[U-Boot] [PATCHv5 3/3] ARM64: poplar: hi3798cv200: u-boot support for Poplar 96Boards
Jorge Ramirez
jorge.ramirez-ortiz at linaro.org
Wed Jun 7 14:57:33 UTC 2017
just a quick reminder that this is pending
cheers
jorge
On 05/29/2017 04:11 PM, Jorge Ramirez-Ortiz wrote:
> This port adds support for:
> 1) Serial
> 2) eMMC
> 3) USB
>
> It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
> BL33 executable [see board's README]
>
> eMMC has been tested for reading and booting the loader and linux
> kernels as well as saving the u-boot environment.
>
> USB has been tested with ASIX networking adapter and SanDisk 7.4GB
> drive.
>
> PSCI has been tested via the reset call.
> Since PSCI runs in DDR, u-boot carves the necessary memory from
> the kernel memory map.
>
> The firwmare upgrade process has been tested via TFTP and USB FAT
> filesystem containing the fastboot.bin image in one of the partitions.
>
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org>
> ---
> arch/arm/Kconfig | 12 ++
> arch/arm/dts/hi3798cv200-u-boot.dtsi | 29 +++
> arch/arm/include/asm/arch-hi3798cv200/dwmmc.h | 13 ++
> .../arm/include/asm/arch-hi3798cv200/hi3798cv200.h | 50 +++++
> board/hisilicon/poplar/Kconfig | 15 ++
> board/hisilicon/poplar/MAINTAINERS | 6 +
> board/hisilicon/poplar/Makefile | 7 +
> board/hisilicon/poplar/README | 232 +++++++++++++++++++++
> board/hisilicon/poplar/poplar.c | 174 ++++++++++++++++
> configs/poplar_defconfig | 26 +++
> include/configs/poplar.h | 86 ++++++++
> 11 files changed, 650 insertions(+)
> create mode 100644 arch/arm/dts/hi3798cv200-u-boot.dtsi
> create mode 100644 arch/arm/include/asm/arch-hi3798cv200/dwmmc.h
> create mode 100644 arch/arm/include/asm/arch-hi3798cv200/hi3798cv200.h
> create mode 100644 board/hisilicon/poplar/Kconfig
> create mode 100644 board/hisilicon/poplar/MAINTAINERS
> create mode 100644 board/hisilicon/poplar/Makefile
> create mode 100644 board/hisilicon/poplar/README
> create mode 100644 board/hisilicon/poplar/poplar.c
> create mode 100644 configs/poplar_defconfig
> create mode 100644 include/configs/poplar.h
>
> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> index 91f50b0..7e908ca 100644
> --- a/arch/arm/Kconfig
> +++ b/arch/arm/Kconfig
> @@ -811,6 +811,17 @@ config TARGET_HIKEY
> Support for HiKey 96boards platform. It features a HI6220
> SoC, with 8xA53 CPU, mali450 gpu, and 1GB RAM.
>
> +config TARGET_POPLAR
> + bool "Support Poplar 96boards Enterprise Edition Platform"
> + select ARM64
> + select DM
> + select OF_CONTROL
> + select DM_SERIAL
> + select DM_USB
> + help
> + Support for Poplar 96boards EE platform. It features a HI3798cv200
> + SoC, with 4xA53 CPU, MaliT720 GPU, and 1GB RAM.
> +
> config TARGET_LS1012AQDS
> bool "Support ls1012aqds"
> select ARCH_LS1012A
> @@ -1137,6 +1148,7 @@ source "board/grinn/chiliboard/Kconfig"
> source "board/gumstix/pepper/Kconfig"
> source "board/h2200/Kconfig"
> source "board/hisilicon/hikey/Kconfig"
> +source "board/hisilicon/poplar/Kconfig"
> source "board/imx31_phycore/Kconfig"
> source "board/isee/igep003x/Kconfig"
> source "board/olimex/mx23_olinuxino/Kconfig"
> diff --git a/arch/arm/dts/hi3798cv200-u-boot.dtsi b/arch/arm/dts/hi3798cv200-u-boot.dtsi
> new file mode 100644
> index 0000000..2b3713b
> --- /dev/null
> +++ b/arch/arm/dts/hi3798cv200-u-boot.dtsi
> @@ -0,0 +1,29 @@
> +/*
> + * U-Boot addition to:
> + * 1) use platform data for the console
> + * 2) provide support for the generic-ehci USB driver currently not available
> + * in the linux kernel (8/May/2017).
