[U-Boot] [PATCH 3/3] armv8: ls1088aqds: Add support of LS1088AQDS

Ashish Kumar Ashish.Kumar at nxp.com
Wed Feb 15 15:14:09 UTC 2017


This patch add support of LS1088AQDS platform.

The LS1088A QorIQTM Development System (QDS) is a
high-performance computing, evaluation, and
development platform that supports the LS1088A QorIQ Architecture
processor.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha at nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar at nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie at nxp.com>
---
 arch/arm/Kconfig                                   |  11 +
 arch/arm/cpu/armv8/Kconfig                         |   2 +-
 arch/arm/cpu/armv8/fsl-layerscape/Kconfig          |  21 +
 arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c |   2 +
 arch/arm/cpu/armv8/fsl-layerscape/soc.c            |   1 +
 arch/arm/dts/Makefile                              |   1 +
 arch/arm/dts/fsl-ls1088a-qds.dts                   |  70 +++
 board/freescale/ls1088a/Kconfig                    |  16 +
 board/freescale/ls1088a/MAINTAINERS                |  10 +-
 board/freescale/ls1088a/Makefile                   |   1 +
 board/freescale/ls1088a/ddr.c                      | 119 +---
 board/freescale/ls1088a/ddr.h                      |   9 +-
 board/freescale/ls1088a/eth_ls1088aqds.c           | 650 +++++++++++++++++++++
 board/freescale/ls1088a/ls1088a.c                  | 106 +++-
 board/freescale/ls1088a/ls1088a_qixis.h            |   5 +
 configs/ls1088aqds_qspi_defconfig                  |  27 +
 configs/ls1088ardb_qspi_defconfig                  |   6 -
 include/configs/ls1088a_common.h                   |   8 +-
 include/configs/ls1088aqds.h                       | 403 +++++++++++++
 19 files changed, 1321 insertions(+), 147 deletions(-)
 create mode 100644 arch/arm/dts/fsl-ls1088a-qds.dts
 create mode 100644 board/freescale/ls1088a/eth_ls1088aqds.c
 create mode 100644 configs/ls1088aqds_qspi_defconfig
 create mode 100644 include/configs/ls1088aqds.h

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 0c63dfe..435a8f8 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -776,6 +776,17 @@ config TARGET_LS2080A_SIMU
 	  development platform that supports the QorIQ LS2080A
 	  Layerscape Architecture processor.
 
+config TARGET_LS1088AQDS
+	bool "Support ls1088aqds"
+	select ARCH_LS1088A
+	select ARM64
+	select ARMV8_MULTIENTRY
+	help
+	  Support for NXP LS1088AQDS platform
+	  The LS1088A Development System (QDS) is a high-performance
+	  development platform that supports the QorIQ LS1088A
+	  Layerscape Architecture processor.
+
 config TARGET_LS2080AQDS
 	bool "Support ls2080aqds"
 	select ARCH_LS2080A
diff --git a/arch/arm/cpu/armv8/Kconfig b/arch/arm/cpu/armv8/Kconfig
index 630bb78..b3565a5 100644
--- a/arch/arm/cpu/armv8/Kconfig
+++ b/arch/arm/cpu/armv8/Kconfig
@@ -88,7 +88,7 @@ config PSCI_RESET
 	depends on !ARCH_EXYNOS7 && !ARCH_BCM283X && !TARGET_LS2080A_EMU && \
 		   !TARGET_LS2080A_SIMU && !TARGET_LS2080AQDS && \
 		   !TARGET_LS2080ARDB && !TARGET_LS1012AQDS && \
-		   !TARGET_LS1088ARDB && \
+		   !TARGET_LS1088ARDB && !TARGET_LS1088AQDS && \
 		   !TARGET_LS1012ARDB && !TARGET_LS1012AFRDM && \
 		   !TARGET_LS1043ARDB && !TARGET_LS1043AQDS && \
 		   !TARGET_LS1046ARDB && !TARGET_LS1046AQDS && \
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
index a418c91..bf48918 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
+++ b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
@@ -229,6 +229,27 @@ config FSL_TZASC_1
 config FSL_TZASC_2
 	bool
 
+config SYS_FSL_ERRATUM_A008336
+	bool
+
+config SYS_FSL_ERRATUM_A009801
+	bool
+
+config SYS_FSL_ERRATUM_A009803
+	bool
+
+config SYS_FSL_ERRATUM_A009942
+	bool
+
+config SYS_FSL_ERRATUM_A010165
+	bool
+
+config SYS_FSL_ERRATUM_A008511
+	bool
+
+config SYS_FSL_ERRATUM_A008850
+	bool
+
 endmenu
 
 menu "Layerscape clock tree configuration"
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c b/arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c
index 9f89bd0..9f5cdd5 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c
+++ b/arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c
@@ -30,6 +30,7 @@ static struct serdes_config serdes1_cfg_tbl[] = {
 	{0x20, {QSGMII_A, QSGMII_B, SGMII1, SGMII2 }, {4, 4, 2, 2 } },
 	{0x35, {SGMII3, QSGMII_B, SGMII1, SGMII2 }, {3, 4, 3, 3 } },
 	{0x36, {QSGMII_A, QSGMII_B, SGMII1, SGMII2 }, {4, 4, 3, 3 } },
+	{0x3A, {SGMII3, PCIE1, SGMII1, SGMII2 }, {3, 5, 3, 3 } },
 		{}
 };
 static struct serdes_config serdes2_cfg_tbl[] = {
@@ -39,6 +40,7 @@ static struct serdes_config serdes2_cfg_tbl[] = {
 	{0x0E, {PCIE1, PCIE1, PCIE2, SATA1 }, {7, 7, 6, 9 }  },
 	{0x13, {PCIE1, PCIE1, PCIE3, PCIE3 }, {7, 7, 7, 7 }  },
 	{0x14, {PCIE1, PCIE2, PCIE3, PCIE3 }, {5, 5, 7, 7 }  },
+	{0x3C, {NONE, PCIE2, NONE, PCIE3 }, {0, 5, 0, 6 }  },
 	{}
 };
 
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/soc.c b/arch/arm/cpu/armv8/fsl-layerscape/soc.c
index 337d99d..f5a22ba 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/soc.c
+++ b/arch/arm/cpu/armv8/fsl-layerscape/soc.c
@@ -24,6 +24,7 @@
 #ifdef CONFIG_CHAIN_OF_TRUST
 #include <fsl_validate.h>
 #endif
+#include <fsl_immap.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 5ac8ea3..2ec5c12 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -164,6 +164,7 @@ dtb-$(CONFIG_LS102XA) += ls1021a-qds-duart.dtb \
 	ls1021a-iot-duart.dtb
 dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \
 	fsl-ls2080a-rdb.dtb \
+	fsl-ls1088a-qds.dtb \
 	fsl-ls1088a-rdb.dtb
 dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \
 	fsl-ls1043a-qds-lpuart.dtb \
diff --git a/arch/arm/dts/fsl-ls1088a-qds.dts b/arch/arm/dts/fsl-ls1088a-qds.dts
new file mode 100644
index 0000000..9b7bef4
--- /dev/null
+++ b/arch/arm/dts/fsl-ls1088a-qds.dts
@@ -0,0 +1,70 @@
+/*
+ * NXP ls1088a QDS board device tree source
+ *
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/dts-v1/;
+
+#include "fsl-ls1088a.dtsi"
+
+/ {
+	model = "NXP Layerscape 1088a QDS Board";
+	compatible = "fsl,ls1088a-qds", "fsl,ls1088a";
+	aliases {
+		spi0 = &qspi;
+		spi1 = &dspi;
+	};
+};
+
+&dspi {
+	bus-num = <0>;
+	status = "okay";
+
+	dflash0: n25q128a {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-flash";
+		reg = <0>;
+		spi-max-frequency = <1000000>; /* input clock */
+	};
+
+	dflash1: sst25wf040b {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-flash";
+		spi-max-frequency = <3500000>;
+		reg = <1>;
+	};
+
+	dflash2: en25s64 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-flash";
+		spi-max-frequency = <3500000>;
+		reg = <2>;
+	};
+};
+
+&qspi {
+	bus-num = <0>;
+	status = "okay";
+
+	qflash0: s25fs512s at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-flash";
+		spi-max-frequency = <50000000>;
+		reg = <0>;
+	};
+
+	qflash1: s25fs512s at 1 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-flash";
+		spi-max-frequency = <50000000>;
+		reg = <1>;
+	 };
+};
diff --git a/board/freescale/ls1088a/Kconfig b/board/freescale/ls1088a/Kconfig
index a4d8223..1ada661 100644
--- a/board/freescale/ls1088a/Kconfig
+++ b/board/freescale/ls1088a/Kconfig
@@ -1,3 +1,19 @@
+if TARGET_LS1088AQDS
+
+config SYS_BOARD
+	default "ls1088a"
+
+config SYS_VENDOR
+	default "freescale"
+
+config SYS_SOC
+	default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+	default "ls1088aqds"
+
+endif
+
 if TARGET_LS1088ARDB
 
