[U-Boot] [PATCH 9/9] ARM: uniphier: move SBC and Support Card init code to U-Boot proper
Masahiro Yamada
yamada.masahiro at socionext.com
Sun Jan 15 06:59:10 CET 2017
Initialize SBC and Support Card in U-Boot proper instead of SPL.
We may run different firmware (ex. ARM Trusted Firmware) before
U-Boot, and basic SoC initialization may be done there. In that
case, SPL may not be used.
The motivation for preparing SBC and Support Card in SPL was to use
LED for early debugging, but this is not mandatory to boot SoCs.
With this commit, LED will be unavailable in SPL, but we can use a
debug serial instead. So, this change will not be a big deal.
Signed-off-by: Masahiro Yamada <yamada.masahiro at socionext.com>
---
arch/arm/mach-uniphier/Makefile | 6 +++---
arch/arm/mach-uniphier/board_init.c | 16 ++++++++++++++++
arch/arm/mach-uniphier/spl_board_init.c | 24 ------------------------
3 files changed, 19 insertions(+), 27 deletions(-)
diff --git a/arch/arm/mach-uniphier/Makefile b/arch/arm/mach-uniphier/Makefile
index 7f1abd0..ab2c6dc 100644
--- a/arch/arm/mach-uniphier/Makefile
+++ b/arch/arm/mach-uniphier/Makefile
@@ -7,7 +7,6 @@ ifdef CONFIG_SPL_BUILD
obj-y += spl_board_init.o
obj-y += memconf.o
obj-y += bcu/
-obj-$(CONFIG_MICRO_SUPPORT_CARD) += sbc/
else
@@ -17,6 +16,9 @@ obj-y += board_init.o
obj-$(CONFIG_BOARD_LATE_INIT) += board_late_init.o
obj-y += reset.o
+obj-$(CONFIG_MICRO_SUPPORT_CARD) += sbc/ micro-support-card.o
+obj-y += pinctrl-glue.o
+
endif
obj-y += boards.o
@@ -24,9 +26,7 @@ obj-y += soc_info.o
obj-y += boot-mode/
obj-y += clk/
obj-y += dram/
-obj-y += pinctrl-glue.o
-obj-$(CONFIG_MICRO_SUPPORT_CARD) += micro-support-card.o
obj-$(CONFIG_DEBUG_UART_UNIPHIER) += debug-uart/
obj-$(CONFIG_CPU_V7) += arm32/
diff --git a/arch/arm/mach-uniphier/board_init.c b/arch/arm/mach-uniphier/board_init.c
index 77f1fb0..3bd4cdd 100644
--- a/arch/arm/mach-uniphier/board_init.c
+++ b/arch/arm/mach-uniphier/board_init.c
@@ -81,6 +81,7 @@ static void uniphier_ld20_misc_init(void)
struct uniphier_initdata {
enum uniphier_soc_id soc_id;
bool nand_2cs;
+ void (*sbc_init)(void);
void (*pll_init)(void);
void (*clk_init)(void);
void (*misc_init)(void);
@@ -91,6 +92,7 @@ struct uniphier_initdata uniphier_initdata[] = {
{
.soc_id = SOC_UNIPHIER_SLD3,
.nand_2cs = true,
+ .sbc_init = uniphier_sbc_init_admulti,
.pll_init = uniphier_sld3_pll_init,
.clk_init = uniphier_ld4_clk_init,
},
@@ -99,6 +101,7 @@ struct uniphier_initdata uniphier_initdata[] = {
{
.soc_id = SOC_UNIPHIER_LD4,
.nand_2cs = true,
+ .sbc_init = uniphier_ld4_sbc_init,
.pll_init = uniphier_ld4_pll_init,
.clk_init = uniphier_ld4_clk_init,
},
@@ -107,6 +110,7 @@ struct uniphier_initdata uniphier_initdata[] = {
{
.soc_id = SOC_UNIPHIER_PRO4,
.nand_2cs = false,
+ .sbc_init = uniphier_sbc_init_savepin,
.pll_init = uniphier_pro4_pll_init,
.clk_init = uniphier_pro4_clk_init,
},
@@ -115,6 +119,7 @@ struct uniphier_initdata uniphier_initdata[] = {
{
