[U-Boot] [PATCH v4 3/4] rockchip: Add basic support for phyCORE-RK3288 SoM based carrier board
Wadim Egorov
w.egorov at phytec.de
Mon Jun 19 10:36:40 UTC 2017
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Signed-off-by: Wadim Egorov <w.egorov at phytec.de>
Reviewed-by: Simon Glass <sjg at chromium.org>
---
Changes in v4:
- Use of_machine_is_compatible()
- Wrap phycore_init()/of_machine_is_compatible() with CONFIG_SPL_OF_PLATDATA
and CONFIG_SPL_POWER_SUPPORT. Needed because of_machine_is_compatible() and
rk818_spl_configure_*() is not available with all rk3288 board configs.
- Added Reviewed-by: Simon Glass <sjg at chromium.org>
arch/arm/dts/Makefile | 1 +
arch/arm/dts/rk3288-phycore-rdk.dts | 294 ++++++++++++++++
arch/arm/dts/rk3288-phycore-som.dtsi | 506 +++++++++++++++++++++++++++
arch/arm/mach-rockchip/rk3288-board-spl.c | 40 +++
arch/arm/mach-rockchip/rk3288/Kconfig | 10 +
board/phytec/phycore_rk3288/Kconfig | 15 +
board/phytec/phycore_rk3288/MAINTAINERS | 6 +
board/phytec/phycore_rk3288/Makefile | 8 +
board/phytec/phycore_rk3288/phycore-rk3288.c | 8 +
configs/phycore-rk3288_defconfig | 70 ++++
include/configs/phycore_rk3288.h | 23 ++
11 files changed, 981 insertions(+)
create mode 100644 arch/arm/dts/rk3288-phycore-rdk.dts
create mode 100644 arch/arm/dts/rk3288-phycore-som.dtsi
create mode 100644 board/phytec/phycore_rk3288/Kconfig
create mode 100644 board/phytec/phycore_rk3288/MAINTAINERS
create mode 100644 board/phytec/phycore_rk3288/Makefile
create mode 100644 board/phytec/phycore_rk3288/phycore-rk3288.c
create mode 100644 configs/phycore-rk3288_defconfig
create mode 100644 include/configs/phycore_rk3288.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 8b8f5e9..84f63e1 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -34,6 +34,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3288-fennec.dtb \
rk3288-firefly.dtb \
rk3288-miqi.dtb \
+ rk3288-phycore-rdk.dtb \
rk3288-popmetal.dtb \
rk3288-rock2-square.dtb \
rk3288-tinker.dtb \
diff --git a/arch/arm/dts/rk3288-phycore-rdk.dts b/arch/arm/dts/rk3288-phycore-rdk.dts
new file mode 100644
index 0000000..f2bb7b5
--- /dev/null
+++ b/arch/arm/dts/rk3288-phycore-rdk.dts
@@ -0,0 +1,294 @@
+/*
+ * Device tree file for Phytec PCM-947 carrier board
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov at phytec.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "rk3288-phycore-som.dtsi"
+
+/ {
+ model = "Phytec RK3288 PCM-947";
+ compatible = "phytec,rk3288-pcm-947", "phytec,rk3288-phycore-som", "rockchip,rk3288";
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ config {
+ u-boot,dm-pre-reloc;
+ u-boot,boot0 = &emmc;
+ };
+
+ user_buttons: user-buttons {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_button_pins>;
+
+ button at 0 {
+ label = "home";
+ linux,code = <KEY_HOME>;
+ gpios = <&gpio8 0 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+ };
+
+ button at 1 {
+ label = "menu";
+ linux,code = <KEY_MENU>;
+ gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+ };
+ };
+
+ vcc_host0_5v: usb-host0-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host0_vbus_drv>;
+ regulator-name = "vcc_host0_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&vdd_in_otg_out>;
+ };
+
+ vcc_host1_5v: usb-host1-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host1_vbus_drv>;
+ regulator-name = "vcc_host1_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&vdd_in_otg_out>;
+ };
+
+ vcc_otg_5v: usb-otg-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio2 12 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_vbus_drv>;
+ regulator-name = "vcc_otg_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&vdd_in_otg_out>;
