[U-Boot] socfpga qspi issues on SoCKit devkit

[Marek Vasut]

On 02/20/2017 05:25 AM, Vignesh R wrote:
> + Marek

Thanks, +CC Dinh and Ley

> On Friday 17 February 2017 05:02 AM, Rush, Jason A. wrote:
>> The QSPI NOR interface on the Altera Cyclone V SoCKit devkit (Rev B) appears to be broken in the current release.  I've tracked it down to working in the v2016.07 release, but broken in the the v2016.09 release.  With the help of git bisect, I tracked down the commit that breaks the QSPI to the following:
>>
>>   commit dac3bf20fb2c9b03476be0d73db620f62ab3cee1
>>   Author: Vignesh R <vigneshr at ti.com>
>>   Date:   Wed Jul 6 10:20:55 2016 +0530
>>
>>       spi: cadence_qspi_apb: Support 32 bit AHB address
>>
>>       AHB address can be as long as 32 bit, hence remove the
>>       CQSPI_REG_INDIRECTRDSTARTADDR mask. Since AHB address is passed from DT
>>       and read as u32 value, it anyway does not make sense to mask upper bits.
>>
>>       Signed-off-by: Vignesh R <vigneshr at ti.com>
>>       Tested-by: Marek Vasut <marex at denx.de>
>>       Acked-by: Marek Vasut <marex at denx.de>
>>       Reviewed-by: Jagan Teki <jteki at openedev.com>
>>
>> When I try and read anything from the QSPI on the dac3bf20fb2c9b03476be0d73db620f62ab3cee1 commit I get a "data abort" and the CPU resets.  Example output below is from a clean build of U-Boot configured with socfpga_sockit_defconfig:
>>
>>  => sf probe
>>   SF: Detected N25Q1024 with page size 256 Bytes, erase size 64 KiB, total 128 MiB
>>   => sf read 0x2000000 0x50000 0x5000
>>   device 0 offset 0x50000, size 0x5000
>>   data abort
>>   pc : [<3ff7a9bc>]          lr : [<3ff98359>]
>>   reloc pc : [<010249fc>]    lr : [<01042399>]
>>   sp : 3bf4fde8  ip : 3ff7a371     fp : 00000002
>>   r10: 00000000  r9 : 3bf54ee8     r8 : 3bf55530
>>   r7 : 0000270d  r6 : 02000000     r5 : 00005000  r4 : 3bf55530
>>   r3 : 00000004  r2 : 00000000     r1 : 02000000  r0 : ffa00000
>>   Flags: nZCv  IRQs off  FIQs off  Mode SVC_32
>>   Resetting CPU ...
>>
>> When I run the same commands with the previous commit in the git log (fdf02a36c52cb96717b64113775c4251ecd49596) I get the following output:
>>
>>   => sf probe
>>   SF: Detected N25Q1024 with page size 256 Bytes, erase size 64 KiB, total 128 MiB
>>   => sf read 0x2000000 0x50000 0x5000
>>   device 0 offset 0x50000, size 0x5000
>>   SF: 20480 bytes @ 0x50000 Read: OK
>>   =>
>>
>> I've done some investigation, and previously the ahbbase was masked so the value 0xFFA0_0000 results in 0x0 when writing the CQSPI_REG_INDIRECTTRIGGER register.  I assume the above commit works on some boards, but it appears to break the socfpga arch.
>>
>> Is there someone that could help investigate or confirm this?
> 
> I am looking at cyclone5_handbook.pdf [1] and it says indaddrtrig field
> is 32 bit wide. So, I wonder why masking is needed. If you specify
> ahbbase as  0xFFA0_0000 in DT(reg property) then the expectation is
> 0xFFA0_0000 gets written to indaddrtrig reg. It looks like the trigger
> address is 0x0 and not 0xFFA0_0000, therefore you may have to update reg
> property in DT to reflect the same.
> 
> [1]https://www.altera.com/en_US/pdfs/literature/hb/cyclone-v/cyclone5_handbook.pdf
> 
> 


-- 
Best regards,
Marek Vasut