.soc_id = SOC_UNIPHIER_SLD8,
.nand_2cs = true,
+ .sbc_init = uniphier_ld4_sbc_init,
.pll_init = uniphier_ld4_pll_init,
.clk_init = uniphier_ld4_clk_init,
},
@@ -123,6 +128,7 @@ struct uniphier_initdata uniphier_initdata[] = {
{
.soc_id = SOC_UNIPHIER_PRO5,
.nand_2cs = true,
+ .sbc_init = uniphier_sbc_init_savepin,
.clk_init = uniphier_pro5_clk_init,
},
#endif
@@ -130,6 +136,7 @@ struct uniphier_initdata uniphier_initdata[] = {
{
.soc_id = SOC_UNIPHIER_PXS2,
.nand_2cs = true,
+ .sbc_init = uniphier_pxs2_sbc_init,
.clk_init = uniphier_pxs2_clk_init,
},
#endif
@@ -137,6 +144,7 @@ struct uniphier_initdata uniphier_initdata[] = {
{
.soc_id = SOC_UNIPHIER_LD6B,
.nand_2cs = true,
+ .sbc_init = uniphier_pxs2_sbc_init,
.clk_init = uniphier_pxs2_clk_init,
},
#endif
@@ -144,6 +152,7 @@ struct uniphier_initdata uniphier_initdata[] = {
{
.soc_id = SOC_UNIPHIER_LD11,
.nand_2cs = false,
+ .sbc_init = uniphier_ld11_sbc_init,
.pll_init = uniphier_ld11_pll_init,
.clk_init = uniphier_ld11_clk_init,
.misc_init = uniphier_ld11_misc_init,
@@ -153,6 +162,7 @@ struct uniphier_initdata uniphier_initdata[] = {
{
.soc_id = SOC_UNIPHIER_LD20,
.nand_2cs = false,
+ .sbc_init = uniphier_ld11_sbc_init,
.pll_init = uniphier_ld20_pll_init,
.clk_init = uniphier_ld20_clk_init,
.misc_init = uniphier_ld20_misc_init,
@@ -188,6 +198,12 @@ int board_init(void)
return -EINVAL;
}
+ initdata->sbc_init();
+
+ support_card_init();
+
+ led_puts("U0");
+
if (IS_ENABLED(CONFIG_NAND_DENALI)) {
ret = uniphier_pin_init(initdata->nand_2cs ?
"nand2cs_grp" : "nand_grp");
diff --git a/arch/arm/mach-uniphier/spl_board_init.c b/arch/arm/mach-uniphier/spl_board_init.c
index d1e1ea7..f4e1cb9 100644
--- a/arch/arm/mach-uniphier/spl_board_init.c
+++ b/arch/arm/mach-uniphier/spl_board_init.c
@@ -17,7 +17,6 @@ struct uniphier_spl_initdata {
enum uniphier_soc_id soc_id;
void (*bcu_init)(const struct uniphier_board_data *bd);
void (*early_clk_init)(void);
- void (*sbc_init)(void);
int (*dpll_init)(const struct uniphier_board_data *bd);
int (*memconf_init)(const struct uniphier_board_data *bd);
void (*dram_clk_init)(void);
@@ -30,7 +29,6 @@ static const struct uniphier_spl_initdata uniphier_spl_initdata[] = {
.soc_id = SOC_UNIPHIER_SLD3,
.bcu_init = uniphier_sld3_bcu_init,
.early_clk_init = uniphier_sld3_early_clk_init,
- .sbc_init = uniphier_sbc_init_admulti,
.dpll_init = uniphier_sld3_dpll_init,
.memconf_init = uniphier_memconf_3ch_no_disbit_init,
.dram_clk_init = uniphier_sld3_dram_clk_init,
@@ -42,7 +40,6 @@ static const struct uniphier_spl_initdata uniphier_spl_initdata[] = {
.soc_id = SOC_UNIPHIER_LD4,
.bcu_init = uniphier_ld4_bcu_init,
.early_clk_init = uniphier_sld3_early_clk_init,
- .sbc_init = uniphier_ld4_sbc_init,
.dpll_init = uniphier_ld4_dpll_init,
.memconf_init = uniphier_memconf_2ch_init,
.dram_clk_init = uniphier_sld3_dram_clk_init,
@@ -53,7 +50,6 @@ static const struct uniphier_spl_initdata uniphier_spl_initdata[] = {
{
.soc_id = SOC_UNIPHIER_PRO4,
