[U-Boot] [PATCH 10/16] ARM: uniphier: use Image.gz instead Image for booting ARM64 Linux

[Masahiro Yamada]

The ARM64 Linux raw image now amounts to 15MB and it is getting
bigger and bigger.  Using Image.gz saves about 8MB.  The cost of
unzip is smaller than what we get by saving the kernel loading
from non-volatile devices.

The ARM32 Linux still uses zImage, a self-decompressor image,
so it should not be affected.

Signed-off-by: Masahiro Yamada <yamada.masahiro at socionext.com>
---

 include/configs/uniphier.h | 36 ++++++++++++++++++++++--------------
 1 file changed, 22 insertions(+), 14 deletions(-)

diff --git a/include/configs/uniphier.h b/include/configs/uniphier.h
index 94d87c3..b6dc76e 100644
--- a/include/configs/uniphier.h
+++ b/include/configs/uniphier.h
@@ -15,6 +15,10 @@
 
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  10
 
+#ifdef CONFIG_ARM64
+#define CONFIG_CMD_UNZIP
+#endif
+
 /*-----------------------------------------------------------------------
  * MMU and Cache Setting
  *----------------------------------------------------------------------*/
@@ -167,46 +171,50 @@
 	"__nfsboot=run tftpboot\0"
 #else
 #ifdef CONFIG_ARM64
-#define CONFIG_BOOTFILE			"Image"
+#define CONFIG_BOOTFILE			"Image.gz"
 #define LINUXBOOT_CMD			"booti"
+#define KERNEL_ADDR_LOAD		"kernel_addr_load=0x84200000\0"
 #define KERNEL_ADDR_R			"kernel_addr_r=0x80080000\0"
-#define KERNEL_SIZE			"kernel_size=0x00c00000\0"
-#define RAMDISK_ADDR			"ramdisk_addr=0x00e00000\0"
 #else
 #define CONFIG_BOOTFILE			"zImage"
 #define LINUXBOOT_CMD			"bootz"
+#define KERNEL_ADDR_LOAD		"kernel_addr_load=0x80208000\0"
 #define KERNEL_ADDR_R			"kernel_addr_r=0x80208000\0"
-#define KERNEL_SIZE			"kernel_size=0x00800000\0"
-#define RAMDISK_ADDR			"ramdisk_addr=0x00a00000\0"
 #endif
 #define LINUXBOOT_ENV_SETTINGS \
 	"fdt_addr=0x00100000\0" \
 	"fdt_addr_r=0x84100000\0" \
 	"fdt_size=0x00008000\0" \
 	"kernel_addr=0x00200000\0" \
+	KERNEL_ADDR_LOAD \
 	KERNEL_ADDR_R \
-	KERNEL_SIZE \
-	RAMDISK_ADDR \
+	"kernel_size=0x00800000\0" \
+	"ramdisk_addr=0x00a00000\0" \
 	"ramdisk_addr_r=0x84a00000\0" \
 	"ramdisk_size=0x00600000\0" \
 	"ramdisk_file=rootfs.cpio.uboot\0" \
-	"boot_common=setexpr bootm_low $kernel_addr_r '&' fe000000 &&" \
+	"boot_common=setexpr bootm_low $kernel_addr_r '&' fe000000 && " \
+		"if test $kernel_addr_load = $kernel_addr_r; then " \
+			"true; " \
+		"else " \
+			"unzip $kernel_addr_load $kernel_addr_r; " \
+		"fi && " \
 		LINUXBOOT_CMD " $kernel_addr_r $ramdisk_addr_r $fdt_addr_r\0" \
-	"norboot=setexpr kernel_addr $nor_base + $kernel_addr &&" \
-		"setexpr kernel_size $kernel_size / 4 &&" \
-		"cp $kernel_addr $kernel_addr_r $kernel_size &&" \
+	"norboot=setexpr kernel_addr_nor $nor_base + $kernel_addr && " \
+		"setexpr kernel_size_div4 $kernel_size / 4 && " \
+		"cp $kernel_addr_nor $kernel_addr_load $kernel_size_div4 && " \
 		"setexpr ramdisk_addr_r $nor_base + $ramdisk_addr &&" \
 		"setexpr fdt_addr_r $nor_base + $fdt_addr &&" \
 		"run boot_common\0" \
-	"nandboot=nand read $kernel_addr_r $kernel_addr $kernel_size &&" \
+	"nandboot=nand read $kernel_addr_load $kernel_addr $kernel_size && " \
 		"nand read $ramdisk_addr_r $ramdisk_addr $ramdisk_size &&" \
 		"nand read $fdt_addr_r $fdt_addr $fdt_size &&" \
 		"run boot_common\0" \
-	"tftpboot=tftpboot $kernel_addr_r $bootfile &&" \
+	"tftpboot=tftpboot $kernel_addr_load $bootfile && " \
 		"tftpboot $ramdisk_addr_r $ramdisk_file &&" \
 		"tftpboot $fdt_addr_r $fdt_file &&" \
 		"run boot_common\0" \
-	"__nfsboot=tftpboot $kernel_addr_r $bootfile &&" \
+	"__nfsboot=tftpboot $kernel_addr_load $bootfile && " \
 		"tftpboot $fdt_addr_r $fdt_file &&" \
 		"setenv ramdisk_addr_r - &&" \
 		"run boot_common\0"
-- 
2.7.4