[U-Boot] [PATCH v2 2/2] board/chiliboard: Add support for chiliBoard
Marcin Niestroj
m.niestroj at grinn-global.com
Tue Jan 24 18:51:52 CET 2017
chiliBoard is a development board which uses chiliSOM as its base.
Hardware specification:
* chiliSOM (TI AM335x, DRAM, NAND)
* Ethernet PHY (id 0)
* USB host (usb1)
* MicroSD slot (mmc0)
Signed-off-by: Marcin Niestroj <m.niestroj at grinn-global.com>
---
Changes v1 -> v2:
* converted include/configs/chiliboard.h header to SPDX license
identifier (suggested by Tom)
* removed USB gadget, CMD_DFU options from chiliboard_defconfig
arch/arm/Kconfig | 1 +
arch/arm/mach-omap2/am33xx/Kconfig | 6 +
board/grinn/chiliboard/Kconfig | 15 +++
board/grinn/chiliboard/MAINTAINERS | 6 +
board/grinn/chiliboard/Makefile | 6 +
board/grinn/chiliboard/README | 31 +++++
board/grinn/chiliboard/board.c | 264 +++++++++++++++++++++++++++++++++++++
configs/chiliboard_defconfig | 48 +++++++
include/configs/chiliboard.h | 220 +++++++++++++++++++++++++++++++
9 files changed, 597 insertions(+)
create mode 100644 board/grinn/chiliboard/Kconfig
create mode 100644 board/grinn/chiliboard/MAINTAINERS
create mode 100644 board/grinn/chiliboard/Makefile
create mode 100644 board/grinn/chiliboard/README
create mode 100644 board/grinn/chiliboard/board.c
create mode 100644 configs/chiliboard_defconfig
create mode 100644 include/configs/chiliboard.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 2554a2cd14..3421f273b5 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1046,6 +1046,7 @@ source "board/freescale/mx53loco/Kconfig"
source "board/freescale/mx53smd/Kconfig"
source "board/freescale/s32v234evb/Kconfig"
source "board/freescale/vf610twr/Kconfig"
+source "board/grinn/chiliboard/Kconfig"
source "board/gumstix/pepper/Kconfig"
source "board/h2200/Kconfig"
source "board/hisilicon/hikey/Kconfig"
diff --git a/arch/arm/mach-omap2/am33xx/Kconfig b/arch/arm/mach-omap2/am33xx/Kconfig
index b1a0f0f356..57e1a93211 100644
--- a/arch/arm/mach-omap2/am33xx/Kconfig
+++ b/arch/arm/mach-omap2/am33xx/Kconfig
@@ -59,6 +59,12 @@ config TARGET_BAV335X
For more information, visit: http://birdland.com/oem
+config TARGET_CHILIBOARD
+ bool "Grinn chiliBoard"
+ select AM33XX_CHILISOM
+ select DM
+ select DM_SERIAL
+
config TARGET_CM_T335
bool "Support cm_t335"
select DM
diff --git a/board/grinn/chiliboard/Kconfig b/board/grinn/chiliboard/Kconfig
new file mode 100644
index 0000000000..20056e81a1
--- /dev/null
+++ b/board/grinn/chiliboard/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_CHILIBOARD
+
+config SYS_BOARD
+ default "chiliboard"
+
+config SYS_VENDOR
+ default "grinn"
+
+config SYS_CONFIG_NAME
+ default "chiliboard"
+
+config SYS_SOC
+ default "am33xx"
+
+endif
diff --git a/board/grinn/chiliboard/MAINTAINERS b/board/grinn/chiliboard/MAINTAINERS
new file mode 100644
index 0000000000..56b306f84c
--- /dev/null
+++ b/board/grinn/chiliboard/MAINTAINERS
@@ -0,0 +1,6 @@
+CHILIBOARD
+M: Marcin Niestroj <m.niestroj at grinn-global.com>
+S: Maintained
+F: board/grinn/chiliboard/
+F: include/configs/chiliboard.h
+F: configs/chiliboard_defconfig
diff --git a/board/grinn/chiliboard/Makefile b/board/grinn/chiliboard/Makefile
new file mode 100644
index 0000000000..865968d1a7
--- /dev/null
+++ b/board/grinn/chiliboard/Makefile
@@ -0,0 +1,6 @@
+# (C) Copyright 2017 Grinn
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := board.o
diff --git a/board/grinn/chiliboard/README b/board/grinn/chiliboard/README
new file mode 100644
index 0000000000..cea4c1d42e
--- /dev/null
+++ b/board/grinn/chiliboard/README
@@ -0,0 +1,31 @@
+How to use U-Boot on Grinn's chiliBoard
+--------------------------------------
+
+- Build U-Boot for chiliBoard:
+
+$ make mrproper
+$ make chiliboard_defconfig
+$ make
+
+This will generate the SPL image called MLO and the u-boot.img.
