[U-Boot] [linux-sunxi] [PATCH v2] sun50i: h5: Add initial Orangepi Prime support

[Maxime Ripard]

On Fri, Jun 02, 2017 at 10:31:48PM +0800, icenowy at aosc.io wrote:
> 在 2017-06-01 23:25，Jagan Teki 写道：
> > From: Jagan Teki <jagan at amarulasolutions.com>
> > 
> > Orangepi Prime is an open-source single-board computer
> > using the Allwinner h5 SOC.
> > 
> > H5 Orangepi Prime has
> > - Quad-core Cortex-A53
> > - 2GB DDR3
> > - Debug TTL UART
> > - 1000M/100M Ethernet RJ45
> > - Three USB 2.0
> > - HDMI
> > - Audio and MIC
> > - Wifi + BT
> > - IR receiver
> > - HDMI
> > - Wifi + BT
> > 
> > Boot from MMC:
> > -------------
> > U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
> > DRAM: 2048 MiB
> > Trying to boot from MMC1
> > NOTICE:  BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
> > NOTICE:  Configuring SPC Controller
> > NOTICE:  BL3-1: v1.0(debug):aa75c8d
> > NOTICE:  BL3-1: Built : 18:28:27, May 24 2017
> > INFO:    BL3-1: Initializing runtime services
> > INFO:    BL3-1: Preparing for EL3 exit to normal world
> > INFO:    BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
> > 
> > U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000)
> > Allwinner Technology
> > 
> > CPU:   Allwinner H5 (SUN50I)
> > Model: OrangePi Prime
> > DRAM:  2 GiB
> > MMC:   SUNXI SD/MMC: 0
> > *** Warning - bad CRC, using default environment
> > 
> > In:    serial
> > Out:   serial
> > Err:   serial
> > Net:   phy interface7
> > eth0: ethernet at 1c30000
> > starting USB...
> > USB0:   USB EHCI 1.00
> > USB1:   USB OHCI 1.0
> > scanning bus 0 for devices... 1 USB Device(s) found
> >        scanning usb for storage devices... 0 Storage Device(s) found
> > Hit any key to stop autoboot:  0
> > 
> > Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
> > ---
> > Changes for v2:
> > - Drop http link from commit message
> > - Drop CONFIG_CONSOLE_MUX
> 
> Why drop this?
> 
> I think now vidconsole is working on H5...

Because it doesn't make any sense to have it in only one or a fraction
of the boards we support.

This is something the user should choose, and opt in.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170602/c3c73614/attachment.sig>