> + *
> + * (C) Copyright 2017 Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +&soc {
> + usb2: ehci at 9890000 {
> + compatible = "generic-ehci";
> + reg = <0x9890000 0x100>;
> + status = "okay";
> + };
> +};
> +
> +&uart0 {
> + status = "disabled";
> +};
> +
> +/{
> + chosen {
> + stdout-path = "";
> + };
> +};
> +
> diff --git a/arch/arm/include/asm/arch-hi3798cv200/dwmmc.h b/arch/arm/include/asm/arch-hi3798cv200/dwmmc.h
> new file mode 100644
> index 0000000..1060d94
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-hi3798cv200/dwmmc.h
> @@ -0,0 +1,13 @@
> +/*
> + * (C) Copyright 2017 Linaro
> + * Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef _HI3798cv200_DWMMC_H_
> +#define _HI3798cv200_DWMMC_H_
> +
> +int hi6220_dwmci_add_port(int index, u32 regbase, int bus_width);
> +
> +#endif /* _HI3798cv200_DWMMC_H_ */
> diff --git a/arch/arm/include/asm/arch-hi3798cv200/hi3798cv200.h b/arch/arm/include/asm/arch-hi3798cv200/hi3798cv200.h
> new file mode 100644
> index 0000000..d30e0b4
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-hi3798cv200/hi3798cv200.h
> @@ -0,0 +1,50 @@
> +/*
> + * (C) Copyright 2017 Linaro
> + * Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __HI3798cv200_H__
> +#define __HI3798cv200_H__
> +
> +#define REG_BASE_PERI_CTRL 0xF8A20000
> +#define REG_BASE_CRG 0xF8A22000
> +
> +/* DEVICES */
> +#define REG_BASE_MCI 0xF9830000
> +#define REG_BASE_UART0 0xF8B00000
> +
> +/* PERI control registers (4KB) */
> + /* USB2 PHY01 configuration register */
> +#define PERI_CTRL_USB0 (REG_BASE_PERI_CTRL + 0x120)
> +
> +/* PERI CRG registers (4KB) */
> + /* USB2 CTRL0 clock and soft reset */
> +#define PERI_CRG46 (REG_BASE_CRG + 0xb8)
> +#define USB2_BUS_CKEN (1<<0)
> +#define USB2_OHCI48M_CKEN (1<<1)
> +#define USB2_OHCI12M_CKEN (1<<2)
> +#define USB2_OTG_UTMI_CKEN (1<<3)
> +#define USB2_HST_PHY_CKEN (1<<4)
> +#define USB2_UTMI0_CKEN (1<<5)
> +#define USB2_BUS_SRST_REQ (1<<12)
> +#define USB2_UTMI0_SRST_REQ (1<<13)
> +#define USB2_HST_PHY_SYST_REQ (1<<16)
> +#define USB2_OTG_PHY_SYST_REQ (1<<17)
> +#define USB2_CLK48_SEL (1<<20)
> +
> + /* USB2 PHY clock and soft reset */
> +#define PERI_CRG47 (REG_BASE_CRG + 0xbc)
> +#define USB2_PHY01_REF_CKEN (1 << 0)
> +#define USB2_PHY2_REF_CKEN (1 << 2)
> +#define USB2_PHY01_SRST_REQ (1 << 4)
> +#define USB2_PHY2_SRST_REQ (1 << 6)
> +#define USB2_PHY01_SRST_TREQ0 (1 << 8)
> +#define USB2_PHY01_SRST_TREQ1 (1 << 9)
> +#define USB2_PHY2_SRST_TREQ (1 << 10)
> +#define USB2_PHY01_REFCLK_SEL (1 << 12)
> +#define USB2_PHY2_REFCLK_SEL (1 << 14)
> +
> +
> +#endif
> diff --git a/board/hisilicon/poplar/Kconfig b/board/hisilicon/poplar/Kconfig
> new file mode 100644
> index 0000000..3397295
> --- /dev/null
> +++ b/board/hisilicon/poplar/Kconfig
> @@ -0,0 +1,15 @@
> +if TARGET_POPLAR
> +
> +config SYS_BOARD
> + default "poplar"
> +
> +config SYS_VENDOR
> + default "hisilicon"
> +
> +config SYS_SOC
> + default "hi3798cv200"
> +
> +config SYS_CONFIG_NAME
> + default "poplar"
> +
> +endif
> diff --git a/board/hisilicon/poplar/MAINTAINERS b/board/hisilicon/poplar/MAINTAINERS
> new file mode 100644
> index 0000000..0cc01c8
> --- /dev/null
> +++ b/board/hisilicon/poplar/MAINTAINERS
> @@ -0,0 +1,6 @@
> +Poplar BOARD
> +M: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org>
> +S: Maintained
> +F: board/hisilicon/poplar
> +F: include/configs/poplar.h
> +F: configs/poplar_defconfig
> diff --git a/board/hisilicon/poplar/Makefile b/board/hisilicon/poplar/Makefile
> new file mode 100644