 config SYS_BOARD
diff --git a/board/freescale/ls1088a/MAINTAINERS b/board/freescale/ls1088a/MAINTAINERS
index 1abbf91..e1e6d4b 100644
--- a/board/freescale/ls1088a/MAINTAINERS
+++ b/board/freescale/ls1088a/MAINTAINERS
@@ -5,5 +5,11 @@ S:	Maintained
 F:	board/freescale/ls1088a/
 F:	include/configs/ls1088ardb.h
 F:	configs/ls1088ardb_qspi_defconfig
-F:	configs/ls1088ardb_sdcard_defconfig
-F:	configs/ls1088ardb_sdcard_qspi_defconfig
+
+LS1088AQDS BOARD
+M:	Prabhakar Kushwaha <prabhakar.kushwaha at nxp.com>
+M:	Ashish Kumar <Ashish.Kumar at nxp.com>
+S:	Maintained
+F:	board/freescale/ls1088a/
+F:	include/configs/ls1088aqds.h
+F:	configs/ls1088aqds_qspi_defconfig
diff --git a/board/freescale/ls1088a/Makefile b/board/freescale/ls1088a/Makefile
index e997cf1..bdcce9e 100644
--- a/board/freescale/ls1088a/Makefile
+++ b/board/freescale/ls1088a/Makefile
@@ -6,4 +6,5 @@
 
 obj-y += ls1088a.o
 obj-$(CONFIG_TARGET_LS1088ARDB) += eth_ls1088ardb.o
+obj-$(CONFIG_TARGET_LS1088AQDS) += eth_ls1088aqds.o
 obj-y += ddr.o
diff --git a/board/freescale/ls1088a/ddr.c b/board/freescale/ls1088a/ddr.c
index 8903ff0..61b6212 100644
--- a/board/freescale/ls1088a/ddr.c
+++ b/board/freescale/ls1088a/ddr.c
@@ -25,19 +25,14 @@ void fsl_ddr_board_options(memctl_options_t *popts,
 	if (!pdimm->n_ranks)
 		return;
 
-	/*
-	 * we use identical timing for all slots. If needed, change the code
-	 * to  pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
-	 */
-	pbsp = udimms[ctrl_num];
+	pbsp = udimms[0];
 
 	/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
 	 * freqency and n_banks specified in board_specific_parameters table.
 	 */
 	ddr_freq = get_ddr_freq(0) / 1000000;
 	while (pbsp->datarate_mhz_high) {
-		if (pbsp->n_ranks == pdimm->n_ranks &&
-		    (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+		if (pbsp->n_ranks == pdimm->n_ranks) {
 			if (ddr_freq <= pbsp->datarate_mhz_high) {
 				popts->clk_adjust = pbsp->clk_adjust;
 				popts->wrlvl_start = pbsp->wrlvl_start;
@@ -63,51 +58,18 @@ void fsl_ddr_board_options(memctl_options_t *popts,
 		panic("DIMM is not supported by this board");
 	}
 found:
-#if defined(CONFIG_EMU)
 	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
 		"\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, wrlvl_ctrl_3 0x%x\n",
 		pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
 		pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
 		pbsp->wrlvl_ctl_3);
-#else
-	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
-	      pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
-
-	pdimm[0].dq_mapping[0] = 0x15;
-	pdimm[0].dq_mapping[1] = 0x35;
-	pdimm[0].dq_mapping[2] = 0x0b;
-	pdimm[0].dq_mapping[3] = 0x2c;
-	pdimm[0].dq_mapping[4] = 0x15;
-	pdimm[0].dq_mapping[5] = 0x35;
-	pdimm[0].dq_mapping[6] = 0x15;
-	pdimm[0].dq_mapping[7] = 0x35;
-	pdimm[0].dq_mapping[8] = 0xc;
-	pdimm[0].dq_mapping[9] = 0;
-	pdimm[0].dq_mapping[10] = 0;
-	pdimm[0].dq_mapping[11] = 0;
-	pdimm[0].dq_mapping[12] = 0;
-	pdimm[0].dq_mapping[13] = 0;
-	pdimm[0].dq_mapping[14] = 0;
-	pdimm[0].dq_mapping[15] = 0;
-	pdimm[0].dq_mapping[16] = 0;
-	pdimm[0].dq_mapping[17] = 0;
-
-	/* force DDR bus width to 32 bits */
-	popts->data_bus_width = 1;
+
+	popts->data_bus_width = 0;      /* 64b data bus */
 	popts->otf_burst_chop_en = 0;
 	popts->burst_length = DDR_BL8;
-	popts->bstopre = 0;	     /* enable auto precharge */
-#endif
+	popts->bstopre = 0;		/* enable auto precharge */
 
-	/*
-	 * Factors to consider for half-strength driver enable:
-	 *	- number of DIMMs installed
-	 */
-#if defined(CONFIG_EMU)
-	popts->half_strength_driver_enable = 1;
-#else
 	popts->half_strength_driver_enable = 0;
-#endif
 	/*
 	 * Write leveling override
 	 */
@@ -122,10 +84,10 @@ found:
 	/* Enable ZQ calibration */
 	popts->zq_en = 1;
 
-#if defined(CONFIG_EMU)
+#if defined(CONFIG_TARGET_LS1088AQDS)
 	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
 	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
-			  DDR_CDR2_VREF_OVRD(70);	/* Vref = 70% */
+			  DDR_CDR2_VREF_TRAIN_EN | DDR_CDR2_VREF_RANGE_2;
 #else
 	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_60ohm);
 	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_100ohm) |
@@ -134,73 +96,6 @@ found:
 	popts->cpo_sample = 0x6d;
 }
 
-#ifdef CONFIG_SYS_DDR_RAW_TIMING
-dimm_params_t ddr_raw_timing = {
-	.n_ranks = 1,
-	.rank_density = 4294967296u,
-	.capacity = 4294967296u,
-	.primary_sdram_width = 64,
-	.ec_sdram_width = 8,
-	.registered_dimm = 0,
-	.mirrored_dimm = 1,
-	.n_row_addr = 15,
-	.n_col_addr = 10,
-	.bank_addr_bits = 0,
-	.bank_group_bits = 2,
-	.edc_config = 2,
-	.burst_lengths_bitmask = 0x0c,
-
-	.tckmin_x_ps = 938,
-	.tckmax_ps = 1500,
-	.caslat_x = 0x000DFA00,
-	.taa_ps = 13500,
-	.trcd_ps = 13500,
-	.trp_ps = 13500,
-	.tras_ps = 33000,
-	.trc_ps = 46500,
-	.trfc1_ps = 260000,
-	.trfc2_ps = 160000,
-	.trfc4_ps = 110000,
-	.tfaw_ps = 21000,
-	.trrds_ps = 3700,
-	.trrdl_ps = 5300,
-	.tccdl_ps = 5355,
-	.refresh_rate_ps = 7800000,
-	.dq_mapping[0] = 0x00,
-	.dq_mapping[1] = 0x00,
-	.dq_mapping[2] = 0x00,
-	.dq_mapping[3] = 0x00,
-	.dq_mapping[4] = 0x00,
-	.dq_mapping[5] = 0x00,
-	.dq_mapping[6] = 0x00,
-	.dq_mapping[7] = 0x00,
-	.dq_mapping[8] = 0x00,
-	.dq_mapping[9] = 0x00,
-	.dq_mapping[10] = 0x00,
-	.dq_mapping[11] = 0x00,
-	.dq_mapping[12] = 0x00,
-	.dq_mapping[13] = 0x00,
-	.dq_mapping[14] = 0x00,
-	.dq_mapping[15] = 0x00,
-	.dq_mapping[16] = 0x00,
-	.dq_mapping[17] = 0x00,
-	.dq_mapping_ors = 1,
-};
-
-int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
-			    unsigned int controller_number,
-			    unsigned int dimm_number)
-{
-	static const char dimm_model[] = "Fixed DDR on board";
-
-	if (dimm_number == 0)
-		memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
-		memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
-		memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
-
-	return 0;
-}
-#endif
 