+
+- Flash the SPL image into the micro SD card:
+
+sudo dd if=MLO of=/dev/mmcblk0 bs=128k; sync
+
+- Flash the u-boot.img image into the micro SD card:
+
+sudo dd if=u-boot.img of=/dev/mmcblk0 bs=128k seek=3; sync
+
+- Jumper settings:
+
+S2: 1 1 1 0 1 0
+
+where 0 means bottom position and 1 means top position (from the
+switch label numbers reference).
+
+- Insert the micro SD card in the board.
+
+- Connect USB cable between chiliBoard and the PC for the power and console.
+
+- U-Boot messages should come up.
diff --git a/board/grinn/chiliboard/board.c b/board/grinn/chiliboard/board.c
new file mode 100644
index 0000000000..b0015f1663
--- /dev/null
+++ b/board/grinn/chiliboard/board.c
@@ -0,0 +1,264 @@
+/*
+ * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ * Copyright (C) 2017, Grinn - http://grinn-global.com/
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/chilisom.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/emif.h>
+#include <asm/io.h>
+#include <cpsw.h>
+#include <environment.h>
+#include <errno.h>
+#include <miiphy.h>
+#include <serial.h>
+#include <spl.h>
+#include <watchdog.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static __maybe_unused struct ctrl_dev *cdev =
+ (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+static struct module_pin_mux uart0_pin_mux[] = {
+ {OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* UART0_RXD */
+ {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, /* UART0_TXD */
+ {-1},
+};
+
+static struct module_pin_mux mmc0_pin_mux[] = {
+ {OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT3 */
+ {OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT2 */
+ {OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT1 */
+ {OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT0 */
+ {OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CLK */
+ {OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CMD */
+ {-1},
+};
+
+static struct module_pin_mux rmii1_pin_mux[] = {
+ {OFFSET(mii1_crs), MODE(1) | RXACTIVE}, /* RMII1_CRS */
+ {OFFSET(mii1_rxerr), MODE(1) | RXACTIVE}, /* RMII1_RXERR */
+ {OFFSET(mii1_txen), MODE(1)}, /* RMII1_TXEN */
+ {OFFSET(mii1_txd1), MODE(1)}, /* RMII1_TXD1 */
+ {OFFSET(mii1_txd0), MODE(1)}, /* RMII1_TXD0 */
+ {OFFSET(mii1_rxd1), MODE(1) | RXACTIVE}, /* RMII1_RXD1 */
+ {OFFSET(mii1_rxd0), MODE(1) | RXACTIVE}, /* RMII1_RXD0 */
+ {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */
+ {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */
+ {OFFSET(rmii1_refclk), MODE(0) | RXACTIVE}, /* RMII1_REFCLK */
+ {-1},
+};
+
+static void enable_board_pin_mux(void)
+{
+ chilisom_enable_pin_mux();
+
+ /* chiliboard pinmux */
+ configure_module_pin_mux(rmii1_pin_mux);
+ configure_module_pin_mux(mmc0_pin_mux);
+}
+#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
+
+#ifndef CONFIG_DM_SERIAL
+struct serial_device *default_serial_console(void)
+{
+ return &eserial1_device;
+}
+#endif
+
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+void set_uart_mux_conf(void)
+{
+ configure_module_pin_mux(uart0_pin_mux);
+}
+
+void set_mux_conf_regs(void)
+{
+ enable_board_pin_mux();
+}
+
+void am33xx_spl_board_init(void)
+{
+ chilisom_spl_board_init();
+}
+#endif
+
+/*
+ * Basic board specific setup. Pinmux has been handled already.