> index 0000000..101545d
> --- /dev/null
> +++ b/board/hisilicon/poplar/Makefile
> @@ -0,0 +1,7 @@
> +#
> +# (C) Copyright 2017 Linaro
> +# Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org>
> +#
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +obj-y := poplar.o
> diff --git a/board/hisilicon/poplar/README b/board/hisilicon/poplar/README
> new file mode 100644
> index 0000000..97782e7
> --- /dev/null
> +++ b/board/hisilicon/poplar/README
> @@ -0,0 +1,232 @@
> +================================================================================
> + Board Information
> +================================================================================
> +
> +Developed by HiSilicon, the board features the Hi3798C V200 with an
> +integrated quad-core 64-bit ARM Cortex A53 processor and high
> +performance Mali T720 GPU, making it capable of running any commercial
> +set-top solution based on Linux or Android. Its high performance
> +specification also supports a premium user experience with up to H.265
> +HEVC decoding of 4K video at 60 frames per second.
> +
> +SOC Hisilicon Hi3798CV200
> +CPU Quad-core ARM Cortex-A53 64 bit
> +DRAM DDR3/3L/4 SDRAM interface, maximum 32-bit data width 2 GB
> +USB Two USB 2.0 ports One USB 3.0 ports
> +CONSOLE USB-micro port for console support
> +ETHERNET 1 GBe Ethernet
> +PCIE One PCIe 2.0 interfaces
> +JTAG 8-Pin JTAG
> +EXPANSION INTERFACE Linaro 96Boards Low Speed Expansion slot
> +DIMENSION Standard 160×120 mm 96Boards Enterprice Edition form factor
> +WIFI 802.11AC 2*2 with Bluetooth
> +CONNECTORS One connector for Smart Card One connector for TSI
> +
> +
> +================================================================================
> + BUILD INSTRUCTIONS
> +================================================================================
> +
> +Compile from source:
> +====================
> +
> +Get all the sources
> +
> + > mkdir -p ~/poplar/src ~/poplar/bin
> + > cd ~/poplar/src
> + > git clone https://github.com/Linaro/poplar-l-loader.git l-loader
> + > git clone https://github.com/Linaro/poplar-arm-trusted-firmware.git atf
> + > git clone https://github.com/Linaro/poplar-u-boot.git u-boot
> +
> +
> +Compile U-Boot:
> +===============
> +
> + Prerequisite:
> + # sudo apt-get install device-tree-compiler
> +
> + > cd ~/poplar/src/u-boot
> + > make CROSS_COMPILE=aarch64-linux-gnu- poplar_defconfig
> + > make CROSS_COMPILE=aarch64-linux-gnu-
> + > cp u-boot.bin ~/poplar/bin
> +
> +Compile ARM Trusted Firmware (ATF):
> +===================================
> +
> + > cd ~/poplar/src/atf
> + > make CROSS_COMPILE=aarch64-linux-gnu- all fip \
> + SPD=none BL33=~/poplar/bin/u-boot.bin DEBUG=1 PLAT=poplar
> +
> +Copy resulting binaries
> + > cp build/hi3798cv200/debug/bl1.bin ~/poplar/src/l-loader/atf/
> + > cp build/hi3798cv200/debug/fip.bin ~/poplar/src/l-loader/atf/
> +
> +Compile l-loader:
> +=================
> +
> + > cd ~/poplar/src/l-loader
> + > make clean
> + > make CROSS_COMPILE=arm-linux-gnueabi-
> +
> + Due to BootROM requiremets, rename l-loader.bin to fastboot.bin:
> + > cp l-loader.bin ~/poplar/bin/fastboot.bin
> +
> +
> +================================================================================
> + FLASH INSTRUCTIONS
> +================================================================================
> +
> +Two methods:
> +
> +Using USB debrick support:
> + Copy fastboot.bin to a FAT partition on the USB drive and reboot the
> + poplar board while pressing S3(usb_boot).