 phys_size_t initdram(int board_type)
 {
diff --git a/board/freescale/ls1088a/ddr.h b/board/freescale/ls1088a/ddr.h
index 1658c22..bfc5dae 100644
--- a/board/freescale/ls1088a/ddr.h
+++ b/board/freescale/ls1088a/ddr.h
@@ -33,9 +33,14 @@ static const struct board_specific_parameters udimm0[] = {
 	{2,  1900, 0, 4,     7, 0x09090B0D, 0x0E10120B,},
 	{2,  2300, 0, 4,     9, 0x0A0C0D11, 0x1214150E,},
 	{}
+#elif defined(CONFIG_TARGET_LS1088AQDS)
+	{2,  1666, 0, 8,     8, 0x0A0A0C0E, 0x0F10110C,},
+	{2,  1900, 0, 4,     7, 0x09090B0D, 0x0E10120B,},
+	{2,  2300, 0, 4,     9, 0x0A0C0D11, 0x1214150E,},
+	{}
 #else
-	{2,  2140, 0, 4,     4, 0x0, 0x0},
-	{1,  2140, 0, 4,     4, 0x0, 0x0},
+	{2,  2140, 0, 8,     4, 0x0, 0x0},
+	{1,  2140, 0, 8,     4, 0x0, 0x0},
 	{}
 #endif
 };
diff --git a/board/freescale/ls1088a/eth_ls1088aqds.c b/board/freescale/ls1088a/eth_ls1088aqds.c
new file mode 100644
index 0000000..3e78ac7
--- /dev/null
+++ b/board/freescale/ls1088a/eth_ls1088aqds.c
@@ -0,0 +1,650 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/fsl_serdes.h>
+#include <hwconfig.h>
+#include <fsl_mdio.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <fsl-mc/ldpaa_wriop.h>
+
+#include "../common/qixis.h"
+
+#include "ls1088a_qixis.h"
+
+#define MC_BOOT_ENV_VAR "mcinitcmd"
+
+#ifdef CONFIG_FSL_MC_ENET
+
+#define SFP_TX		0
+
+ /* - In LS1088A A there are only 16 SERDES lanes, spread across 2 SERDES banks.
+ *   Bank 1 -> Lanes A, B, C, D,
+ *   Bank 2 -> Lanes A,B, C, D,
+ */
+
+ /* Mapping of 8 SERDES lanes to LS1088A QDS board slots. A value of '0' here
+  * means that the mapping must be determined dynamically, or that the lane
+  * maps to something other than a board slot.
+  */
+
+static u8 lane_to_slot_fsm1[] = {
+	0, 0, 0, 0, 0, 0, 0, 0
+};
+
+/* On the Vitesse VSC8234XHG SGMII riser card there are 4 SGMII PHYs
+ * housed.
+ */
+
+static int xqsgii_riser_phy_addr[] = {
+	XQSGMII_CARD_PHY1_PORT0_ADDR,
+	XQSGMII_CARD_PHY2_PORT0_ADDR,
+	XQSGMII_CARD_PHY3_PORT0_ADDR,
+	XQSGMII_CARD_PHY4_PORT0_ADDR,
+	XQSGMII_CARD_PHY3_PORT2_ADDR,
+	XQSGMII_CARD_PHY1_PORT2_ADDR,
+	XQSGMII_CARD_PHY4_PORT2_ADDR,
+	XQSGMII_CARD_PHY2_PORT2_ADDR,
+};
+
+static int sgmii_riser_phy_addr[] = {
+	SGMII_CARD_PORT1_PHY_ADDR,
+	SGMII_CARD_PORT2_PHY_ADDR,
+	SGMII_CARD_PORT3_PHY_ADDR,
+	SGMII_CARD_PORT4_PHY_ADDR,
+};
+
+/* Slot2 does not have EMI connections */
+#define EMI_NONE	0xFF
+#define EMI1_RGMII1	0
+#define EMI1_RGMII2	1
+#define EMI1_SLOT1	2
+
+static const char * const mdio_names[] = {
+	"LS1088A_QDS_MDIO0",
+	"LS1088A_QDS_MDIO1",
+	"LS1088A_QDS_MDIO2",
+	DEFAULT_WRIOP_MDIO2_NAME,
+};
+
+struct ls1088a_qds_mdio {
+	u8 muxval;
+	struct mii_dev *realbus;
+};
+
+static void sgmii_configure_repeater(int dpmac)
+{
+	struct mii_dev *bus;
+	uint8_t a = 0xf;
+	int i, j, ret;
+	unsigned short value;
+	const char *dev = "LS1088A_QDS_MDIO2";
+	int i2c_addr[] = {0x58, 0x59, 0x5a, 0x5b};
+	int i2c_phy_addr = 0;
+	int phy_addr = 0;
+
+	uint8_t ch_a_eq[] = {0x1, 0x2, 0x3, 0x7};
+	uint8_t ch_a_ctl2[] = {0x81, 0x82, 0x83, 0x84};
+	uint8_t ch_b_eq[] = {0x1, 0x2, 0x3, 0x7};
+	uint8_t ch_b_ctl2[] = {0x81, 0x82, 0x83, 0x84};
+
+	/* Set I2c to Slot 1 */
+	i2c_write(0x77, 0, 0, &a, 1);
+
+	switch (dpmac) {
+	case 1:
+		i2c_phy_addr = i2c_addr[1];
+		phy_addr = 4;
+		break;
+	case 2:
+		i2c_phy_addr = i2c_addr[0];
+		phy_addr = 0;
+		break;
+	case 3:
+		i2c_phy_addr = i2c_addr[3];
+		phy_addr = 0xc;
+		break;
+	case 7:
+		i2c_phy_addr = i2c_addr[2];
+		phy_addr = 8;
+		break;
+	}
+
+	/* Check the PHY status */
+	ret = miiphy_set_current_dev(dev);
+	if (ret > 0)
+		goto error;
+
+	bus = mdio_get_current_dev();
+	debug("Reading from bus %s\n", bus->name);
+
+	ret = miiphy_write(dev, phy_addr, 0x1f, 3);
+	if (ret > 0)
+		goto error;
+
+	mdelay(10);
+	ret = miiphy_read(dev, phy_addr, 0x11, &value);
+	if (ret > 0)
+			goto error;
+
+	mdelay(10);
+
+	if ((value & 0xfff) == 0x401) {
+		miiphy_write(dev, phy_addr, 0x1f, 0);
+		printf("DPMAC %d:PHY is ..... Configured\n", dpmac);
+		return;
+	}
+
+	for (i = 0; i < 4; i++) {
+		for (j = 0; j < 4; j++) {
+			a = 0x18;
+			i2c_write(i2c_phy_addr, 6, 1, &a, 1);
+			a = 0x38;
+			i2c_write(i2c_phy_addr, 4, 1, &a, 1);
+			a = 0x4;
+			i2c_write(i2c_phy_addr, 8, 1, &a, 1);
+
+			i2c_write(i2c_phy_addr, 0xf, 1,
+				  &ch_a_eq[i], 1);
+			i2c_write(i2c_phy_addr, 0x11, 1,
+				  &ch_a_ctl2[j], 1);
+
+			i2c_write(i2c_phy_addr, 0x16, 1,
+				  &ch_b_eq[i], 1);
+			i2c_write(i2c_phy_addr, 0x18, 1,
+				  &ch_b_ctl2[j], 1);
+
+			a = 0x14;
+			i2c_write(i2c_phy_addr, 0x23, 1, &a, 1);
+			a = 0xb5;
+			i2c_write(i2c_phy_addr, 0x2d, 1, &a, 1);
+			a = 0x20;
+			i2c_write(i2c_phy_addr, 4, 1, &a, 1);
+			mdelay(100);
+			ret = miiphy_read(dev, phy_addr, 0x11, &value);
+			if (ret > 0)
+				goto error;
+
+			mdelay(100);
+			ret = miiphy_read(dev, phy_addr, 0x11, &value);
+			if (ret > 0)
+				goto error;
+
+			if ((value & 0xfff) == 0x401) {
+				printf("DPMAC %d :PHY is configured ",
+				       dpmac);
+				printf("after setting repeater 0x%x\n",
+				       value);
+				i = 5;
+				j = 5;
+			} else {
+				printf("DPMAC %d :PHY is failed to ",
+					       dpmac);
+				printf("configure the repeater 0x%x\n", value);
+			}
+		}
+	}
+	miiphy_write(dev, phy_addr, 0x1f, 0);
+error:
+	if (ret)
+		printf("DPMAC %d ..... FAILED to configure PHY\n", dpmac);
+	return;
+}
+
+static void qsgmii_configure_repeater(int dpmac)
+{
+	uint8_t a = 0xf;
+	int i, j;
+	int i2c_phy_addr = 0;
+	int phy_addr = 0;
+	int i2c_addr[] = {0x58, 0x59, 0x5a, 0x5b};
+
+	uint8_t ch_a_eq[] = {0x1, 0x2, 0x3, 0x7};