+ */
+int board_init(void)
+{
+#if defined(CONFIG_HW_WATCHDOG)
+ hw_watchdog_init();
+#endif
+
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+ gpmc_init();
+
+ return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+#if !defined(CONFIG_SPL_BUILD)
+ uint8_t mac_addr[6];
+ uint32_t mac_hi, mac_lo;
+
+ /* try reading mac address from efuse */
+ mac_lo = readl(&cdev->macid0l);
+ mac_hi = readl(&cdev->macid0h);
+ mac_addr[0] = mac_hi & 0xFF;
+ mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+ mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+ mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+ mac_addr[4] = mac_lo & 0xFF;
+ mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+ if (!getenv("ethaddr")) {
+ printf("<ethaddr> not set. Validating first E-fuse MAC\n");
+
+ if (is_valid_ethaddr(mac_addr))
+ eth_setenv_enetaddr("ethaddr", mac_addr);
+ }
+
+ mac_lo = readl(&cdev->macid1l);
+ mac_hi = readl(&cdev->macid1h);
+ mac_addr[0] = mac_hi & 0xFF;
+ mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+ mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+ mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+ mac_addr[4] = mac_lo & 0xFF;
+ mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+ if (!getenv("eth1addr")) {
+ if (is_valid_ethaddr(mac_addr))
+ eth_setenv_enetaddr("eth1addr", mac_addr);
+ }
+#endif
+
+ return 0;
+}
+#endif
+
+#ifndef CONFIG_DM_ETH
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+ (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+static void cpsw_control(int enabled)
+{
+ /* VTP can be added here */
+
+ return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+ {
+ .slave_reg_ofs = 0x208,
+ .sliver_reg_ofs = 0xd80,
+ .phy_addr = 0,
+ }
+};
+
+static struct cpsw_platform_data cpsw_data = {
+ .mdio_base = CPSW_MDIO_BASE,
+ .cpsw_base = CPSW_BASE,
+ .mdio_div = 0xff,
+ .channels = 8,
+ .cpdma_reg_ofs = 0x800,
+ .slaves = 1,
+ .slave_data = cpsw_slaves,
+ .ale_reg_ofs = 0xd00,
+ .ale_entries = 1024,
+ .host_port_reg_ofs = 0x108,
+ .hw_stats_reg_ofs = 0x900,
+ .bd_ram_ofs = 0x2000,
+ .mac_control = (1 << 5),
+ .control = cpsw_control,
+ .host_port_num = 0,
+ .version = CPSW_CTRL_VERSION_2,
+};
+#endif
+
+#if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USBETH_SUPPORT)) &&\
+ defined(CONFIG_SPL_BUILD)) || \
+ ((defined(CONFIG_DRIVER_TI_CPSW) || \
+ defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)) && \
+ !defined(CONFIG_SPL_BUILD))
+
+/*
+ * This function will:
+ * Read the eFuse for MAC addresses, and set ethaddr/eth1addr/usbnet_devaddr
+ * in the environment
+ * Perform fixups to the PHY present on certain boards. We only need this
+ * function in:
+ * - SPL with either CPSW or USB ethernet support
+ * - Full U-Boot, with either CPSW or USB ethernet
+ * Build in only these cases to avoid warnings about unused variables
+ * when we build an SPL that has neither option but full U-Boot will.