> +
> + The system will execute the new u-boot and boot into a shell which you
> + can then use to write to eMMC.
> +
> +Using U-BOOT from shell:
> + 1) using AXIS usb ethernet dongle and tftp
> + 2) using FAT formated USB drive
> +
> +
> +1. TFTP (USB ethernet dongle)
> +=============================
> +
> +Plug a USB AXIS ethernet dongle on any of the USB2 ports on the Poplar board.
> +Copy fastboot.bin to your tftp server.
> +In u-boot make sure your network is properly setup.
> +
> +Then
> +
> +=> tftp 0x30000000 fastboot.bin
> +starting USB...
> +USB0: USB EHCI 1.00
> +scanning bus 0 for devices... 1 USB Device(s) found
> +USB1: USB EHCI 1.00
> +scanning bus 1 for devices... 3 USB Device(s) found
> + scanning usb for storage devices... 0 Storage Device(s) found
> + scanning usb for ethernet devices... 1 Ethernet Device(s) found
> +Waiting for Ethernet connection... done.
> +Using asx0 device
> +TFTP from server 192.168.1.4; our IP address is 192.168.1.10
> +Filename 'poplar/fastboot.bin'.
> +Load address: 0x30000000
> +Loading: #################################################################
> + #################################################################
> + ###############################################################
> + 2 MiB/s
> +done
> +Bytes transferred = 983040 (f0000 hex)
> +
> +=> mmc write 0x30000000 0 0x780
> +
> +MMC write: dev # 0, block # 0, count 1920 ... 1920 blocks written: OK
> +=> reset
> +
> +
> +2. USING USB FAT DRIVE
> +=======================
> +
> +Copy fastboot.bin to any partition on a FAT32 formated usb flash drive.
> +Enter the uboot prompt
> +
> +=> fatls usb 0:2
> + 983040 fastboot.bin
> +
> +1 file(s), 0 dir(s)
> +
> +=> fatload usb 0:2 0x30000000 fastboot.bin
> +reading fastboot.bin
> +983040 bytes read in 44 ms (21.3 MiB/s)
> +
> +=> mmc write 0x30000000 0 0x780
> +
> +MMC write: dev # 0, block # 0, count 1920 ... 1920 blocks written: OK
> +
> +
> +================================================================================
> + BOOT TRACE
> +================================================================================
> +
> +Bootrom start
> +Boot Media: eMMC
> +Decrypt auxiliary code ...OK
> +
> +lsadc voltage min: 000000FE, max: 000000FF, aver: 000000FE, index: 00000000
> +
> +Entry boot auxiliary code
> +
> +Auxiliary code - v1.00
> +DDR code - V1.1.2 20160205
> +Build: Mar 24 2016 - 17:09:44
> +Reg Version: v134
> +Reg Time: 2016/03/18 09:44:55
> +Reg Name: hi3798cv2dmb_hi3798cv200_ddr3_2gbyte_8bitx4_4layers.reg
> +
> +Boot auxiliary code success
> +Bootrom success
> +
> +LOADER: Switched to aarch64 mode
> +LOADER: Entering ARM TRUSTED FIRMWARE
> +LOADER: CPU0 executes at 0x000ce000
> +
> +INFO: BL1: 0xe1000 - 0xe7000 [size = 24576]
> +NOTICE: Booting Trusted Firmware
> +NOTICE: BL1: v1.3(debug):v1.3-372-g1ba9c60
> +NOTICE: BL1: Built : 17:51:33, Apr 30 2017
> +INFO: BL1: RAM 0xe1000 - 0xe7000
> +INFO: BL1: Loading BL2
> +INFO: Loading image id=1 at address 0xe9000
> +INFO: Image id=1 loaded at address 0xe9000, size = 0x5008
> +NOTICE: BL1: Booting BL2
> +INFO: Entry point address = 0xe9000
> +INFO: SPSR = 0x3c5
> +NOTICE: BL2: v1.3(debug):v1.3-372-g1ba9c60
> +NOTICE: BL2: Built : 17:51:33, Apr 30 2017
> +INFO: BL2: Loading BL31
> +INFO: Loading image id=3 at address 0x129000
> +INFO: Image id=3 loaded at address 0x129000, size = 0x8038
> +INFO: BL2: Loading BL33
> +INFO: Loading image id=5 at address 0x37000000