+	uint8_t ch_a_ctl2[] = {0x81, 0x82, 0x83, 0x84};
+	uint8_t ch_b_eq[] = {0x1, 0x2, 0x3, 0x7};
+	uint8_t ch_b_ctl2[] = {0x81, 0x82, 0x83, 0x84};
+
+	const char *dev = mdio_names[EMI1_SLOT1];
+	int ret = 0;
+	unsigned short value;
+
+	/* Set I2c to Slot 1 */
+	i2c_write(0x77, 0, 0, &a, 1);
+
+	switch (dpmac) {
+	case 7:
+	case 8:
+	case 9:
+	case 10:
+		i2c_phy_addr = i2c_addr[2];
+		phy_addr = 8;
+		break;
+
+	case 3:
+	case 4:
+	case 5:
+	case 6:
+		i2c_phy_addr = i2c_addr[3];
+		phy_addr = 0xc;
+		break;
+	}
+
+	/* Check the PHY status */
+	ret = miiphy_set_current_dev(dev);
+	ret = miiphy_write(dev, phy_addr, 0x1f, 3);
+	mdelay(10);
+	ret = miiphy_read(dev, phy_addr, 0x11, &value);
+	mdelay(10);
+	ret = miiphy_read(dev, phy_addr, 0x11, &value);
+	mdelay(10);
+	if ((value & 0xf) == 0xf) {
+		miiphy_write(dev, phy_addr, 0x1f, 0);
+		printf("DPMAC %d :PHY is ..... Configured\n", dpmac);
+		return;
+	}
+
+	for (i = 0; i < 4; i++) {
+		for (j = 0; j < 4; j++) {
+			a = 0x18;
+			i2c_write(i2c_phy_addr, 6, 1, &a, 1);
+			a = 0x38;
+			i2c_write(i2c_phy_addr, 4, 1, &a, 1);
+			a = 0x4;
+			i2c_write(i2c_phy_addr, 8, 1, &a, 1);
+
+			i2c_write(i2c_phy_addr, 0xf, 1, &ch_a_eq[i], 1);
+			i2c_write(i2c_phy_addr, 0x11, 1, &ch_a_ctl2[j], 1);
+
+			i2c_write(i2c_phy_addr, 0x16, 1, &ch_b_eq[i], 1);
+			i2c_write(i2c_phy_addr, 0x18, 1, &ch_b_ctl2[j], 1);
+
+			a = 0x14;
+			i2c_write(i2c_phy_addr, 0x23, 1, &a, 1);
+			a = 0xb5;
+			i2c_write(i2c_phy_addr, 0x2d, 1, &a, 1);
+			a = 0x20;
+			i2c_write(i2c_phy_addr, 4, 1, &a, 1);
+			mdelay(100);
+			ret = miiphy_read(dev, phy_addr, 0x11, &value);
+			if (ret > 0)
+				goto error;
+			mdelay(1);
+			ret = miiphy_read(dev, phy_addr, 0x11, &value);
+			if (ret > 0)
+				goto error;
+			mdelay(10);
+			if ((value & 0xf) == 0xf) {
+				miiphy_write(dev, phy_addr, 0x1f, 0);
+				printf("DPMAC %d :PHY is ..... Configured\n",
+				       dpmac);
+				return;
+			}
+		}
+	}
+error:
+	printf("DPMAC %d :PHY ..... FAILED to configure PHY\n", dpmac);
+	return;
+}
+
+static const char *ls1088a_qds_mdio_name_for_muxval(u8 muxval)
+{
+	return mdio_names[muxval];
+}
+
+struct mii_dev *mii_dev_for_muxval(u8 muxval)
+{
+	struct mii_dev *bus;
+	const char *name = ls1088a_qds_mdio_name_for_muxval(muxval);
+
+	if (!name) {
+		printf("No bus for muxval %x\n", muxval);
+		return NULL;
+	}
+
+	bus = miiphy_get_dev_by_name(name);
+
+	if (!bus) {
+		printf("No bus by name %s\n", name);
+		return NULL;
+	}
+
+	return bus;
+}
+
+static void ls1088a_qds_enable_SFP_TX(u8 muxval)
+{
+	u8 brdcfg9;
+
+	brdcfg9 = QIXIS_READ(brdcfg[9]);
+	brdcfg9 &= ~BRDCFG9_SFPTX_MASK;
+	brdcfg9 |= (muxval << BRDCFG9_SFPTX_SHIFT);
+	QIXIS_WRITE(brdcfg[9], brdcfg9);
+}
+
+static void ls1088a_qds_mux_mdio(u8 muxval)
+{
+	u8 brdcfg4;
+
+	if (muxval <= 5) {
+		brdcfg4 = QIXIS_READ(brdcfg[4]);
+		brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
+		brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT);
+		QIXIS_WRITE(brdcfg[4], brdcfg4);
+	}
+}
+
+static int ls1088a_qds_mdio_read(struct mii_dev *bus, int addr,
+				 int devad, int regnum)
+{
+	struct ls1088a_qds_mdio *priv = bus->priv;
+
+	ls1088a_qds_mux_mdio(priv->muxval);
+
+	return priv->realbus->read(priv->realbus, addr, devad, regnum);
+}
+
+static int ls1088a_qds_mdio_write(struct mii_dev *bus, int addr, int devad,
+				  int regnum, u16 value)
+{
+	struct ls1088a_qds_mdio *priv = bus->priv;
+
+	ls1088a_qds_mux_mdio(priv->muxval);
+
+	return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
+}
+
+static int ls1088a_qds_mdio_reset(struct mii_dev *bus)
+{
+	struct ls1088a_qds_mdio *priv = bus->priv;
+
+	return priv->realbus->reset(priv->realbus);
+}
+
+static int ls1088a_qds_mdio_init(char *realbusname, u8 muxval)
+{
+	struct ls1088a_qds_mdio *pmdio;
+	struct mii_dev *bus = mdio_alloc();
+
+	if (!bus) {
+		printf("Failed to allocate ls1088a_qds MDIO bus\n");
+		return -1;
+	}
+
+	pmdio = malloc(sizeof(*pmdio));
+	if (!pmdio) {
+		printf("Failed to allocate ls1088a_qds private data\n");
+		free(bus);
+		return -1;
+	}
+
+	bus->read = ls1088a_qds_mdio_read;
+	bus->write = ls1088a_qds_mdio_write;
+	bus->reset = ls1088a_qds_mdio_reset;
+	sprintf(bus->name, ls1088a_qds_mdio_name_for_muxval(muxval));
+
+	pmdio->realbus = miiphy_get_dev_by_name(realbusname);
+
+	if (!pmdio->realbus) {
+		printf("No bus with name %s\n", realbusname);
+		free(bus);
+		free(pmdio);
+		return -1;
+	}
+
+	pmdio->muxval = muxval;
+	bus->priv = pmdio;
+
+	return mdio_register(bus);
+}
+
+/*
+ * Initialize the dpmac_info array.
+ *
+ */
+static void initialize_dpmac_to_slot(void)
+{
+	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+	u32 serdes1_prtcl, cfg;
+
+	cfg = in_le32(&gur->rcwsr[FSL_CHASSIS3_SRDS1_REGSR - 1]) &
+				FSL_CHASSIS3_SRDS1_PRTCL_MASK;
+	cfg >>= FSL_CHASSIS3_SRDS1_PRTCL_SHIFT;
+	serdes1_prtcl = serdes_get_number(FSL_SRDS_1, cfg);
+
+	switch (serdes1_prtcl) {
+	case 0x12:
+		printf("qds: WRIOP: Supported SerDes1 Protocol 0x%02x\n",
+		       serdes1_prtcl);
+		lane_to_slot_fsm1[0] = EMI1_SLOT1 - 1;
+		lane_to_slot_fsm1[1] = EMI1_SLOT1 - 1;
+		lane_to_slot_fsm1[2] = EMI1_SLOT1 - 1;
+		lane_to_slot_fsm1[3] = EMI1_SLOT1 - 1;
+		break;
+	case 0x15:
+	case 0x1D:
+		printf("qds: WRIOP: Supported SerDes1 Protocol 0x%02x\n",
+		       serdes1_prtcl);
+		lane_to_slot_fsm1[0] = EMI1_SLOT1 - 1;
+		lane_to_slot_fsm1[1] = EMI1_SLOT1 - 1;
+		lane_to_slot_fsm1[2] = EMI_NONE;
+		lane_to_slot_fsm1[3] = EMI_NONE;
+		break;
+	case 0x1E:
+		printf("qds: WRIOP: Supported SerDes1 Protocol 0x%02x\n",
+		       serdes1_prtcl);