+ */
+int board_eth_init(bd_t *bis)
+{
+ int rv, n = 0;
+#if defined(CONFIG_USB_ETHER) && \
+ (!defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_USBETH_SUPPORT))
+ uint8_t mac_addr[6];
+ uint32_t mac_hi, mac_lo;
+
+ /*
+ * use efuse mac address for USB ethernet as we know that
+ * both CPSW and USB ethernet will never be active at the same time
+ */
+ mac_lo = readl(&cdev->macid0l);
+ mac_hi = readl(&cdev->macid0h);
+ mac_addr[0] = mac_hi & 0xFF;
+ mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+ mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+ mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+ mac_addr[4] = mac_lo & 0xFF;
+ mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+#endif
+
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+ (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+ writel(RMII_MODE_ENABLE | RMII_CHIPCKL_ENABLE, &cdev->miisel);
+ cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_RMII;
+
+ rv = cpsw_register(&cpsw_data);
+ if (rv < 0)
+ printf("Error %d registering CPSW switch\n", rv);
+ else
+ n += rv;
+#endif
+#endif
+
+#if defined(CONFIG_USB_ETHER) && \
+ (!defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_USBETH_SUPPORT))
+ if (is_valid_ethaddr(mac_addr))
+ eth_setenv_enetaddr("usbnet_devaddr", mac_addr);
+
+ rv = usb_eth_initialize(bis);
+ if (rv < 0)
+ printf("Error %d registering USB_ETHER\n", rv);
+ else
+ n += rv;
+#endif
+ return n;
+}
+#endif
+
+#endif /* CONFIG_DM_ETH */
diff --git a/configs/chiliboard_defconfig b/configs/chiliboard_defconfig
new file mode 100644
index 0000000000..08fb7eed4e
--- /dev/null
+++ b/configs/chiliboard_defconfig
@@ -0,0 +1,48 @@
+CONFIG_ARM=y
+CONFIG_AM33XX=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SPL_FAT_SUPPORT=y
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_NAND_SUPPORT=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_TARGET_CHILIBOARD=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_SPL_STACK_R_ADDR=0x82000000
+CONFIG_FIT=y
+CONFIG_BOOTDELAY=1
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+CONFIG_BOARD_LATE_INIT=y
+CONFIG_SPL=y
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_MUSB_NEW_SUPPORT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_ASKENV=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_DM_GPIO=y
+CONFIG_MMC_OMAP_HS=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_SYS_NS16550=y
+CONFIG_USB=y
+CONFIG_USB_MUSB_HOST=y
+CONFIG_USB_STORAGE=y
+CONFIG_OF_LIBFDT=y
diff --git a/include/configs/chiliboard.h b/include/configs/chiliboard.h
new file mode 100644
index 0000000000..4abe38035b
--- /dev/null
+++ b/include/configs/chiliboard.h
@@ -0,0 +1,220 @@
+/*
+ * Copyright (C) 2017 Grinn - http://grinn-global.com/
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_CHILIBOARD_H
+#define __CONFIG_CHILIBOARD_H
+
+#define CONFIG_NAND
+
+#include <configs/ti_am335x_common.h>
+
+#define CONFIG_CONS_INDEX 1
+
+#ifndef CONFIG_SPL_BUILD
+# define CONFIG_TIMESTAMP
+# define CONFIG_LZO
+#endif
+
+/* Clock Defines */
+#define V_OSCK 24000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK)
+
+#define NANDARGS \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "nandargs=setenv bootargs console=${console} ${optargs} " \
+ "${mtdparts} " \
+ "root=${nandroot} " \
+ "rootfstype=${nandrootfstype}\0" \
+ "nandroot=ubi0:rootfs rw ubi.mtd=NAND.file-system\0" \
+ "nandrootfstype=ubifs rootwait=1\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${fdt_addr} NAND.u-boot-spl-os; " \
+ "nand read ${loadaddr} NAND.kernel; " \
+ "bootz ${loadaddr} - ${fdt_addr}\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "run mmcboot; " \
+ "run nandboot; " \
+ "run netboot"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x82000000\0" \
+ "fdt_addr=0x87800000\0" \
+ "boot_fdt=try\0" \
+ "console=ttyO0,115200n8\0" \
+ "image=zImage\0" \
+ "fdt_file=am335x-chiliboard.dtb\0" \
+ "ip_dyn=yes\0" \