+ };
+};
+
+&dmc {
+ rockchip,num-channels = <2>;
+ rockchip,pctl-timing = <0x29a 0xc8 0x1f8 0x42 0x4e 0x4 0xea 0xa
+ 0x5 0x0 0xa 0x7 0x19 0x24 0xa 0x7
+ 0x5 0xa 0x5 0x200 0x5 0x10 0x40 0x0
+ 0x1 0x7 0x7 0x4 0xc 0x43 0x100 0x0
+ 0x5 0x0>;
+ rockchip,phy-timing = <0x48f9aab4 0xea0910 0x1002c200
+ 0xa60 0x40 0x10 0x0>;
+ rockchip,sdram-channel = /bits/ 8 <0x1 0xa 0x3 0x2 0x1 0x0 0xe 0xe>;
+ rockchip,sdram-params = <0x30B25564 0x627 3 666000000 3 5 1>;
+};
+
+&gmac {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ touchscreen at 44 {
+ compatible = "st,stmpe811";
+ reg = <0x44>;
+ };
+
+ adc at 64 {
+ compatible = "maxim,max1037";
+ reg = <0x64>;
+ };
+
+ i2c_rtc: rtc at 68 {
+ compatible = "rv4162";
+ reg = <0x68>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_rtc_int>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <10 0>;
+ };
+};
+
+&i2c3 {
+ status = "okay";
+
+ i2c_eeprom_cb: eeprom at 51 {
+ compatible = "atmel,24c32";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&i2c4 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&pinctrl {
+ u-boot,dm-pre-reloc;
+
+ pcfg_pull_up_drv_12ma: pcfg-pull-up-drv-12ma {
+ bias-pull-up;
+ drive-strength = <12>;
+ };
+
+ buttons {
+ user_button_pins: user-button-pins {
+ /* button 1 */
+ rockchip,pins = <8 3 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* button 2 */
+ <8 0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ rv4162 {
+ i2c_rtc_int: i2c-rtc-int {
+ rockchip,pins = <5 10 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sdmmc {
+ /*
+ * Default drive strength isn't enough to achieve even
+ * high-speed mode on pcm-947 board so bump up to 12 mA.
+ */
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+ <6 17 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+ <6 18 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+ <6 19 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+ };
+
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_12ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+ };
+
+ sdmmc_pwr: sdmmc-pwr {
+ rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ touchscreen {
+ ts_irq_pin: ts-irq-pin {
+ rockchip,pins = <5 15 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb_host {
+ host0_vbus_drv: host0-vbus-drv {
+ rockchip,pins = <2 13 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ host1_vbus_drv: host1-vbus-drv {
+ rockchip,pins = <2 0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb_otg {
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins = <2 12 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&sdmmc {
+ u-boot,dm-pre-reloc;
+
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ disable-wp;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+ vmmc-supply = <&vdd_io_sd>;
+ vqmmc-supply = <&vdd_io_sd>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ status = "okay";
+};
+
+&uart2 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host1 {
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+};
diff --git a/arch/arm/dts/rk3288-phycore-som.dtsi b/arch/arm/dts/rk3288-phycore-som.dtsi
new file mode 100644
index 0000000..fd463f4
--- /dev/null
+++ b/arch/arm/dts/rk3288-phycore-som.dtsi
@@ -0,0 +1,506 @@
+/*
+ * Device tree file for Phytec phyCORE-RK3288 SoM
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov at phytec.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/net/ti-dp83867.h>
+#include "rk3288.dtsi"
+
+/ {
+ model = "Phytec RK3288 phyCORE";
+ compatible = "phytec,rk3288-phycore-som", "rockchip,rk3288";
+
+ /*
+ * Set the minimum memory size here and
+ * let the bootloader set the real size.