+		lane_to_slot_fsm1[0] = EMI1_SLOT1 - 1;
+		lane_to_slot_fsm1[1] = EMI1_SLOT1 - 1;
+		lane_to_slot_fsm1[2] = EMI1_SLOT1 - 1;
+		lane_to_slot_fsm1[3] = EMI_NONE;
+		break;
+	case 0x3A:
+		printf("qds: WRIOP: Supported SerDes1 Protocol 0x%02x\n",
+		       serdes1_prtcl);
+		lane_to_slot_fsm1[0] = EMI1_SLOT1 - 1;
+		lane_to_slot_fsm1[1] = EMI_NONE;
+		lane_to_slot_fsm1[2] = EMI1_SLOT1 - 1;
+		lane_to_slot_fsm1[3] = EMI1_SLOT1 - 1;
+		break;
+
+	default:
+		printf("%s qds: WRIOP: Unsupported SerDes1 Protocol 0x%02x\n",
+		       __func__, serdes1_prtcl);
+		break;
+	}
+}
+
+void ls1088a_handle_phy_interface_sgmii(int dpmac_id)
+{
+	struct mii_dev *bus;
+	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+	u32 serdes1_prtcl, cfg;
+
+	cfg = in_le32(&gur->rcwsr[FSL_CHASSIS3_SRDS1_REGSR - 1]) &
+				FSL_CHASSIS3_SRDS1_PRTCL_MASK;
+	cfg >>= FSL_CHASSIS3_SRDS1_PRTCL_SHIFT;
+	serdes1_prtcl = serdes_get_number(FSL_SRDS_1, cfg);
+
+	int *riser_phy_addr;
+	char *env_hwconfig = getenv("hwconfig");
+
+	if (hwconfig_f("xqsgmii", env_hwconfig))
+		riser_phy_addr = &xqsgii_riser_phy_addr[0];
+	else
+		riser_phy_addr = &sgmii_riser_phy_addr[0];
+
+	switch (serdes1_prtcl) {
+	case 0x12:
+	case 0x15:
+	case 0x1E:
+	case 0x3A:
+		switch (dpmac_id) {
+		case 1:
+			wriop_set_phy_address(dpmac_id, riser_phy_addr[1]);
+			break;
+		case 2:
+			wriop_set_phy_address(dpmac_id, riser_phy_addr[0]);
+			break;
+		case 3:
+			wriop_set_phy_address(dpmac_id, riser_phy_addr[3]);
+			break;
+		case 7:
+			wriop_set_phy_address(dpmac_id, riser_phy_addr[2]);
+			break;
+		default:
+			printf("WRIOP: Wrong DPMAC%d set to SGMII", dpmac_id);
+			break;
+		}
+		break;
+	default:
+		printf("%s qds: WRIOP: Unsupported SerDes1 Protocol 0x%02x\n",
+		       __func__, serdes1_prtcl);
+		return;
+	}
+	dpmac_info[dpmac_id].board_mux = EMI1_SLOT1;
+	bus = mii_dev_for_muxval(EMI1_SLOT1);
+	wriop_set_mdio(dpmac_id, bus);
+}
+
+void ls1088a_handle_phy_interface_qsgmii(int dpmac_id)
+{
+	struct mii_dev *bus;
+	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+	u32 serdes1_prtcl, cfg;
+
+	cfg = in_le32(&gur->rcwsr[FSL_CHASSIS3_SRDS1_REGSR - 1]) &
+				FSL_CHASSIS3_SRDS1_PRTCL_MASK;
+	cfg >>= FSL_CHASSIS3_SRDS1_PRTCL_SHIFT;
+	serdes1_prtcl = serdes_get_number(FSL_SRDS_1, cfg);
+
+	switch (serdes1_prtcl) {
+	case 0x1D:
+	case 0x1E:
+		switch (dpmac_id) {
+		case 3:
+		case 4:
+		case 5:
+		case 6:
+			wriop_set_phy_address(dpmac_id, dpmac_id + 9);
+			break;
+		case 7:
+		case 8:
+		case 9:
+		case 10:
+			wriop_set_phy_address(dpmac_id, dpmac_id + 1);
+			break;
+		}
+
+		dpmac_info[dpmac_id].board_mux = EMI1_SLOT1;
+		bus = mii_dev_for_muxval(EMI1_SLOT1);
+		wriop_set_mdio(dpmac_id, bus);
+		break;
+	default:
+		printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
+		       serdes1_prtcl);
+		break;
+	}
+}
+
+void ls1088a_handle_phy_interface_xsgmii(int i)
+{
+	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+	u32 serdes1_prtcl, cfg;
+
+	cfg = in_le32(&gur->rcwsr[FSL_CHASSIS3_SRDS1_REGSR - 1]) &
+				FSL_CHASSIS3_SRDS1_PRTCL_MASK;
+	cfg >>= FSL_CHASSIS3_SRDS1_PRTCL_SHIFT;
+	serdes1_prtcl = serdes_get_number(FSL_SRDS_1, cfg);
+
+	switch (serdes1_prtcl) {
+	case 0x15:
+	case 0x1D:
+	case 0x1E:
+		wriop_set_phy_address(i, i + 26);
+		ls1088a_qds_enable_SFP_TX(SFP_TX);
+		break;
+	default:
+		printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
+		       serdes1_prtcl);
+		break;
+	}
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+	int error = 0, i;
+	char *mc_boot_env_var;
+#ifdef CONFIG_FSL_MC_ENET
+	struct memac_mdio_info *memac_mdio0_info;
+	char *env_hwconfig = getenv("hwconfig");
+
+	initialize_dpmac_to_slot();
+
+	memac_mdio0_info = (struct memac_mdio_info *)malloc(
+					sizeof(struct memac_mdio_info));
+	memac_mdio0_info->regs =
+		(struct memac_mdio_controller *)
+					CONFIG_SYS_FSL_WRIOP1_MDIO1;
+	memac_mdio0_info->name = DEFAULT_WRIOP_MDIO1_NAME;
+
+	/* Register the real MDIO1 bus */
+	fm_memac_mdio_init(bis, memac_mdio0_info);
+
+	/* Register the muxing front-ends to the MDIO buses */
+	ls1088a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_RGMII1);
+	ls1088a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_RGMII2);
+	ls1088a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT1);
+
+	for (i = WRIOP1_DPMAC1; i < NUM_WRIOP_PORTS; i++) {
+		switch (wriop_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_QSGMII:
+			ls1088a_handle_phy_interface_qsgmii(i);
+			break;
+		case PHY_INTERFACE_MODE_SGMII:
+			ls1088a_handle_phy_interface_sgmii(i);
+			break;
+		case PHY_INTERFACE_MODE_XGMII:
+			ls1088a_handle_phy_interface_xsgmii(i);
+			break;
+		default:
+			break;
+
+		if (i == 16)
+			i = NUM_WRIOP_PORTS;
+		}
+	}
+
+	mc_boot_env_var = getenv(MC_BOOT_ENV_VAR);
+	if (mc_boot_env_var)
+		run_command_list(mc_boot_env_var, -1, 0);
+	error = cpu_eth_init(bis);
+
+	if (hwconfig_f("xqsgmii", env_hwconfig)) {
+		for (i = WRIOP1_DPMAC1; i < NUM_WRIOP_PORTS; i++) {
+			switch (wriop_get_enet_if(i)) {
+			case PHY_INTERFACE_MODE_QSGMII:
+				qsgmii_configure_repeater(i);
+				break;
+			case PHY_INTERFACE_MODE_SGMII:
+				sgmii_configure_repeater(i);
+				break;
+			default:
+				break;
+			}
+
+			if (i == 16)
+				i = NUM_WRIOP_PORTS;
+		}
+	}
+#endif
+	error = pci_eth_init(bis);
+	return error;
+}
diff --git a/board/freescale/ls1088a/ls1088a.c b/board/freescale/ls1088a/ls1088a.c
index b3ade52..0c8c2a5 100644
--- a/board/freescale/ls1088a/ls1088a.c
+++ b/board/freescale/ls1088a/ls1088a.c
@@ -49,11 +49,18 @@ int checkboard(void)
 					    "100 separate SSCG"};
 	int clock;
 
