[U-Boot] [PATCH v2 11/15] drivers: nand: omap_gpmc: convert driver to adopt driver model
Grygorii Strashko
grygorii.strashko at ti.com
Tue Jan 31 22:37:13 CET 2017
From: Mugunthan V N <mugunthanvnm at ti.com>
adopt omap_gpmc driver to driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm at ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko at ti.com>
---
drivers/mtd/nand/omap_gpmc.c | 205 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 205 insertions(+)
diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c
index b540bc3..a2d1634 100644
--- a/drivers/mtd/nand/omap_gpmc.c
+++ b/drivers/mtd/nand/omap_gpmc.c
@@ -16,6 +16,10 @@
#include <nand.h>
#include <linux/mtd/omap_elm.h>
+#include <dm.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
#define BADBLOCK_MARKER_LENGTH 2
#define SECTOR_BYTES 512
#define ECCCLEAR (0x1 << 8)
@@ -46,11 +50,22 @@ struct omap_nand_info {
enum omap_ecc ecc_scheme;
uint8_t cs;
uint8_t ws; /* wait status pin (0,1) */
+ uint8_t bus_width; /* Bus width of NAND device */
};
+#ifndef CONFIG_DM_NAND
/* We are wasting a bit of memory but al least we are safe */
static struct omap_nand_info omap_nand_info[GPMC_MAX_CS];
+#else
+
+struct omap_gpmc_platdata {
+ struct omap_nand_info *omap_nand_info;
+ struct gpmc *gpmc_cfg;
+ int max_cs;
+};
+#endif
+
/*
* omap_nand_hwcontrol - Set the address pointers corretly for the
* following address/data/command operation
@@ -945,6 +960,8 @@ int __maybe_unused omap_nand_switch_ecc(uint32_t hardware, uint32_t eccstrength)
}
#endif /* CONFIG_SPL_BUILD */
+#ifndef CONFIG_DM_NAND
+
/*
* Board-specific NAND initialization. The following members of the
* argument are board-specific:
@@ -1036,3 +1053,191 @@ int board_nand_init(struct nand_chip *nand)
return 0;
}
+
+#else /* CONFIG_DM_NAND */
+
+static int omap_gpmc_probe(struct udevice *dev)
+{
+ struct nand_chip *nand = dev_get_priv(dev);
+ struct omap_gpmc_platdata *pdata = dev_get_platdata(dev);
+ struct gpmc *gpmc_cfg = pdata->gpmc_cfg;
+ int32_t gpmc_config = 0;
+ int ecc_opt;
+ int cs = cs_next++;
+ int err = 0;
+
+ while (cs < pdata->max_cs) {
+ /* Check if NAND type is set */
+ if ((readl(&gpmc_cfg->cs[cs].config1) & 0xC00) == 0x800) {
+ /* Found it!! */
+ break;
+ }
+ cs++;
+ }
+
+ if (cs >= pdata->max_cs) {
+ printf("nand: error: Unable to find NAND settings in GPMC Configuration - quitting\n");
+ return -ENODEV;
+ }
+
+ gpmc_config = readl(&gpmc_cfg->config);
+ /* Disable Write protect */
+ gpmc_config |= 0x10;
+ writel(gpmc_config, &gpmc_cfg->config);
+
+ nand->IO_ADDR_R = (void __iomem *)&gpmc_cfg->cs[cs].nand_dat;
+ nand->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_cmd;
+ nand->priv = &pdata->omap_nand_info[cs];
+ nand->cmd_ctrl = omap_nand_hwcontrol;
+ nand->options |= NAND_NO_PADDING | NAND_CACHEPRG;
+ nand->chip_delay = 100;
+ nand->ecc.layout = &omap_ecclayout;
+
+ /* configure driver and controller based on NAND device bus-width */
+ gpmc_config = readl(&gpmc_cfg->cs[cs].config1);
+ if (pdata->omap_nand_info[cs].bus_width == 16) {
+ nand->options |= NAND_BUSWIDTH_16;
+ writel(gpmc_config | (0x1 << 12), &gpmc_cfg->cs[cs].config1);
+ } else {
+ nand->options &= ~NAND_BUSWIDTH_16;
+ writel(gpmc_config & ~(0x1 << 12), &gpmc_cfg->cs[cs].config1);
+ }
+
+ ecc_opt = pdata->omap_nand_info[cs].ecc_scheme;
+ /* select ECC scheme */
+ if (ecc_opt != OMAP_ECC_HAM1_CODE_SW) {
+ err = omap_select_ecc_scheme(nand, ecc_opt,