+ */
+ memory {
+ device_type = "memory";
+ reg = <0 0x8000000>;
+ };
+
+ aliases {
+ rtc0 = &i2c_rtc;
+ rtc1 = &rk818;
+ };
+
+ ext_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ };
+
+ io_domains: io_domains {
+ compatible = "rockchip,rk3288-io-voltage-domain";
+
+ status = "okay";
+ sdcard-supply = <&vdd_io_sd>;
+ flash0-supply = <&vdd_emmc_io>;
+ flash1-supply = <&vdd_misc_1v8>;
+ gpio1830-supply = <&vdd_3v3_io>;
+ gpio30-supply = <&vdd_3v3_io>;
+ bb-supply = <&vdd_3v3_io>;
+ dvp-supply = <&vdd_3v3_io>;
+ lcdc-supply = <&vdd_3v3_io>;
+ wifi-supply = <&vdd_3v3_io>;
+ audio-supply = <&vdd_3v3_io>;
+ };
+
+ leds: user-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_led>;
+
+ user {
+ label = "green_led";
+ gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "keep";
+ };
+ };
+
+ vdd_emmc_io: vdd-emmc-io {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_emmc_io";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vdd_3v3_io>;
+ };
+
+ vdd_in_otg_out: vdd-in-otg-out {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_in_otg_out";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vdd_misc_1v8: vdd-misc-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_misc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+};
+
+&cpu0 {
+ cpu0-supply = <&vdd_cpu>;
+ operating-points = <
+ /* KHz uV */
+ 1800000 1400000
+ 1608000 1350000
+ 1512000 1300000
+ 1416000 1200000
+ 1200000 1100000
+ 1008000 1050000
+ 816000 1000000
+ 696000 950000
+ 600000 900000
+ 408000 900000
+ 312000 900000
+ 216000 900000
+ 126000 900000
+ >;
+};
+
+&emmc {
+ status = "okay";
+ u-boot,dm-pre-reloc;
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ disable-wp;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+ vmmc-supply = <&vdd_3v3_io>;
+ vqmmc-supply = <&vdd_emmc_io>;
+};
+
+&gmac {
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ clock_in_out = "input";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins &phy_rst &phy_int>;
+ phy-handle = <&phy0>;
+ phy-supply = <&vdd_eth_2v5>;
+ phy-mode = "rgmii-id";
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 1000000>;
+ snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+ tx_delay = <0x0>;
+ rx_delay = <0x0>;
+
+ mdio0 {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ enet-phy-lane-no-swap;
+ };
+ };
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c5>;
+};
+
+&i2c0 {
+ status = "okay";
+ u-boot,dm-pre-reloc;
+
+ clock-frequency = <400000>;
+
+ rk818: pmic at 1c {
+ status = "okay";
+ compatible = "rockchip,rk818";
+ reg = <0x1c>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>;
+ rockchip,system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+ u-boot,dm-pre-reloc;
+
+ vcc1-supply = <&vdd_sys>;
+ vcc2-supply = <&vdd_sys>;
+ vcc3-supply = <&vdd_sys>;
+ vcc4-supply = <&vdd_sys>;
+ boost-supply = <&vdd_in_otg_out>;
+ vcc6-supply = <&vdd_sys>;
+ vcc7-supply = <&vdd_misc_1v8>;
+ vcc8-supply = <&vdd_misc_1v8>;
+ vcc9-supply = <&vdd_3v3_io>;
+ vddio-supply = <&vdd_3v3_io>;
+
+ regulators {
+ u-boot,dm-pre-reloc;
+ vdd_log: DCDC_REG1 {
+ regulator-name = "vdd_log";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_3v3_io: DCDC_REG4 {
+ regulator-name = "vdd_3v3_io";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vdd_sys: DCDC_BOOST {
+ regulator-name = "vdd_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <5000000>;
+ };
+ };
+
+ /* vcc9 */
+ vdd_sd: SWITCH_REG {
+ regulator-name = "vdd_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* vcc6 */
+ vdd_eth_2v5: LDO_REG2 {
+ regulator-name = "vdd_eth_2v5";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2500000>;
+ };
+ };
+
+ /* vcc7 */
+ vdd_1v0: LDO_REG3 {
+ regulator-name = "vdd_1v0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ /* vcc8 */
+ vdd_1v8_lcd_ldo: LDO_REG4 {
+ regulator-name = "vdd_1v8_lcd_ldo";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ /* vcc8 */
+ vdd_1v0_lcd: LDO_REG6 {
+ regulator-name = "vdd_1v0_lcd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ /* vcc7 */
+ vdd_1v8_ldo: LDO_REG7 {
+ regulator-name = "vdd_1v8_ldo";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ /* vcc9 */
+ vdd_io_sd: LDO_REG9 {
+ regulator-name = "vdd_io_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+ };
+ };
+
+ /* M24C32-D */
+ i2c_eeprom: eeprom at 50 {
+ compatible = "atmel,24c32";
+ reg = <0x50>;
+ pagesize = <32>;
+ };
+
+ vdd_cpu: regulator at 60 {
+ compatible = "fcs,fan53555";
+ reg = <0x60>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-enable-ramp-delay = <300>;
+ regulator-name = "vdd_cpu";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1430000>;
+ regulator-ramp-delay = <8000>;
+ vin-supply = <&vdd_sys>;
+ };
+};
+
+&pinctrl {
+ pcfg_output_high: pcfg-output-high {
+ output-high;
+ };
+
+ emmc {
+ /*
+ * We run eMMC at max speed; bump up drive strength.
+ * We also have external pulls, so disable the internal ones.
