[U-Boot] [PATCH 14/20] arm: socfpga: add SPL support for Arria 10

Marek Vasut marex at denx.de
Sat Feb 25 21:43:41 UTC 2017


On 02/22/2017 10:47 AM, Ley Foon Tan wrote:
> Add SPL support for Arria 10.
> 
> Signed-off-by: Tien Fong Chee <tien.fong.chee at intel.com>
> Signed-off-by: Ley Foon Tan <ley.foon.tan at intel.com>
> ---
>  arch/arm/mach-socfpga/spl.c | 92 ++++++++++++++++++++++++++++++++++++++++++++-
>  1 file changed, 90 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/mach-socfpga/spl.c b/arch/arm/mach-socfpga/spl.c
> index fec4c7a..1299e67 100644
> --- a/arch/arm/mach-socfpga/spl.c
> +++ b/arch/arm/mach-socfpga/spl.c
> @@ -19,37 +19,55 @@
>  #include <asm/arch/sdram.h>
>  #include <asm/arch/scu.h>
>  #include <asm/arch/nic301.h>
> +#include <asm/sections.h>
> +#include <watchdog.h>
> +#include <fdtdec.h>
> +#if defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
> +#include <asm/arch/pinmux.h>
> +#endif
>  
>  DECLARE_GLOBAL_DATA_PTR;
>  
> +#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
> +#define BOOTINFO_BSEL_SHIFT	0

Wasn't this defined in the misc support patch already ?

>  static struct pl310_regs *const pl310 =
>  	(struct pl310_regs *)CONFIG_SYS_PL310_BASE;
>  static struct scu_registers *scu_regs =
>  	(struct scu_registers *)SOCFPGA_MPUSCU_ADDRESS;
>  static struct nic301_registers *nic301_regs =
>  	(struct nic301_registers *)SOCFPGA_L3REGS_ADDRESS;
> -static struct socfpga_system_manager *sysmgr_regs =
> +#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
> +#define BOOTINFO_BSEL_SHIFT	12
> +#endif
> +
> +static const struct socfpga_system_manager *sysmgr_regs =
>  	(struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
>  
>  u32 spl_boot_device(void)
>  {
>  	const u32 bsel = readl(&sysmgr_regs->bootinfo);
>  
> -	switch (bsel & 0x7) {
> +	switch ((bsel >> BOOTINFO_BSEL_SHIFT) & 0x7) {
>  	case 0x1:	/* FPGA (HPS2FPGA Bridge) */
>  		return BOOT_DEVICE_RAM;
>  	case 0x2:	/* NAND Flash (1.8V) */
>  	case 0x3:	/* NAND Flash (3.0V) */
> +#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
>  		socfpga_per_reset(SOCFPGA_RESET(NAND), 0);
> +#endif
>  		return BOOT_DEVICE_NAND;
>  	case 0x4:	/* SD/MMC External Transceiver (1.8V) */
>  	case 0x5:	/* SD/MMC Internal Transceiver (3.0V) */
> +#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
>  		socfpga_per_reset(SOCFPGA_RESET(SDMMC), 0);
>  		socfpga_per_reset(SOCFPGA_RESET(DMA), 0);
> +#endif
>  		return BOOT_DEVICE_MMC1;
>  	case 0x6:	/* QSPI Flash (1.8V) */
>  	case 0x7:	/* QSPI Flash (3.0V) */
> +#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
>  		socfpga_per_reset(SOCFPGA_RESET(QSPI), 0);
> +#endif

This looks awful, you might want to split this function into
A10-specific and Gen5 specific one(s) .

>  		return BOOT_DEVICE_SPI;
>  	default:
>  		printf("Invalid boot device (bsel=%08x)!\n", bsel);
> @@ -68,6 +86,7 @@ u32 spl_boot_mode(const u32 boot_device)
>  }
>  #endif
>  
> +#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
>  static void socfpga_nic301_slave_ns(void)
>  {
>  	writel(0x1, &nic301_regs->lwhps2fpgaregs);
> @@ -182,3 +201,72 @@ void board_init_f(ulong dummy)
>  	/* Configure simple malloc base pointer into RAM. */
>  	gd->malloc_base = CONFIG_SYS_TEXT_BASE + (1024 * 1024);
>  }
> +#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
> +#ifdef CONFIG_SPL_BOARD_INIT
> +void spl_board_init(void)
> +{
> +	/* configuring the clock based on handoff */
> +	cm_basic_init(gd->fdt_blob);
> +	WATCHDOG_RESET();
> +
> +	config_dedicated_pins(gd->fdt_blob);
> +	WATCHDOG_RESET();
> +
> +	/* Release UART from reset */
> +	reset_deassert_uart();
> +
> +	/* enable console uart printing */
> +	preloader_console_init();
> +}
> +#endif
> +
> +void board_init_f(ulong dummy)
> +{
> +	memset(__bss_start, 0, __bss_end - __bss_start);

Is this really needed ? Should be done by common code already ...

> +	/*
> +	 * Configure Clock Manager to use intosc clock instead external osc to
> +	 * ensure success watchdog operation. We do it as early as possible.
> +	 */
> +	cm_use_intosc();
> +
> +	watchdog_disable();
> +
> +	arch_early_init_r();
> +
> +#ifdef CONFIG_HW_WATCHDOG
> +	/* release osc1 watchdog timer 0 from reset */
> +	reset_deassert_osc1wd0();
> +
> +	/* reconfigure and enable the watchdog */
> +	hw_watchdog_init();
> +	WATCHDOG_RESET();
> +#endif /* CONFIG_HW_WATCHDOG */
> +
> +#ifdef CONFIG_OF_CONTROL
> +	/* We need to access to FDT as this stage */
> +	/* FDT is at end of image */
> +	gd->fdt_blob = (void *)(__bss_end);

This looks like common code too ?

> +	/* Check whether we have a valid FDT or not. */
> +	if (fdtdec_prepare_fdt()) {
> +		panic("** CONFIG_OF_CONTROL defined but no FDT - please see "
> +			"doc/README.fdt-control");
> +	}
> +#endif /* CONFIG_OF_CONTROL */
> +
> +	/* Initialize the timer */
> +	timer_init();
> +
> +	/* configuring the clock based on handoff */
> +	cm_basic_init(gd->fdt_blob);
> +	WATCHDOG_RESET();
> +
> +	config_dedicated_pins(gd->fdt_blob);
> +	WATCHDOG_RESET();
> +
> +	/* Release UART from reset */
> +	reset_deassert_uart();
> +
> +	/* enable console uart printing */
> +	preloader_console_init();
> +}
> +#endif
> 


-- 
Best regards,
Marek Vasut


More information about the U-Boot mailing list