[U-Boot] [PATCH v5 7/9] STiH410: Add STi pinctrl driver

patrice.chotard at st.com patrice.chotard at st.com
Mon Feb 20 09:31:47 UTC 2017


From: Patrice Chotard <patrice.chotard at st.com>

Add STMicroelectronics STiH410 pinctrl driver

Signed-off-by: Patrice Chotard <patrice.chotard at st.com>
Reviewed-by: Tom Rini <trini at konsulko.com>
Reviewed-by: Simon Glass <sjg at chromium.org>
---
 drivers/pinctrl/Kconfig       |  10 ++
 drivers/pinctrl/Makefile      |   1 +
 drivers/pinctrl/pinctrl-sti.c | 320 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 331 insertions(+)
 create mode 100644 drivers/pinctrl/pinctrl-sti.c

diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index efcb4c0..0c832e1 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -175,6 +175,16 @@ config PIC32_PINCTRL
 	  by a device tree node which contains both GPIO defintion and pin control
 	  functions.
 
+config PINCTRL_STI
+	bool "STMicroelectronics STi pin-control and pin-mux driver"
+	depends on DM && ARCH_STI
+	default y
+	help
+	  Support pin multiplexing control on STMicrolectronics STi SoCs.
+	  The driver is controlled by a device tree node which contains both
+	  the GPIO definitions and pin control functions for each available multiplex
+	  function.
+
 endif
 