> +INFO: Image id=5 loaded at address 0x37000000, size = 0x58f17
> +NOTICE: BL1: Booting BL31
> +INFO: Entry point address = 0x129000
> +INFO: SPSR = 0x3cd
> +INFO: Boot bl33 from 0x37000000 for 364311 Bytes
> +NOTICE: BL31: v1.3(debug):v1.3-372-g1ba9c60
> +NOTICE: BL31: Built : 17:51:33, Apr 30 2017
> +INFO: BL31: Initializing runtime services
> +INFO: BL31: Preparing for EL3 exit to normal world
> +INFO: Entry point address = 0x37000000
> +INFO: SPSR = 0x3c9
> +
> +
> +U-Boot 2017.05-rc2-00130-gd2255b0 (Apr 30 2017 - 17:51:28 +0200)poplar
> +
> +Model: HiSilicon Poplar Development Board
> +BOARD: Hisilicon HI3798cv200 Poplar
> +DRAM: 1 GiB
> +MMC: Hisilicon DWMMC: 0
> +In: serial at f8b00000
> +Out: serial at f8b00000
> +Err: serial at f8b00000
> +Net: Net Initialization Skipped
> +No ethernet found.
> +
> +Hit any key to stop autoboot: 0
> +starting USB...
> +USB0: USB EHCI 1.00
> +scanning bus 0 for devices... 1 USB Device(s) found
> +USB1: USB EHCI 1.00
> +scanning bus 1 for devices... 4 USB Device(s) found
> + scanning usb for storage devices... 1 Storage Device(s) found
> + scanning usb for ethernet devices... 1 Ethernet Device(s) found
> +
> +USB device 0:
> + Device 0: Vendor: SanDisk Rev: 1.00 Prod: Cruzer Blade
> + Type: Removable Hard Disk
> + Capacity: 7632.0 MB = 7.4 GB (15630336 x 512)
> +... is now current device
> +Scanning usb 0:1...
> +=>
> diff --git a/board/hisilicon/poplar/poplar.c b/board/hisilicon/poplar/poplar.c
> new file mode 100644
> index 0000000..b4ac371
> --- /dev/null
> +++ b/board/hisilicon/poplar/poplar.c
> @@ -0,0 +1,174 @@
> +/*
> + * (C) Copyright 2017 Linaro
> + * Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <dm/platform_data/serial_pl01x.h>
> +#include <asm/arch/hi3798cv200.h>
> +#include <asm/arch/dwmmc.h>
> +#include <asm/armv8/mmu.h>
> +#include <asm/io.h>
> +#include <dm.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +static struct mm_region poplar_mem_map[] = {
> + {
> + .virt = 0x0UL,
> + .phys = 0x0UL,
> + .size = 0x80000000UL,
> + .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
> + PTE_BLOCK_INNER_SHARE
> + }, {
> + .virt = 0x80000000UL,
> + .phys = 0x80000000UL,
> + .size = 0x80000000UL,
> + .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
> + PTE_BLOCK_NON_SHARE |
> + PTE_BLOCK_PXN | PTE_BLOCK_UXN
> + }, {
> + 0,
> + }
> +};
> +
> +struct mm_region *mem_map = poplar_mem_map;
> +
> +static const struct pl01x_serial_platdata serial_platdata = {
> + .base = REG_BASE_UART0,
> + .type = TYPE_PL010,
> + .clock = 75000000,
> +};
> +
> +U_BOOT_DEVICE(poplar_serial) = {
> + .name = "serial_pl01x",
> + .platdata = &serial_platdata,
> +};
> +
> +int checkboard(void)
> +{
> + puts("BOARD: Hisilicon HI3798cv200 Poplar\n");
> +
> + return 0;
> +}
> +
> +void reset_cpu(ulong addr)
> +{
> + psci_system_reset();
> +}
> +
> +int dram_init(void)
> +{
> + gd->ram_size = get_ram_size(NULL, 0x80000000);
> +
> + return 0;
> +}
> +
> +int dram_init_banksize(void)
> +{
> + const struct {
> + phys_addr_t start;
> + phys_addr_t end;
> + char *name;
> + } reserved = {
> + /* ATF PSCI runs in DDR (no SRAM available for it) */
> + .name = "atf-bl31",
> + .start = 0x129000,
> + .end = 0x129000 + 0x8020,
> + };
> +
> + gd->bd->bi_dram[0].start = 0x0;
> + gd->bd->bi_dram[0].size = reserved.start;
> +
> + gd->bd->bi_dram[1].start = reserved.end;
> + gd->bd->bi_dram[1].size = gd->ram_size - reserved.end;