+#ifdef CONFIG_TARGET_LS1088AQDS
+	printf("Board: LS1088A-QDS, ");
+#else
 	printf("Board: LS1088A-RDB, ");
-
+#endif
 	sw = QIXIS_READ(arch);
 	printf("Board Arch: V%d, ", sw >> 4);
+#ifdef CONFIG_TARGET_LS1088AQDS
 	printf("Board version: %c, boot from ", (sw & 0xf) + 'A' - 1);
+#else
+	printf("Board version: %c, boot from ", (sw & 0xf) + 'A');
+#endif
 
 	memset((u8 *)buf, 0x00, ARRAY_SIZE(buf));
 
@@ -64,7 +71,27 @@ int checkboard(void)
 	puts("SD card\n");
 #endif
 	switch (sw) {
+#ifdef CONFIG_TARGET_LS1088AQDS
 	case 0:
+	case 1:
+	case 2:
+	case 3:
+	case 4:
+	case 5:
+	case 6:
+	case 7:
+		printf("vBank: %d\n", sw);
+		break;
+	case 8:
+		puts("PromJet\n");
+		break;
+	case 15:
+		puts("IFCCard\n");
+		break;
+	case 14:
+#else
+	case 0:
+#endif
 		puts("QSPI:");
 		sw = QIXIS_READ(brdcfg[0]);
 		sw = (sw & QIXIS_QMAP_MASK) >> QIXIS_QMAP_SHIFT;
@@ -81,11 +108,15 @@ int checkboard(void)
 		break;
 	}
 
+#ifdef CONFIG_TARGET_LS1088AQDS
 	printf("FPGA: v%d (%s), build %d",
 	       (int)QIXIS_READ(scver), qixis_read_tag(buf),
 	       (int)qixis_read_minor());
 	/* the timestamp string contains "\n" at the end */
 	printf(" on %s", qixis_read_time(buf));
+#else
+	printf("CPLD: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata));
+#endif
 
 	/*
 	 * Display the actual SERDES reference clocks as configured by the
@@ -113,9 +144,13 @@ int checkboard(void)
 
 bool if_board_diff_clk(void)
 {
+#ifdef CONFIG_TARGET_LS1088AQDS
+	u8 diff_conf = QIXIS_READ(brdcfg[11]);
+	return diff_conf & 0x40;
+#else
 	u8 diff_conf = QIXIS_READ(dutcfg[11]);
-
 	return diff_conf & 0x80;
+#endif
 }
 
 unsigned long get_board_sys_clk(void)
@@ -177,7 +212,7 @@ void board_retimer_init(void)
 {
 	u8 reg;
 
-	/* Retimer is connected to I2C1_CH7_CH5 */
+	/* Retimer is connected to I2C1_CH5 */
 	select_i2c_ch_pca9547(I2C_MUX_CH5);
 
 	/* Access to Control/Shared register */
@@ -197,26 +232,10 @@ void board_retimer_init(void)
 	reg |= 0x4;
 	i2c_write(I2C_RETIMER_ADDR, 0, 1, &reg, 1);
 
-	/* Enable override divider select and Enable Override Output Mux */
-	i2c_read(I2C_RETIMER_ADDR, 9, 1, &reg, 1);
-	reg |= 0x24;
-	i2c_write(I2C_RETIMER_ADDR, 9, 1, &reg, 1);
-
-	/* Select VCO Divider to full rate (000) */
-	i2c_read(I2C_RETIMER_ADDR, 0x18, 1, &reg, 1);
-	reg &= 0x8f;
-	i2c_write(I2C_RETIMER_ADDR, 0x18, 1, &reg, 1);
-
-	/* Selects active PFD MUX Input as Re-timed Data (001) */
-	i2c_read(I2C_RETIMER_ADDR, 0x1e, 1, &reg, 1);
-	reg &= 0x3f;
-	reg |= 0x20;
-	i2c_write(I2C_RETIMER_ADDR, 0x1e, 1, &reg, 1);
-
 	/* Set data rate as 10.3125 Gbps */
-	reg = 0x0;
+	reg = 0x90;
 	i2c_write(I2C_RETIMER_ADDR, 0x60, 1, &reg, 1);
-	reg = 0xb0;
+	reg = 0xb3;
 	i2c_write(I2C_RETIMER_ADDR, 0x61, 1, &reg, 1);
 	reg = 0x90;
 	i2c_write(I2C_RETIMER_ADDR, 0x62, 1, &reg, 1);
@@ -225,6 +244,51 @@ void board_retimer_init(void)
 	reg = 0xcd;
 	i2c_write(I2C_RETIMER_ADDR, 0x64, 1, &reg, 1);
 