+ "optargs=\0" \
+ "loadbootscript=" \
+ "load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
+ "${boot_dir}/${image}\0" \
+ "loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} " \
+ "${boot_dir}/${fdt_file}\0" \
+ "mmcdev=0\0" \
+ "mmcpart=1\0" \
+ "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} ${optargs} " \
+ "${mtdparts} " \
+ "root=${mmcroot}\0" \
+ "mmcloados=run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi;\0" \
+ "mmcboot=mmc dev ${mmcdev}; " \
+ "if mmc rescan; then " \
+ "echo SD/MMC found on device ${mmcdev};" \
+ "if run loadimage; then " \
+ "run mmcloados;" \
+ "fi;" \
+ "fi;\0" \
+ "netargs=setenv bootargs console=${console},${baudrate} ${optargs} " \
+ "${mtdparts} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${image}; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi;\0" \
+ NANDARGS
+
+/* NS16550 Configuration */
+#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */
+#define CONFIG_SYS_NS16550_COM2 0x48022000 /* UART1 */
+#define CONFIG_SYS_NS16550_COM3 0x48024000 /* UART2 */
+#define CONFIG_SYS_NS16550_COM4 0x481a6000 /* UART3 */
+#define CONFIG_SYS_NS16550_COM5 0x481a8000 /* UART4 */
+#define CONFIG_SYS_NS16550_COM6 0x481aa000 /* UART5 */
+#define CONFIG_BAUDRATE 115200
+
+/* PMIC support */
+#define CONFIG_POWER_TPS65217
+
+/* SPL */
+/* Bootcount using the RTC block */
+#define CONFIG_BOOTCOUNT_LIMIT
+#define CONFIG_BOOTCOUNT_AM33XX
+#define CONFIG_SYS_BOOTCOUNT_BE
+
+#define CONFIG_SPL_LDSCRIPT "arch/arm/mach-omap2/am33xx/u-boot-spl.lds"
+
+/* NAND: device related configs */
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+/* NAND: driver related configs */
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_NAND_OMAP_GPMC_PREFETCH
+#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
+ 10, 11, 12, 13, 14, 15, 16, 17, \
+ 18, 19, 20, 21, 22, 23, 24, 25, \
+ 26, 27, 28, 29, 30, 31, 32, 33, \
+ 34, 35, 36, 37, 38, 39, 40, 41, \
+ 42, 43, 44, 45, 46, 47, 48, 49, \
+ 50, 51, 52, 53, 54, 55, 56, 57, }
+
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 14
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
+#define MTDIDS_DEFAULT "nand0=8000000.nand"
+#define MTDPARTS_DEFAULT "mtdparts=8000000.nand:" \
+ "128k(NAND.SPL)," \
+ "128k(NAND.SPL.backup1)," \
+ "128k(NAND.SPL.backup2)," \
+ "128k(NAND.SPL.backup3)," \
+ "256k(NAND.u-boot-spl-os)," \
+ "1m(NAND.u-boot)," \
+ "128k(NAND.u-boot-env)," \
+ "128k(NAND.u-boot-env.backup1)," \
+ "8m(NAND.kernel)," \
+ "-(NAND.file-system)"
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x000c0000
+/* NAND: SPL related configs */
+#ifdef CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_AM33XX_BCH
+#endif
+
+/* USB configuration */
+#define CONFIG_USB_MUSB_DSPS
+#define CONFIG_ARCH_MISC_INIT
+#define CONFIG_USB_MUSB_PIO_ONLY
+#define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT
+#define CONFIG_AM335X_USB1
+#define CONFIG_AM335X_USB1_MODE MUSB_HOST
+
+/*
+ * Disable MMC DM for SPL build and can be re-enabled after adding
+ * DM support in SPL
+ */
+#ifdef CONFIG_SPL_BUILD
+#undef CONFIG_DM_MMC
+#undef CONFIG_TIMER
+#undef CONFIG_DM_USB
+#endif
+
+#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_USBETH_SUPPORT)
+/* Remove other SPL modes. */
+#define CONFIG_ENV_IS_NOWHERE
+#undef CONFIG_ENV_IS_IN_NAND
+#endif
+
+#if defined(CONFIG_ENV_IS_IN_NAND)
+#define CONFIG_ENV_OFFSET 0x001c0000
+#define CONFIG_ENV_OFFSET_REDUND 0x001e0000
+#define CONFIG_ENV_SIZE SZ_128K
+#define CONFIG_SYS_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#else
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_OFFSET SZ_128K
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE SZ_8K
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#endif
+
+/* Network. */
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_SMSC
+
+#endif /* ! __CONFIG_CHILIBOARD_H */
--
2.11.0
More information about the U-Boot
mailing list