> +
> + return 0;
> +}
> +
> +static void usb2_phy_config(void)
> +{
> + const u32 config[] = {
> + /* close EOP pre-emphasis. open data pre-emphasis */
> + 0xa1001c,
> + /* Rcomp = 150mW, increase DC level */
> + 0xa00607,
> + /* keep Rcomp working */
> + 0xa10700,
> + /* Icomp = 212mW, increase current drive */
> + 0xa00aab,
> + /* EMI fix: rx_active not stay 1 when error packets received */
> + 0xa11140,
> + /* Comp mode select */
> + 0xa11041,
> + /* adjust eye diagram */
> + 0xa0098c,
> + /* adjust eye diagram */
> + 0xa10a0a,
> + };
> + int i;
> +
> + for (i = 0; i < ARRAY_SIZE(config); i++) {
> + writel(config[i], PERI_CTRL_USB0);
> + clrsetbits_le32(PERI_CTRL_USB0, BIT(21), BIT(20) | BIT(22));
> + udelay(20);
> + }
> +}
> +
> +static void usb2_phy_init(void)
> +{
> + /* reset usb2 controller bus/utmi/roothub */
> + setbits_le32(PERI_CRG46, USB2_BUS_SRST_REQ | USB2_UTMI0_SRST_REQ |
> + USB2_HST_PHY_SYST_REQ | USB2_OTG_PHY_SYST_REQ);
> + udelay(200);
> +
> + /* reset usb2 phy por/utmi */
> + setbits_le32(PERI_CRG47, USB2_PHY01_SRST_REQ | USB2_PHY01_SRST_TREQ1);
> + udelay(200);
> +
> + /* open usb2 ref clk */
> + setbits_le32(PERI_CRG47, USB2_PHY01_REF_CKEN);
> + udelay(300);
> +
> + /* cancel usb2 power on reset */
> + clrbits_le32(PERI_CRG47, USB2_PHY01_SRST_REQ);
> + udelay(500);
> +
> + usb2_phy_config();
> +
> + /* cancel usb2 port reset, wait comp circuit stable */
> + clrbits_le32(PERI_CRG47, USB2_PHY01_SRST_TREQ1);
> + mdelay(10);
> +
> + /* open usb2 controller clk */
> + setbits_le32(PERI_CRG46, USB2_BUS_CKEN | USB2_OHCI48M_CKEN |
> + USB2_OHCI12M_CKEN | USB2_OTG_UTMI_CKEN |
> + USB2_HST_PHY_CKEN | USB2_UTMI0_CKEN);
> + udelay(200);
> +
> + /* cancel usb2 control reset */
> + clrbits_le32(PERI_CRG46, USB2_BUS_SRST_REQ | USB2_UTMI0_SRST_REQ |
> + USB2_HST_PHY_SYST_REQ | USB2_OTG_PHY_SYST_REQ);
> + udelay(200);
> +}
> +
> +int board_mmc_init(bd_t *bis)
> +{
> + int ret;
> +
> + ret = hi6220_dwmci_add_port(0, REG_BASE_MCI, 8);
> + if (ret)
> + printf("mmc init error (%d)\n", ret);
> +
> + return ret;
> +}
> +
> +int board_init(void)
> +{
> + usb2_phy_init();
> +
> + return 0;
> +}
> +
> diff --git a/configs/poplar_defconfig b/configs/poplar_defconfig
> new file mode 100644
> index 0000000..8f9f40f
> --- /dev/null
> +++ b/configs/poplar_defconfig
> @@ -0,0 +1,26 @@
> +CONFIG_ARM=y
> +CONFIG_TARGET_POPLAR=y
> +CONFIG_IDENT_STRING="poplar"
> +CONFIG_DEFAULT_DEVICE_TREE="hi3798cv200-poplar"
> +CONFIG_SYS_PROMPT="poplar# "
> +CONFIG_DISTRO_DEFAULTS=y
> +CONFIG_DISPLAY_CPUINFO=n
> +CONFIG_DISPLAY_BOARDINFO=y
> +CONFIG_ISO_PARTITION=n
> +CONFIG_MMC_DW=y
> +CONFIG_MMC_DW_K3=y
> +CONFIG_PL011_SERIAL=y
> +CONFIG_PSCI_RESET=y
> +CONFIG_USB=y
> +CONFIG_USB_EHCI=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_GENERIC=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_NET=y
> +# CONFIG_CMD_IMLS is not set
> +# CONFIG_DM_GPIO is not set
> +CONFIG_LIB_RAND=y
> +CONFIG_CMD_UNZIP=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_USB=y
> +
> diff --git a/include/configs/poplar.h b/include/configs/poplar.h
> new file mode 100644
> index 0000000..55e05d6
> --- /dev/null
> +++ b/include/configs/poplar.h
> @@ -0,0 +1,86 @@
> +/*
> + * (C) Copyright 2017 Linaro
> + *
> + * Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org>
> + *
> + * Configuration for Poplar 96boards CE. Parts were derived from other ARM
> + * configurations.
