_H3 || \
+		MACH_SUN8I_A83T || MACH_SUN8I_V3S
 
 config RESERVE_ALLWINNER_BOOT0_HEADER
 	bool "reserve space for Allwinner boot0 header"
@@ -485,7 +494,8 @@ config AXP_GPIO
 
 config VIDEO
 	bool "Enable graphical uboot console on HDMI, LCD or VGA"
-	depends on !MACH_SUN8I_A83T && !MACH_SUN8I_H3 && !MACH_SUN9I && !MACH_SUN50I
+	depends on !MACH_SUN8I_A83T && !MACH_SUN8I_H3 && !MACH_SUN8I_V3S && \
+		!MACH_SUN9I && !MACH_SUN50I
 	default y
 	---help---
 	Say Y here to add support for using a cfb console on the HDMI, LCD
diff --git a/include/configs/sun8i.h b/include/configs/sun8i.h
index a4c3fb69e4..6ac42acaea 100644
--- a/include/configs/sun8i.h
+++ b/include/configs/sun8i.h
@@ -21,6 +21,8 @@
 	#define CONFIG_SUNXI_USB_PHYS	4
 #elif defined CONFIG_MACH_SUN8I_A83T
 	#define CONFIG_SUNXI_USB_PHYS	3
+#elif defined CONFIG_MACH_SUN8I_V3S
+	#define CONFIG_SUNXI_USB_PHYS	1
 #else
 	#define CONFIG_SUNXI_USB_PHYS	2
 #endif
diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h
index 3ac96da190..41d47acfd2 100644
--- a/include/configs/sunxi-common.h
+++ b/include/configs/sunxi-common.h
@@ -75,8 +75,13 @@
 #else
 #define SDRAM_OFFSET(x) 0x4##x
 #define CONFIG_SYS_SDRAM_BASE		0x40000000
-#define CONFIG_SYS_LOAD_ADDR		0x42000000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR		0x41000000 /* default load address */
+/* V3s do not have enough memory to place code at 0x4a000000 */
+#ifndef CONFIG_MACH_SUN8I_V3S
 #define CONFIG_SYS_TEXT_BASE		0x4a000000
+#else
+#define CONFIG_SYS_TEXT_BASE		0x42e00000
+#endif
 /* Note SPL_STACK_R_ADDR is set through Kconfig, we include it here 
  * since it needs to fit in with the other values. By also #defining it
  * we get warnings if the Kconfig value mismatches. */
@@ -147,8 +152,13 @@
 #define CONFIG_SYS_MMC_MAX_DEVICE	4
 #endif
 
+#ifndef CONFIG_MACH_SUN8I_V3S
 /* 64MB of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (64 << 20))
+#else
+/* 2MB of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (2 << 20))
+#endif
 
 /*
  * Miscellaneous configurable options
@@ -383,16 +393,30 @@ extern int soft_i2c_gpio_scl;
  * 32M uncompressed kernel, 16M compressed kernel, 1M fdt,
  * 1M script, 1M pxe and the ramdisk at the end.
  */
-
+#ifndef CONFIG_MACH_SUN8I_V3S
+#define BOOTM_SIZE     __stringify(0xa000000)
 #define KERNEL_ADDR_R  __stringify(SDRAM_OFFSET(2000000))
 #define FDT_ADDR_R     __stringify(SDRAM_OFFSET(3000000))
 #define SCRIPT_ADDR_R  __stringify(SDRAM_OFFSET(3100000))
 #define PXEFILE_ADDR_R __stringify(SDRAM_OFFSET(3200000))
 #define RAMDISK_ADDR_R __stringify(SDRAM_OFFSET(3300000))
+#else
+/*
+ * 64M RAM minus 2MB heap + 16MB for u-boot, stack, fb, etc.
+ * 16M uncompressed kernel, 8M compressed kernel, 1M fdt,
+ * 1M script, 1M pxe and the ramdisk at the end.
+ */
+#define BOOTM_SIZE     __stringify(0x2e00000)
+#define KERNEL_ADDR_R  __stringify(SDRAM_OFFSET(1000000))
+#define FDT_ADDR_R     __stringify(SDRAM_OFFSET(1800000))
+#define SCRIPT_ADDR_R  __stringify(SDRAM_OFFSET(1900000))
+#define PXEFILE_ADDR_R __stringify(SDRAM_OFFSET(1A00000))
+#define RAMDISK_ADDR_R __stringify(SDRAM_OFFSET(1B00000))
+#endif
 #endif
 
 #define MEM_LAYOUT_ENV_SETTINGS \
-	"bootm_size=0xa000000\0" \
+	"bootm_size=" BOOTM_SIZE "\0" \
 	"kernel_addr_r=" KERNEL_ADDR_R "\0" \
 	"fdt_addr_r=" FDT_ADDR_R "\0" \
 	"scriptaddr=" SCRIPT_ADDR_R "\0" \
-- 
2.11.0



More information about the U-Boot mailing list