 source "drivers/pinctrl/meson/Kconfig"
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index 512112a..a2f8101 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -16,3 +16,4 @@ obj-$(CONFIG_PIC32_PINCTRL)	+= pinctrl_pic32.o
 obj-$(CONFIG_PINCTRL_EXYNOS)	+= exynos/
 obj-$(CONFIG_PINCTRL_MESON)	+= meson/
 obj-$(CONFIG_PINCTRL_MVEBU)	+= mvebu/
+obj-$(CONFIG_PINCTRL_STI)	+= pinctrl-sti.o
diff --git a/drivers/pinctrl/pinctrl-sti.c b/drivers/pinctrl/pinctrl-sti.c
new file mode 100644
index 0000000..6ee7fa7
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-sti.c
@@ -0,0 +1,320 @@
+/*
+ * Pinctrl driver for STMicroelectronics STi SoCs
+ *
+ *  Copyright (c) 2017
+ *  Patrice Chotard <patrice.chotard at st.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0
+ */
+
+#include <common.h>
+#include <bitfield.h>
+#include <dm.h>
+#include <errno.h>
+#include <regmap.h>
+#include <syscon.h>
+#include <asm/io.h>
+#include <dm/pinctrl.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define MAX_STI_PINCONF_ENTRIES		7
+/* Output enable */
+#define OE			(1 << 27)
+/* Pull Up */
+#define PU			(1 << 26)
+/* Open Drain */
+#define OD			(1 << 25)
+
+/* User-frendly defines for Pin Direction */
+		/* oe = 0, pu = 0, od = 0 */
+#define IN			(0)
+		/* oe = 0, pu = 1, od = 0 */
+#define IN_PU			(PU)
+		/* oe = 1, pu = 0, od = 0 */
+#define OUT			(OE)
+		/* oe = 1, pu = 1, od = 0 */
+#define OUT_PU			(OE | PU)
+		/* oe = 1, pu = 0, od = 1 */
+#define BIDIR			(OE | OD)
+		/* oe = 1, pu = 1, od = 1 */
+#define BIDIR_PU		(OE | PU | OD)
+
+struct sti_pinctrl_platdata {
+	struct regmap *regmap;
+};
+
+struct sti_pin_desc {
+	unsigned char bank;
+	unsigned char pin;
+	unsigned char alt;
+	int dir;
+};
+
+/*
+ * PIO alternative Function selector
+ */
+void sti_alternate_select(struct udevice *dev, struct sti_pin_desc *pin_desc)
+{
+	struct sti_pinctrl_platdata *plat = dev_get_platdata(dev);
+	unsigned long sysconf, *sysconfreg;
+	int alt = pin_desc->alt;
+	int bank = pin_desc->bank;
+	int pin = pin_desc->pin;
+
+	sysconfreg = (unsigned long *)plat->regmap->base;
+
+	switch (bank) {
+	case 0 ... 5:		/* in "SBC Bank" */
+		sysconfreg += bank;
+		break;
+	case 10 ... 20:		/* in "FRONT Bank" */
+		sysconfreg += bank - 10;
+		break;
+	case 30 ... 35:		/* in "REAR Bank" */
+		sysconfreg += bank - 30;
+		break;
+	case 40 ... 42:		/* in "FLASH Bank" */
+		sysconfreg += bank - 40;
+		break;
+	default:
+		BUG();
+		return;
+	}
+
+	sysconf = readl(sysconfreg);
+	bitfield_replace(sysconf, pin * 4, 3, alt);
+	writel(sysconf, sysconfreg);
+}
+
+/* pin configuration */
+void sti_pin_configure(struct udevice *dev, struct sti_pin_desc *pin_desc)
+{
+	struct sti_pinctrl_platdata *plat = dev_get_platdata(dev);
+	int bit;
+	int oe = 0, pu = 0, od = 0;
+	unsigned long *sysconfreg;
+	int bank = pin_desc->bank;
+
+	sysconfreg = (unsigned long *)plat->regmap->base + 40;
+
+	/*
+	 * NOTE: The PIO configuration for the PIO pins in the
+	 * "FLASH Bank" are different from all the other banks!
+	 * Specifically, the output-enable pin control register
+	 * (SYS_CFG_3040) and the pull-up pin control register
+	 * (SYS_CFG_3050), are both classed as being "reserved".
+	 * Hence, we do not write to these registers to configure
+	 * the OE and PU features for PIOs in this bank. However,
+	 * the open-drain pin control register (SYS_CFG_3060)
+	 * follows the style of the other banks, and so we can
+	 * treat that register normally.
+	 *
+	 * Being pedantic, we should configure the PU and PD features
+	 * in the "FLASH Bank" explicitly instead using the four
+	 * SYS_CFG registers: 3080, 3081, 3085, and 3086. However, this
+	 * would necessitate passing in the alternate function number
+	 * to this function, and adding some horrible complexity here.
+	 * Alternatively, we could just perform 4 32-bit "pokes" to
+	 * these four SYS_CFG registers early in the initialization.
+	 * In practice, these four SYS_CFG registers are correct
+	 * after a reset, and U-Boot does not need to change them, so
+	 * we (cheat and) rely on these registers being correct.
+	 * WARNING: Please be aware of this (pragmatic) behaviour!
+	 */
+	int flashss = 0;	/* bool: PIO in the Flash Sub-System ? */
+
+	switch (pin_desc->dir) {
+	case IN:
+		oe = 0; pu = 0; od = 0;
+		break;
+	case IN_PU:
+		oe = 0; pu = 1; od = 0;
+		break;
+	case OUT:
+		oe = 1; pu = 0; od = 0;
+		break;
+	case BIDIR:
+		oe = 1; pu = 0; od = 1;