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef _POPLAR_H_
> +#define _POPLAR_H_
> +
> +#include <linux/sizes.h>
> +
> +/* DRAM banks */
> +#define CONFIG_NR_DRAM_BANKS 2
> +
> +/* SYS */
> +#define CONFIG_SYS_BOOTM_LEN 0x1400000
> +#define CONFIG_SYS_INIT_SP_ADDR 0x200000
> +#define CONFIG_SYS_LOAD_ADDR 0x800000
> +#define CONFIG_SYS_MALLOC_LEN SZ_32M
> +
> +/* ATF bl33.bin load address (must match) */
> +#define CONFIG_SYS_TEXT_BASE 0x37000000
> +
> +/* PL010/PL011 */
> +#define CONFIG_PL01X_SERIAL
> +
> +/* USB configuration */
> +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
> +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
> +#define CONFIG_SYS_USB_EVENT_POLL
> +#define CONFIG_USB_HOST_ETHER
> +#define CONFIG_USB_ETHER_ASIX
> +
> +/* SD/MMC */
> +#define CONFIG_BOUNCE_BUFFER
> +
> +/*****************************************************************************
> + * Initial environment variables
> + *****************************************************************************/
> +
> +#define BOOT_TARGET_DEVICES(func) \
> + func(USB, usb, 0) \
> + func(MMC, mmc, 0) \
> + func(DHCP, dhcp, na)
> +#ifndef CONFIG_SPL_BUILD
> +#include <config_distro_defaults.h>
> +#include <config_distro_bootcmd.h>
> +#endif
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "loader_mmc_blknum=0x0\0" \
> + "loader_mmc_nblks=0x780\0" \
> + "env_mmc_blknum=0x780\0" \
> + "env_mmc_nblks=0x80\0" \
> + "kernel_addr_r=0x30000000\0" \
> + "pxefile_addr_r=0x32000000\0" \
> + "scriptaddr=0x32000000\0" \
> + "fdt_addr_r=0x32200000\0" \
> + "fdtfile=hisilicon/hi3798cv200-poplar.dtb\0" \
> + "ramdisk_addr_r=0x32400000\0" \
> + BOOTENV
> +
> +
> +/* Command line configuration */
> +#define CONFIG_ENV_IS_IN_MMC 1
> +#define CONFIG_SYS_MMC_ENV_DEV 0
> +#define CONFIG_ENV_OFFSET (0x780 * 512) /* env_mmc_blknum */
> +#define CONFIG_ENV_SIZE 0x10000 /* env_mmc_nblks bytes */
> +#define CONFIG_FAT_WRITE
> +#define CONFIG_ENV_VARS_UBOOT_CONFIG
> +
> +/* Monitor Command Prompt */
> +#define CONFIG_CMDLINE_EDITING
> +#define CONFIG_SYS_LONGHELP
> +#define CONFIG_SYS_CBSIZE 512
> +#define CONFIG_SYS_MAXARGS 64
> +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
> + sizeof(CONFIG_SYS_PROMPT) + 16)
> +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
> +
> +#endif /* _POPLAR_H_ */
More information about the U-Boot
mailing list