+	/* Select VCO Divider to full rate (000) */
+	i2c_read(I2C_RETIMER_ADDR, 0x2F, 1, &reg, 1);
+	reg &= 0x0f;
+	reg |= 0x70;
+	i2c_write(I2C_RETIMER_ADDR, 0x2F, 1, &reg, 1);
+
+#ifdef	CONFIG_TARGET_LS1088AQDS
+	/* Retimer is connected to I2C1_CH5 */
+	select_i2c_ch_pca9547(I2C_MUX_CH5);
+
+	/* Access to Control/Shared register */
+	reg = 0x0;
+	i2c_write(I2C_RETIMER_ADDR2, 0xff, 1, &reg, 1);
+
+	/* Read device revision and ID */
+	i2c_read(I2C_RETIMER_ADDR2, 1, 1, &reg, 1);
+	debug("Retimer version id = 0x%x\n", reg);
+
+	/* Enable Broadcast. All writes target all channel register sets */
+	reg = 0x0c;
+	i2c_write(I2C_RETIMER_ADDR2, 0xff, 1, &reg, 1);
+
+	/* Reset Channel Registers */
+	i2c_read(I2C_RETIMER_ADDR2, 0, 1, &reg, 1);
+	reg |= 0x4;
+	i2c_write(I2C_RETIMER_ADDR2, 0, 1, &reg, 1);
+
+	/* Set data rate as 10.3125 Gbps */
+	reg = 0x90;
+	i2c_write(I2C_RETIMER_ADDR2, 0x60, 1, &reg, 1);
+	reg = 0xb3;
+	i2c_write(I2C_RETIMER_ADDR2, 0x61, 1, &reg, 1);
+	reg = 0x90;
+	i2c_write(I2C_RETIMER_ADDR2, 0x62, 1, &reg, 1);
+	reg = 0xb3;
+	i2c_write(I2C_RETIMER_ADDR2, 0x63, 1, &reg, 1);
+	reg = 0xcd;
+	i2c_write(I2C_RETIMER_ADDR2, 0x64, 1, &reg, 1);
+
+	/* Select VCO Divider to full rate (000) */
+	i2c_read(I2C_RETIMER_ADDR2, 0x2F, 1, &reg, 1);
+	reg &= 0x0f;
+	reg |= 0x70;
+	i2c_write(I2C_RETIMER_ADDR2, 0x2F, 1, &reg, 1);
+#endif
 	/*return the default channel*/
 	select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
 }
diff --git a/board/freescale/ls1088a/ls1088a_qixis.h b/board/freescale/ls1088a/ls1088a_qixis.h
index 9757d1b..4790461 100644
--- a/board/freescale/ls1088a/ls1088a_qixis.h
+++ b/board/freescale/ls1088a/ls1088a_qixis.h
@@ -31,4 +31,9 @@
 #define QIXIS_SDCLK1_165		0x2
 #define QIXIS_SDCLK1_100_SP		0x3
 
+#define BRDCFG4_EMISEL_MASK		0xE0
+#define BRDCFG4_EMISEL_SHIFT		5
+#define BRDCFG9_SFPTX_MASK		0x10
+#define BRDCFG9_SFPTX_SHIFT		4
+
 #endif
diff --git a/configs/ls1088aqds_qspi_defconfig b/configs/ls1088aqds_qspi_defconfig
new file mode 100644
index 0000000..3511d92
--- /dev/null
+++ b/configs/ls1088aqds_qspi_defconfig
@@ -0,0 +1,27 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1088AQDS=y
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1088a-qds"
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4, QSPI_BOOT"
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_OF_CONTROL=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_E1000=y
+CONFIG_SYS_NS16550=y
+CONFIG_FSL_DSPI=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
diff --git a/configs/ls1088ardb_qspi_defconfig b/configs/ls1088ardb_qspi_defconfig
index 223d581..a0559a7 100644
--- a/configs/ls1088ardb_qspi_defconfig
+++ b/configs/ls1088ardb_qspi_defconfig
@@ -9,19 +9,13 @@ CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_STDOUT_VIA_ALIAS=y
 CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4, QSPI_BOOT"
-CONFIG_BOOTDELAY=10
 CONFIG_HUSH_PARSER=y
-CONFIG_CMD_GREPENV=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_SF=y
 CONFIG_CMD_I2C=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
 CONFIG_OF_CONTROL=y
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_DM=y
diff --git a/include/configs/ls1088a_common.h b/include/configs/ls1088a_common.h
index 5f976b8..f882d6a 100644
--- a/include/configs/ls1088a_common.h
+++ b/include/configs/ls1088a_common.h
@@ -33,9 +33,6 @@
 #define  CONFIG_SPI_FLASH_BAR
 #define CONFIG_SKIP_LOWLEVEL_INIT
 
-/* Flat Device Tree Definitions */
-/* #define CONFIG_OF_LIBFDT */
-
 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
 
 #define CONFIG_VERY_BIG_RAM
@@ -140,6 +137,11 @@ unsigned long long get_qixis_addr(void);
 
 /* Command line configuration */
 #define CONFIG_CMD_ENV
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
 
