[U-Boot] [PATCH 23/31] ARM: k2g: Add pinmux support for K2G ICE evm

[Franklin S Cooper Jr]

Add basic pinmux data for new K2G ICE evm. Also add pinmuxing for a
generic K2G evm which includes I2C 0 and 1 used for board detection
purposes.

Since multiple K2G boards are supported that means initially generic
pinmuxing should be used when board detection hasn't ran. Once board
detection runs the proper pinmuxing can be reran to match the board
being ran on.

Signed-off-by: Franklin S Cooper Jr <fcooper at ti.com>
---
 board/ti/ks2_evm/board_k2g.c |  2 ++
 board/ti/ks2_evm/mux-k2g.h   | 45 +++++++++++++++++++++++++++++++++++++++++++-
 2 files changed, 46 insertions(+), 1 deletion(-)

diff --git a/board/ti/ks2_evm/board_k2g.c b/board/ti/ks2_evm/board_k2g.c
index 64b1f6b..8340cde 100644
--- a/board/ti/ks2_evm/board_k2g.c
+++ b/board/ti/ks2_evm/board_k2g.c
@@ -180,6 +180,8 @@ int embedded_dtb_select(void)
 
 	fdtdec_setup();
 
+	k2g_mux_config();
+
 	k2g_reset_mux_config();
 
 	/* deassert FLASH_HOLD */
diff --git a/board/ti/ks2_evm/mux-k2g.h b/board/ti/ks2_evm/mux-k2g.h
index 773f9b7..630103d 100644
--- a/board/ti/ks2_evm/mux-k2g.h
+++ b/board/ti/ks2_evm/mux-k2g.h
@@ -11,6 +11,22 @@
 #include <asm/io.h>
 #include <asm/arch/mux-k2g.h>
 #include <asm/arch/hardware.h>
+#include "board.h"
+
+struct pin_cfg k2g_generic_pin_cfg[] = {
+	/* UART0 */
+	{ 115,  MODE(0) },	/* SOC_UART0_RXD */
+	{ 116,  MODE(0) },	/* SOC_UART0_TXD */
+
+	/* I2C 0 */
+	{ 223,  MODE(0) },	/* SOC_I2C0_SCL */
+	{ 224,  MODE(0) },	/* SOC_I2C0_SDA */
+
+	/* I2C 1 */
+	{ 225,  MODE(0) },	/* SOC_I2C1_SCL */
+	{ 226,  MODE(0) },	/* SOC_I2C1_SDA */
+	{ MAX_PIN_N, }
+};
 
 struct pin_cfg k2g_evm_pin_cfg[] = {
 	/* GPMC */
@@ -307,7 +323,34 @@ struct pin_cfg k2g_evm_pin_cfg[] = {
 	{ MAX_PIN_N, }
 };
 
+struct pin_cfg k2g_ice_evm_pin_cfg[] = {
+	/* MMC 1 */
+	{ 63, MODE(0) | PIN_PTD },	/* MMC1_DAT3.MMC1_DAT3 */
+	{ 64, MODE(0) | PIN_PTU },	/* MMC1_DAT2.MMC1_DAT2 */
+	{ 65, MODE(0) | PIN_PTU },	/* MMC1_DAT1.MMC1_DAT1 */
+	{ 66, MODE(0) | PIN_PTD },	/* MMC1_DAT0.MMC1_DAT0 */
+	{ 67, MODE(0) | PIN_PTD },	/* MMC1_CLK.MMC1_CLK   */
+	{ 68, MODE(0) | PIN_PTD },	/* MMC1_CMD.MMC1_CMD   */
+	{ 69, MODE(3) | PIN_PTU },	/* MMC1_SDCD.GPIO0_69  */
+	{ 70, MODE(0) | PIN_PTU },	/* MMC1_SDWP.MMC1_SDWP */
+	{ 71, MODE(0) | PIN_PTD },	/* MMC1_POW.MMC1_POW   */
+
+	/* I2C 0 */
+	{ 223,  MODE(0) },		/* SOC_I2C0_SCL */
+	{ 224,  MODE(0) },		/* SOC_I2C0_SDA */
+	{ MAX_PIN_N, }
+};
+
 void k2g_mux_config(void)
 {
-	configure_pin_mux(k2g_evm_pin_cfg);
+	if (!board_ti_was_eeprom_read()) {
+		configure_pin_mux(k2g_generic_pin_cfg);
+	} else if (board_is_k2g_gp()) {
+		configure_pin_mux(k2g_evm_pin_cfg);
+	} else if (board_is_k2g_ice()) {
+		configure_pin_mux(k2g_ice_evm_pin_cfg);
+	} else {
+		puts("Unknown board, cannot configure pinmux.");
+		hang();
+	}
 }
-- 
2.10.0