[U-Boot] [PATCH v2 3/3] board: at91sam9260ek: clean up code
Wenyou Yang
wenyou.yang at atmel.com
Fri Feb 24 10:09:45 UTC 2017
Since the introduction of the pinctrl and clk drivers and the
device tree files, remove unneeded hard coded related code from
the board file.
Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
---
Changes in v2: None
board/atmel/at91sam9260ek/at91sam9260ek.c | 73 -------------------------------
1 file changed, 73 deletions(-)
diff --git a/board/atmel/at91sam9260ek/at91sam9260ek.c b/board/atmel/at91sam9260ek/at91sam9260ek.c
index 98193bfdc6..e1bbc93924 100644
--- a/board/atmel/at91sam9260ek/at91sam9260ek.c
+++ b/board/atmel/at91sam9260ek/at91sam9260ek.c
@@ -13,12 +13,6 @@
#include <asm/arch/at91_common.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
-#include <atmel_mci.h>
-
-#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
-# include <net.h>
-#endif
-#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -67,63 +61,8 @@ static void at91sam9260ek_nand_hw_init(void)
}
#endif
-#ifdef CONFIG_MACB
-static void at91sam9260ek_macb_hw_init(void)
-{
- struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
-
- at91_periph_clk_enable(ATMEL_ID_EMAC0);
-
- /*
- * Disable pull-up on:
- * RXDV (PA17) => PHY normal mode (not Test mode)
- * ERX0 (PA14) => PHY ADDR0
- * ERX1 (PA15) => PHY ADDR1
- * ERX2 (PA25) => PHY ADDR2
- * ERX3 (PA26) => PHY ADDR3
- * ECRS (PA28) => PHY ADDR4 => PHYADDR = 0x0
- *
- * PHY has internal pull-down
- */
- writel(pin_to_mask(AT91_PIN_PA14) |
- pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA17) |
- pin_to_mask(AT91_PIN_PA25) |
- pin_to_mask(AT91_PIN_PA26) |
- pin_to_mask(AT91_PIN_PA28),
- &pioa->pudr);
-
- at91_phy_reset();
-
- /* Re-enable pull-up */
- writel(pin_to_mask(AT91_PIN_PA14) |
- pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA17) |
- pin_to_mask(AT91_PIN_PA25) |
- pin_to_mask(AT91_PIN_PA26) |
- pin_to_mask(AT91_PIN_PA28),
- &pioa->puer);
-
- /* Initialize EMAC=MACB hardware */
- at91_macb_hw_init();
-}
-#endif
-
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(bd_t *bd)
-{
- at91_mci_hw_init();
-
- return atmel_mci_init((void *)ATMEL_BASE_MCI);
-}
-#endif
-
int board_early_init_f(void)
{
- at91_periph_clk_enable(ATMEL_ID_PIOA);
- at91_periph_clk_enable(ATMEL_ID_PIOB);
- at91_periph_clk_enable(ATMEL_ID_PIOC);
-
return 0;
}
@@ -139,9 +78,6 @@ int board_init(void)
#ifdef CONFIG_HAS_DATAFLASH
at91_spi0_hw_init((1 << 0) | (1 << 1));
#endif
-#ifdef CONFIG_MACB
- at91sam9260ek_macb_hw_init();
-#endif
return 0;
}
@@ -159,12 +95,3 @@ void reset_phy(void)
{
}
#endif
-
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x00);
-#endif
- return rc;
-}
--
2.11.0
More information about the U-Boot
mailing list