+ */
+ emmc_clk: emmc-clk {
+ rockchip,pins = <3 18 RK_FUNC_2 &pcfg_pull_none_12ma>;
+ };
+
+ emmc_cmd: emmc-cmd {
+ rockchip,pins = <3 16 RK_FUNC_2 &pcfg_pull_none_12ma>;
+ };
+
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins = <3 0 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 1 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 2 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 3 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 4 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 5 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 6 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 7 RK_FUNC_2 &pcfg_pull_none_12ma>;
+ };
+ };
+
+ gmac {
+ phy_int: phy-int {
+ rockchip,pins = <4 2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ phy_rst: phy-rst {
+ rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>;
+ };
+ };
+
+ leds {
+ user_led: user-led {
+ rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_output_high>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic-int {
+ rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ /* Pin for switching state between sleep and non-sleep state */
+ pmic_sleep: pmic-sleep {
+ rockchip,pins = <RK_GPIO0 0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vdd_1v8_ldo>;
+};
+
+&spi2 {
+ status = "okay";
+
+ serial_flash: flash at 0 {
+ compatible = "micron,n25q128a13", "jedec,spi-nor";
+ reg = <0x0>;
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "okay";
+ };
+};
+
+&tsadc {
+ status = "okay";
+ rockchip,hw-tshut-mode = <0>;
+ rockchip,hw-tshut-polarity = <0>;
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
diff --git a/arch/arm/mach-rockchip/rk3288-board-spl.c b/arch/arm/mach-rockchip/rk3288-board-spl.c
index 8ca6b1e..5668fd2 100644
--- a/arch/arm/mach-rockchip/rk3288-board-spl.c
+++ b/arch/arm/mach-rockchip/rk3288-board-spl.c
@@ -8,6 +8,7 @@
#include <debug_uart.h>
#include <dm.h>
#include <fdtdec.h>
+#include <i2c.h>
#include <led.h>
#include <malloc.h>
#include <ram.h>
@@ -25,6 +26,7 @@
#include <dm/test.h>
#include <dm/util.h>
#include <power/regulator.h>
+#include <power/rk8xx_pmic.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -157,6 +159,32 @@ static int configure_emmc(struct udevice *pinctrl)
}
#endif
+#if !defined(CONFIG_SPL_OF_PLATDATA)
+static int phycore_init(void)
+{
+ struct udevice *pmic;
+ int ret;
+
+ ret = uclass_first_device_err(UCLASS_PMIC, &pmic);
+ if (ret)
+ return ret;
+
+#if defined(CONFIG_SPL_POWER_SUPPORT)
+ /* Increase USB input current to 2A */
+ ret = rk818_spl_configure_usb_input_current(pmic, 2000);
+ if (ret)
+ return ret;
+
+ /* Close charger when USB lower then 3.26V */
+ ret = rk818_spl_configure_usb_chrg_shutdown(pmic, 3260000);
+ if (ret)
+ return ret;
+#endif
+
+ return 0;
+}
+#endif
+
void board_init_f(ulong dummy)
{
struct udevice *pinctrl;
@@ -203,6 +231,18 @@ void board_init_f(ulong dummy)
debug("Pinctrl init failed: %d\n", ret);
return;
}
+
+#if !defined(CONFIG_SPL_OF_PLATDATA)
+ if (of_machine_is_compatible("phytec,rk3288-phycore-som")) {
+ ret = phycore_init();
+ if (ret) {
+ debug("Failed to set up phycore power settings: %d\n",
+ ret);
+ return;
+ }
+ }
+#endif
+
debug("\nspl:init dram\n");
ret = uclass_get_device(UCLASS_RAM, 0, &dev);
if (ret) {
diff --git a/arch/arm/mach-rockchip/rk3288/Kconfig b/arch/arm/mach-rockchip/rk3288/Kconfig
index 8e7355e..53cc9a0 100644
--- a/arch/arm/mach-rockchip/rk3288/Kconfig
+++ b/arch/arm/mach-rockchip/rk3288/Kconfig
@@ -66,6 +66,14 @@ config TARGET_MIQI_RK3288
has 1 or 2 GiB SDRAM. Expansion connectors provide access to
I2C, SPI, UART, GPIOs and fan control.
+config TARGET_PHYCORE_RK3288
+ bool "phyCORE-RK3288"
+ select BOARD_LATE_INIT
+ help
+ Add basic support for the PCM-947 carrier board, a RK3288 based
+ development board made by PHYTEC. This board works in a combination
+ with the phyCORE-RK3288 System on Module.