.early_clk_init = uniphier_sld3_early_clk_init,
- .sbc_init = uniphier_sbc_init_savepin,
.dpll_init = uniphier_pro4_dpll_init,
.memconf_init = uniphier_memconf_2ch_init,
.dram_clk_init = uniphier_sld3_dram_clk_init,
@@ -65,7 +61,6 @@ static const struct uniphier_spl_initdata uniphier_spl_initdata[] = {
.soc_id = SOC_UNIPHIER_SLD8,
.bcu_init = uniphier_ld4_bcu_init,
.early_clk_init = uniphier_sld3_early_clk_init,
- .sbc_init = uniphier_ld4_sbc_init,
.dpll_init = uniphier_sld8_dpll_init,
.memconf_init = uniphier_memconf_2ch_init,
.dram_clk_init = uniphier_sld3_dram_clk_init,
@@ -76,7 +71,6 @@ static const struct uniphier_spl_initdata uniphier_spl_initdata[] = {
{
.soc_id = SOC_UNIPHIER_PRO5,
.early_clk_init = uniphier_sld3_early_clk_init,
- .sbc_init = uniphier_sbc_init_savepin,
.dpll_init = uniphier_pro5_dpll_init,
.memconf_init = uniphier_memconf_2ch_init,
.dram_clk_init = uniphier_pro5_dram_clk_init,
@@ -87,7 +81,6 @@ static const struct uniphier_spl_initdata uniphier_spl_initdata[] = {
{
.soc_id = SOC_UNIPHIER_PXS2,
.early_clk_init = uniphier_sld3_early_clk_init,
- .sbc_init = uniphier_pxs2_sbc_init,
.dpll_init = uniphier_pxs2_dpll_init,
.memconf_init = uniphier_memconf_3ch_init,
.dram_clk_init = uniphier_pxs2_dram_clk_init,
@@ -98,7 +91,6 @@ static const struct uniphier_spl_initdata uniphier_spl_initdata[] = {
{
.soc_id = SOC_UNIPHIER_LD6B,
.early_clk_init = uniphier_sld3_early_clk_init,
- .sbc_init = uniphier_pxs2_sbc_init,
.dpll_init = uniphier_pxs2_dpll_init,
.memconf_init = uniphier_memconf_3ch_init,
.dram_clk_init = uniphier_pxs2_dram_clk_init,
@@ -109,7 +101,6 @@ static const struct uniphier_spl_initdata uniphier_spl_initdata[] = {
{
.soc_id = SOC_UNIPHIER_LD11,
.early_clk_init = uniphier_ld11_early_clk_init,
- .sbc_init = uniphier_ld11_sbc_init,
.dpll_init = uniphier_ld11_dpll_init,
.memconf_init = uniphier_memconf_2ch_init,
.dram_clk_init = uniphier_ld11_dram_clk_init,
@@ -120,7 +111,6 @@ static const struct uniphier_spl_initdata uniphier_spl_initdata[] = {
{
.soc_id = SOC_UNIPHIER_LD20,
.early_clk_init = uniphier_ld11_early_clk_init,
- .sbc_init = uniphier_ld11_sbc_init,
.dpll_init = uniphier_ld20_dpll_init,
.memconf_init = uniphier_memconf_3ch_init,
.dram_clk_init = uniphier_ld20_dram_clk_init,
@@ -165,45 +155,31 @@ void spl_board_init(void)
if (initdata->bcu_init)
initdata->bcu_init(bd);
- initdata->sbc_init();
initdata->early_clk_init();
- support_card_init();
-
- led_puts("L0");
#ifdef CONFIG_SPL_SERIAL_SUPPORT
preloader_console_init();
#endif
- led_puts("L1");
-
ret = initdata->dpll_init(bd);
if (ret) {
pr_err("failed to init DPLL\n");
hang();
}
- led_puts("L2");
-
ret = initdata->memconf_init(bd);
if (ret) {
pr_err("failed to init MEMCONF\n");
hang();
}
- led_puts("L3");
-
initdata->dram_clk_init();
- led_puts("L4");
-
ret = initdata->umc_init(bd);
if (ret) {
pr_err("failed to init DRAM\n");
hang();
}
-
- led_puts("L5");
}
--
2.7.4
More information about the U-Boot
mailing list