+		break;
+	case BIDIR_PU:
+		oe = 1; pu = 1; od = 1;
+		break;
+
+	default:
+		error("%s invalid direction value: 0x%x\n",
+		      __func__, pin_desc->dir);
+		BUG();
+		break;
+	}
+
+	switch (bank) {
+	case 0 ... 5:		/* in "SBC Bank" */
+		sysconfreg += bank / 4;
+		break;
+	case 10 ... 20:		/* in "FRONT Bank" */
+		bank -= 10;
+		sysconfreg += bank / 4;
+		break;
+	case 30 ... 35:		/* in "REAR Bank" */
+		bank -= 30;
+		sysconfreg += bank / 4;
+		break;
+	case 40 ... 42:		/* in "FLASH Bank" */
+		bank -= 40;
+		sysconfreg += bank / 4;
+		flashss = 1;	/* pin is in the Flash Sub-System */
+		break;
+	default:
+		BUG();
+		return;
+	}
+
+	bit = ((bank * 8) + pin_desc->pin) % 32;
+
+	/*
+	 * set the "Output Enable" pin control
+	 * but, do nothing if in the flashSS
+	 */
+	if (!flashss) {
+		if (oe)
+			generic_set_bit(bit, sysconfreg);
+		else
+			generic_clear_bit(bit, sysconfreg);
+	}
+
+	sysconfreg += 10;	/* skip to next set of syscfg registers */
+
+	/*
+	 * set the "Pull Up" pin control
+	 * but, do nothing if in the FlashSS
+	 */
+
+	if (!flashss) {
+		if (pu)
+			generic_set_bit(bit, sysconfreg);
+		else
+			generic_clear_bit(bit, sysconfreg);
+	}
+
+	sysconfreg += 10;	/* skip to next set of syscfg registers */
+
+	/* set the "Open Drain Enable" pin control */
+	if (od)
+		generic_set_bit(bit, sysconfreg);
+	else
+		generic_clear_bit(bit, sysconfreg);
+}
+
+
+static int sti_pinctrl_set_state(struct udevice *dev, struct udevice *config)
+{
+	struct fdtdec_phandle_args args;
+	const void *blob = gd->fdt_blob;
+	const char *prop_name;
+	int node = dev_of_offset(config);
+	int property_offset, prop_len;
+	int pinconf_node, ret, count;
+	const char *bank_name;
+	u32 cells[MAX_STI_PINCONF_ENTRIES];
+
+	struct sti_pin_desc pin_desc;
+
+	/* go to next node "st,pins" which contains the pins configuration */
+	pinconf_node = fdt_subnode_offset(blob, node, "st,pins");
+
+	/*
+	 * parse each pins configuration which looks like :
+	 *	pin_name = <bank_phandle pin_nb alt dir rt_type rt_delay rt_clk>
+	 */
+
+	fdt_for_each_property_offset(property_offset, blob, pinconf_node) {
+		fdt_getprop_by_offset(blob, property_offset, &prop_name,
+				      &prop_len);
+
+		/* extract the bank of the pin description */
+		ret = fdtdec_parse_phandle_with_args(blob, pinconf_node,
+						     prop_name, "#gpio-cells",
+						     0, 0, &args);
+		if (ret < 0) {
+			error("Can't get the gpio bank phandle: %d\n", ret);
+			return ret;
+		}
+
+		bank_name = fdt_getprop(blob, args.node, "st,bank-name",
+					&count);
+		if (count < 0) {
+			error("Can't find bank-name property %d\n", count);
+			return -EINVAL;
+		}
+
+		pin_desc.bank = trailing_strtoln(bank_name, NULL);
+
+		count = fdtdec_get_int_array_count(blob, pinconf_node,
+						   prop_name, cells,
+						   ARRAY_SIZE(cells));
+		if (count < 0) {
+			error("Bad pin configuration array %d\n", count);
+			return -EINVAL;
+		}
+
+		if (count > MAX_STI_PINCONF_ENTRIES) {
+			error("Unsupported pinconf array count %d\n", count);
+			return -EINVAL;
+		}
+
+		pin_desc.pin = cells[1];
+		pin_desc.alt = cells[2];
+		pin_desc.dir = cells[3];
+
+		sti_alternate_select(dev, &pin_desc);
+		sti_pin_configure(dev, &pin_desc);
+	};
+
+	return 0;
+}
+
+static int sti_pinctrl_probe(struct udevice *dev)
+{
+	struct sti_pinctrl_platdata *plat = dev_get_platdata(dev);
+	struct udevice *syscon;
+	int err;
+
+	/* get corresponding syscon phandle */
+	err = uclass_get_device_by_phandle(UCLASS_SYSCON, dev,
+					   "st,syscfg", &syscon);
+	if (err) {
+		error("unable to find syscon device\n");
+		return err;
+	}
+
+	plat->regmap = syscon_get_regmap(syscon);
+	if (!plat->regmap) {
+		error("unable to find regmap\n");
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static const struct udevice_id sti_pinctrl_ids[] = {
+	{ .compatible = "st,stih407-sbc-pinctrl" },
+	{ .compatible = "st,stih407-front-pinctrl" },
+	{ .compatible = "st,stih407-rear-pinctrl" },
+	{ .compatible = "st,stih407-flash-pinctrl" },
+	{ }
+};
+
+const struct pinctrl_ops sti_pinctrl_ops = {
+	.set_state = sti_pinctrl_set_state,
+};
+
+U_BOOT_DRIVER(pinctrl_sti) = {
+	.name = "pinctrl_sti",
+	.id = UCLASS_PINCTRL,
+	.of_match = sti_pinctrl_ids,
+	.ops = &sti_pinctrl_ops,
+	.probe = sti_pinctrl_probe,
+	.platdata_auto_alloc_size = sizeof(struct sti_pinctrl_platdata),
+	.ops = &sti_pinctrl_ops,
+};
-- 
1.9.1



More information about the U-Boot mailing list