+
config TARGET_POPMETAL_RK3288
bool "PopMetal-RK3288"
select BOARD_LATE_INIT
@@ -129,6 +137,8 @@ source "board/google/veyron/Kconfig"
source "board/mqmaker/miqi_rk3288/Kconfig"
+source "board/phytec/phycore_rk3288/Kconfig"
+
source "board/radxa/rock2/Kconfig"
source "board/rockchip/evb_rk3288/Kconfig"
diff --git a/board/phytec/phycore_rk3288/Kconfig b/board/phytec/phycore_rk3288/Kconfig
new file mode 100644
index 0000000..57cd8e2
--- /dev/null
+++ b/board/phytec/phycore_rk3288/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_PHYCORE_RK3288
+
+config SYS_BOARD
+ default "phycore_rk3288"
+
+config SYS_VENDOR
+ default "phytec"
+
+config SYS_CONFIG_NAME
+ default "phycore_rk3288"
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+ def_bool y
+
+endif
diff --git a/board/phytec/phycore_rk3288/MAINTAINERS b/board/phytec/phycore_rk3288/MAINTAINERS
new file mode 100644
index 0000000..9c0de3c
--- /dev/null
+++ b/board/phytec/phycore_rk3288/MAINTAINERS
@@ -0,0 +1,6 @@
+phyCORE-RK3288
+M: Wadim Egorov <w.egorov at phytec.de>
+S: Maintained
+F: board/phytec/phycore_rk3288
+F: include/configs/phycore_rk3288.h
+F: configs/phycore-rk3288_defconfig
diff --git a/board/phytec/phycore_rk3288/Makefile b/board/phytec/phycore_rk3288/Makefile
new file mode 100644
index 0000000..f379fbe
--- /dev/null
+++ b/board/phytec/phycore_rk3288/Makefile
@@ -0,0 +1,8 @@
+#
+# Copyright (C) 2017 PHYTEC Messtechnik GmbH
+# Author: Wadim Egorov <w.egorov at phytec.de>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += phycore-rk3288.o
diff --git a/board/phytec/phycore_rk3288/phycore-rk3288.c b/board/phytec/phycore_rk3288/phycore-rk3288.c
new file mode 100644
index 0000000..20696f6
--- /dev/null
+++ b/board/phytec/phycore_rk3288/phycore-rk3288.c
@@ -0,0 +1,8 @@
+/*
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov at phytec.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
diff --git a/configs/phycore-rk3288_defconfig b/configs/phycore-rk3288_defconfig
new file mode 100644
index 0000000..823db06
--- /dev/null
+++ b/configs/phycore-rk3288_defconfig
@@ -0,0 +1,70 @@
+CONFIG_ARM=y
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_ROCKCHIP_RK3288=y
+CONFIG_ROCKCHIP_SPL_BACK_TO_BROM=y
+CONFIG_TARGET_PHYCORE_RK3288=y
+CONFIG_SPL_STACK_R_ADDR=0x80000
+CONFIG_DEFAULT_DEVICE_TREE="rk3288-phycore-rdk"
+CONFIG_DEBUG_UART=y
+CONFIG_SILENT_CONSOLE=y
+CONFIG_CONSOLE_MUX=y
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x2000
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_POWER_SUPPORT=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_GPT=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_ISO_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_SPL_PARTITION_UUIDS=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_SPL_SYSCON=y
+# CONFIG_SPL_SIMPLE_BUS is not set
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_GMAC_ROCKCHIP=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+# CONFIG_SPL_PINCTRL_FULL is not set
+CONFIG_PINCTRL_ROCKCHIP_RK3288=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_RAM=y
+CONFIG_SPL_RAM=y
+CONFIG_DEBUG_UART_BASE=0xff690000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_USE_TINY_PRINTF=y
+CONFIG_CMD_DHRYSTONE=y
+CONFIG_ERRNO_STR=y
diff --git a/include/configs/phycore_rk3288.h b/include/configs/phycore_rk3288.h
new file mode 100644
index 0000000..aab43ed
--- /dev/null
+++ b/include/configs/phycore_rk3288.h
@@ -0,0 +1,23 @@
+/*
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov at phytec.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define ROCKCHIP_DEVICE_SETTINGS
+#include <configs/rk3288_common.h>
+
+#undef BOOT_TARGET_DEVICES
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(MMC, mmc, 1)
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 1
+
+#endif
--
1.9.1
More information about the U-Boot
mailing list