 /* Miscellaneous configurable options */
 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
diff --git a/include/configs/ls1088aqds.h b/include/configs/ls1088aqds.h
new file mode 100644
index 0000000..b1189ea
--- /dev/null
+++ b/include/configs/ls1088aqds.h
@@ -0,0 +1,403 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __LS1088A_QDS_H
+#define __LS1088A_QDS_H
+
+#include "ls1088a_common.h"
+
+#ifdef CONFIG_QSPI_BOOT
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+#else
+#define CONFIG_DISPLAY_BOARDINFO
+#endif
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+#if defined(CONFIG_SD_BOOT)
+#define CONFIG_ENV_OFFSET		(2 * 1024 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_ENV_SIZE			0x2000
+#elif defined(CONFIG_QSPI_BOOT)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE			0x2000          /* 8KB */
+#define CONFIG_ENV_OFFSET		0x200000        /* 2MB */
+#define CONFIG_ENV_SECT_SIZE		0x40000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x200000)
+#define CONFIG_ENV_SECT_SIZE		0x20000
+#define CONFIG_ENV_SIZE			0x20000
+#endif
+
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_QIXIS_I2C_ACCESS
+#define SYS_NO_FLASH
+#define CONFIG_SYS_I2C_EARLY_INIT /* swap get_board_sys_clk else part here*/
+#undef CONFIG_CMD_IMLS
+#define CONFIG_SYS_CLK_FREQ		100000000
+#define CONFIG_DDR_CLK_FREQ		100000000
+#else
+#define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
+#define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
+#endif
+
+#define COUNTER_FREQUENCY_REAL		(CONFIG_SYS_CLK_FREQ/4)
+#define COUNTER_FREQUENCY		25000000	/* 25MHz */
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+
+#define CONFIG_DDR_SPD
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE           0xdeadbeef
+#define SPD_EEPROM_ADDRESS		0x51
+#define CONFIG_SYS_SPD_BUS_NUM		0
+
+
+/*
+ * IFC Definitions
+ */
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
+#define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128*1024*1024)
+#define CONFIG_SYS_NOR_AMASK_EARLY	IFC_AMASK(64*1024*1024)
+
+#define CONFIG_SYS_NOR0_CSPR					\
+	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)		| \
+	CSPR_PORT_SIZE_16					| \
+	CSPR_MSEL_NOR						| \
+	CSPR_V)
+#define CONFIG_SYS_NOR0_CSPR_EARLY				\
+	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)	| \
+	CSPR_PORT_SIZE_16					| \
+	CSPR_MSEL_NOR						| \
+	CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR					\
+	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS)		| \
+	CSPR_PORT_SIZE_16					| \
+	CSPR_MSEL_NOR						| \
+	CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EARLY				\
+	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS_EARLY)	| \
+	CSPR_PORT_SIZE_16					| \
+	CSPR_MSEL_NOR						| \
+	CSPR_V)
+#define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(12)
+#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
+				FTIM0_NOR_TEADC(0x5) | \
+				FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
+				FTIM1_NOR_TRAD_NOR(0x1a) |\
+				FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
+				FTIM2_NOR_TCH(0x4) | \
+				FTIM2_NOR_TWPH(0x0E) | \
+				FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3	0x04000000
+#define CONFIG_SYS_IFC_CCR	0x01000000
+
+#ifndef SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE,\
+					 CONFIG_SYS_FLASH_BASE + 0x40000000}
+#endif
+#endif
+
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_MAX_ECCPOS	256
+#define CONFIG_SYS_NAND_MAX_OOBFREE	2
+
+#define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)
+
+#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
+				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
+				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
+				| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
+				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
+					FTIM0_NAND_TWP(0x18)   | \
+					FTIM0_NAND_TWCHT(0x07) | \
+					FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
+					FTIM1_NAND_TWBE(0x39)  | \
+					FTIM1_NAND_TRR(0x0e)   | \
+					FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
+					FTIM2_NAND_TREH(0x0a) | \
+					FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3		0x0
+
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+
+#define CONFIG_FSL_QIXIS
+#define CONFIG_SYS_I2C_FPGA_ADDR	0x66
+#define QIXIS_LBMAP_SWITCH		6
+#define QIXIS_QMAP_MASK			0xe0
+#define QIXIS_QMAP_SHIFT		5
+#define QIXIS_LBMAP_MASK		0x0f
+#define QIXIS_LBMAP_SHIFT		0
+#define QIXIS_LBMAP_DFLTBANK		0x0e
+#define QIXIS_LBMAP_ALTBANK		0x2e
+#define QIXIS_LBMAP_SD			0x00
+#define QIXIS_LBMAP_SD_QSPI		0x0e
+#define QIXIS_LBMAP_QSPI		0x0e
+#define QIXIS_RCW_SRC_SD		0x40
+#define QIXIS_RCW_SRC_QSPI		0x62
+#define QIXIS_RST_CTL_RESET		0x41
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
+#define	QIXIS_RST_FORCE_MEM		0x01
+#define QIXIS_STAT_PRES1		0xb
+#define QIXIS_SDID_MASK			0x07
+#define QIXIS_ESDHC_NO_ADAPTER		0x7
+
+#define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
+#define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
+					| CSPR_PORT_SIZE_8 \
+					| CSPR_MSEL_GPCM \
+					| CSPR_V)
+#define SYS_FPGA_CSPR_FINAL	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+					| CSPR_PORT_SIZE_8 \
+					| CSPR_MSEL_GPCM \
+					| CSPR_V)
+
+#define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64*1024)
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_SYS_FPGA_CSOR		CSOR_GPCM_ADM_SHIFT(0)
+#else
+#define CONFIG_SYS_FPGA_CSOR		CSOR_GPCM_ADM_SHIFT(12)
+#endif
+/* QIXIS Timing parameters*/
+#define SYS_FPGA_CS_FTIM0	(FTIM0_GPCM_TACSE(0x0e) | \
+					FTIM0_GPCM_TEADC(0x0e) | \
+					FTIM0_GPCM_TEAHC(0x0e))
+#define SYS_FPGA_CS_FTIM1	(FTIM1_GPCM_TACO(0xff) | \
+					FTIM1_GPCM_TRAD(0x3f))
+#define SYS_FPGA_CS_FTIM2	(FTIM2_GPCM_TCS(0xf) | \
+					FTIM2_GPCM_TCH(0xf) | \
+					FTIM2_GPCM_TWP(0x3E))
+#define SYS_FPGA_CS_FTIM3	0x0
+
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_FPGA_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_FPGA_CSPR
+#define CONFIG_SYS_CSPR2_FINAL		SYS_FPGA_CSPR_FINAL
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_FPGA_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_FPGA_CSOR
+#define CONFIG_SYS_CS2_FTIM0		SYS_FPGA_CS_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		SYS_FPGA_CS_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		SYS_FPGA_CS_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		SYS_FPGA_CS_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR_EARLY
+#define CONFIG_SYS_CSPR0_FINAL		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR_EARLY
+#define CONFIG_SYS_CSPR1_FINAL		CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK_EARLY
+#define CONFIG_SYS_AMASK1_FINAL		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
+#define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
+#define CONFIG_SYS_CSPR3_FINAL		CONFIG_SYS_FPGA_CSPR_FINAL
+#define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
+#define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
+#define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_CS_FTIM0
+#define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_CS_FTIM1
+#define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_CS_FTIM2
+#define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_CS_FTIM3
+#endif
+
+#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
+
+/*
+ * I2C bus multiplexer
+ */
+#define I2C_MUX_PCA_ADDR_PRI		0x77
+#define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
+#define I2C_RETIMER_ADDR		0x18
+#define I2C_RETIMER_ADDR2		0x19
+#define I2C_MUX_CH_DEFAULT		0x8
+#define I2C_MUX_CH5			0xD
+
+/*
+* RTC configuration
+*/
+#define RTC
+#define CONFIG_RTC_PCF8563 1
+#define CONFIG_SYS_I2C_RTC_ADDR         0x51  /* Channel 3*/
+#define CONFIG_CMD_DATE
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM		0
+#define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
+
+/* QSPI device */
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_FSL_QSPI
+#define CONFIG_SPI_FLASH_SPANSION
+#define FSL_QSPI_FLASH_SIZE		(1 << 26)
+#define FSL_QSPI_FLASH_NUM		2
+#define CONFIG_SYS_FSL_QSPI_AHB
+#endif
+
+#ifdef CONFIG_FSL_DSPI
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SPI_FLASH_EON
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SF_DEFAULT_BUS		1
+#define CONFIG_SF_DEFAULT_CS		0
+#endif
+#endif
+
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		0x9fffffff
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+
+#define CONFIG_FSL_MEMAC
+
+/*  MMC  */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#define CONFIG_ESDHC_DETECT_QUIRK ((readb(QIXIS_BASE + QIXIS_STAT_PRES1) & \
+	QIXIS_SDID_MASK) != QIXIS_ESDHC_NO_ADAPTER)
+
+/* Initial environment variables */
+#undef CONFIG_EXTRA_ENV_SETTINGS
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
+	"loadaddr=0x90100000\0"			\
+	"kernel_addr=0x100000\0"		\
+	"ramdisk_addr=0x800000\0"		\
+	"ramdisk_size=0x2000000\0"		\
+	"fdt_high=0xa0000000\0"			\
+	"initrd_high=0xffffffffffffffff\0"	\
+	"kernel_start=0x1100000\0"		\
+	"kernel_load=0xa0000000\0"		\
+	"kernel_size=0x2800000\0"		\
+	"mcinitcmd=sf probe 0:0;sf read 0x80000000 0x300000 0x100000;"	\
+	"sf read 0x80100000 0x800000 0x100000;" \
+	"fsl_mc start mc 0x80000000 0x80100000\0"	\
+	"mcmemsize=0x70000000 \0"
+
+#ifdef CONFIG_FSL_MC_ENET
+#define CONFIG_FSL_MEMAC
+#define	CONFIG_PHYLIB
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#define CONFIG_PHY_TERANETICS
+#define RGMII_PHY1_ADDR		0x1
+#define RGMII_PHY2_ADDR		0x2
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1d
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+
+#define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0
+#define XQSGMII_CARD_PHY1_PORT1_ADDR 0x1
+#define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2
+#define XQSGMII_CARD_PHY1_PORT3_ADDR 0x3
+#define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4
+#define XQSGMII_CARD_PHY2_PORT1_ADDR 0x5
+#define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6
+#define XQSGMII_CARD_PHY2_PORT3_ADDR 0x7
+#define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8
+#define XQSGMII_CARD_PHY3_PORT1_ADDR 0x9
+#define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa
+#define XQSGMII_CARD_PHY3_PORT3_ADDR 0xb
+#define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc
+#define XQSGMII_CARD_PHY4_PORT1_ADDR 0xd
+#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
+#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
+
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_ETHPRIME		"DPMAC1 at xgmii"
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+
+#endif
+
+#undef CONFIG_CMDLINE_EDITING
+#include <config_distro_defaults.h>
+#define BOOT_TARGET_DEVICES(func) \
+	func(USB, usb, 0) \
+	func(MMC, mmc, 0) \
+	func(SCSI, scsi, 0) \
+	func(DHCP, dhcp, na)
+#include <config_distro_bootcmd.h>
+
+#include <asm/fsl_secure_boot.h>
+
+#endif /* __LS1088A_QDS_H */
-- 
1.9.1



More information about the U-Boot mailing list