[U-Boot] [PATCH v4 5/9] arm: dts: imx6ul-isiot: Add FEC node

[Stefano Babic]

On 27/01/2017 09:54, Jagan Teki wrote:
> From: Jagan Teki <jagan at amarulasolutions.com>
> 
> Add FEC node for Engicam Is.IoT MX6UL module.
> 
> Cc: Stefano Babic <sbabic at denx.de>
> Cc: Matteo Lisi <matteo.lisi at engicam.com>
> Cc: Michael Trimarchi <michael at amarulasolutions.com>
> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
> ---
>  arch/arm/dts/imx6ul-isiot.dtsi | 22 ++++++++++++++++++++++
>  1 file changed, 22 insertions(+)
> 
> diff --git a/arch/arm/dts/imx6ul-isiot.dtsi b/arch/arm/dts/imx6ul-isiot.dtsi
> index 1a474ca..346079a 100644
> --- a/arch/arm/dts/imx6ul-isiot.dtsi
> +++ b/arch/arm/dts/imx6ul-isiot.dtsi
> @@ -56,6 +56,13 @@
>  	};
>  };
>  
> +&fec1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_enet1>;
> +	phy-mode = "rmii";
> +	status = "okay";
> +};
> +
>  &i2c1 {
>  	clock-frequency = <100000>;
>  	pinctrl-names = "default";
> @@ -86,6 +93,21 @@
>  };
>  
>  &iomuxc {
> +	pinctrl_enet1: enet1grp {
> +		fsl,pins = <
> +			MX6UL_PAD_ENET2_RX_DATA0__ENET1_MDIO    0x1b0b0
> +			MX6UL_PAD_ENET2_RX_DATA1__ENET1_MDC     0x1b0b0
> +			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN      0x1b0b0
> +			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
> +			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
> +			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN      0x1b0b0
> +			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
> +			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
> +			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1  0x4001b031
> +			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10       0x1b0b0
> +		>;
> +	};
> +
>  	pinctrl_i2c1: i2c1grp {
>  		fsl,pins = <
>  			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
> 
Reviewed-by: Stefano Babic <sbabic at denx.de>

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================