+ CONFIG_SYS_NAND_PAGE_SIZE,
+ CONFIG_SYS_NAND_OOBSIZE);
+ } else {
+ /*
+ * pagesize and oobsize are not required to
+ * configure sw ecc-scheme
+ */
+ err = omap_select_ecc_scheme(nand, ecc_opt, 0, 0);
+ }
+ if (err)
+ return err;
+
+#ifdef CONFIG_NAND_OMAP_GPMC_PREFETCH
+ nand->read_buf = omap_nand_read_prefetch;
+#else
+ if (nand->options & NAND_BUSWIDTH_16)
+ nand->read_buf = nand_read_buf16;
+ else
+ nand->read_buf = nand_read_buf;
+#endif
+
+ nand->dev_ready = omap_dev_ready;
+
+ return 0;
+}
+
+static int omap_gpmc_get_ecc_opt(int node, int elm_node)
+{
+ const void *fdt = gd->fdt_blob;
+ const char *ecc_str;
+ int ecc_opt = -ENOENT;
+
+ ecc_str = fdt_getprop(fdt, node, "ti,nand-ecc-opt", NULL);
+ if (!ecc_str) {
+ error("DT entry for ti,nand-ecc-opt not found\n");
+ return -ENOENT;
+ }
+
+ if (!strcmp(ecc_str, "sw")) {
+ ecc_opt = OMAP_ECC_HAM1_CODE_SW;
+ } else if (!strcmp(ecc_str, "ham1") ||
+ !strcmp(ecc_str, "hw") ||
+ !strcmp(ecc_str, "hw-romcode")) {
+ ecc_opt = OMAP_ECC_HAM1_CODE_HW;
+ } else if (!strcmp(ecc_str, "bch4")) {
+ if (elm_node > 0)
+ ecc_opt = OMAP_ECC_BCH4_CODE_HW;
+ else
+ ecc_opt = OMAP_ECC_BCH4_CODE_HW_DETECTION_SW;
+ } else if (!strcmp(ecc_str, "bch8")) {
+ if (elm_node > 0)
+ ecc_opt = OMAP_ECC_BCH8_CODE_HW;
+ else
+ ecc_opt = OMAP_ECC_BCH8_CODE_HW_DETECTION_SW;
+ } else if (!strcmp(ecc_str, "bch16")) {
+ if (elm_node > 0)
+ ecc_opt = OMAP_ECC_BCH16_CODE_HW;
+ else
+ error("BCH16 requires ELM support\n");
+ } else {
+ error("ti,nand-ecc-opt invalid value\n");
+ return -EINVAL;
+ }
+
+ return ecc_opt;
+}
+
+static int omap_gpmc_ofdata_to_platdata(struct udevice *dev)
+{
+ struct omap_gpmc_platdata *pdata = dev_get_platdata(dev);
+ const void *fdt = gd->fdt_blob;
+ int node = dev->of_offset;
+ int subnode;
+
+ pdata->gpmc_cfg = (struct gpmc *)dev_get_addr(dev);
+ pdata->max_cs = fdtdec_get_int(fdt, node, "gpmc,num-cs", -1);
+ if (pdata->max_cs < 0) {
+ error("max chip select not found in DT\n");
+ return -ENOENT;
+ }
+
+ pdata->omap_nand_info = calloc(pdata->max_cs,
+ sizeof(struct omap_nand_info));
+ if (!pdata->omap_nand_info)
+ return -ENOMEM;
+
+ fdt_for_each_subnode(subnode, fdt, node) {
+ int cs;
+ int len;
+ int elm_node;
+ const char *name;
+ struct omap_nand_info *nand_info;
+
+ name = fdt_get_name(fdt, subnode, &len);
+ if (strncmp(name, "nand", 4))
+ continue;
+
+ cs = fdtdec_get_int(fdt, subnode, "reg", -1);
+ if (cs < 0 || cs >= pdata->max_cs) {
+ error("Invalid cs for nand device\n");
+ return -EINVAL;
+ }
+ nand_info = &pdata->omap_nand_info[cs];
+
+ /* get bus width 8 or 16, if not present 8 */
+ nand_info->bus_width = fdtdec_get_int(fdt, subnode,
+ "nand-bus-width", 8);
+
+ elm_node = fdtdec_lookup_phandle(fdt, subnode, "ti,elm-id");
+
+ nand_info->ecc_scheme = omap_gpmc_get_ecc_opt(subnode,
+ elm_node);
+ if (nand_info->ecc_scheme < 0)
+ return nand_info->ecc_scheme;
+ }
+ return 0;
+}
+
+static const struct udevice_id omap_gpmc_ids[] = {
+ { .compatible = "ti,am3352-gpmc" },
+ { }
+};
+
+U_BOOT_DRIVER(omap_gpmc) = {
+ .name = "omap_gpmc",
+ .id = UCLASS_NAND,
+ .of_match = omap_gpmc_ids,
+ .ofdata_to_platdata = omap_gpmc_ofdata_to_platdata,
+ .probe = omap_gpmc_probe,
+ .priv_auto_alloc_size = sizeof(struct nand_chip),
+ .platdata_auto_alloc_size = sizeof(struct omap_gpmc_platdata),
+ .flags = DM_FLAG_ALLOC_PRIV_DMA,
+};
+#endif /* CONFIG_DM_NAND */
--
2.10.1.dirty
More information about the U-Boot
mailing list