[U-Boot] [linux-sunxi] [PATCH 8/8] [DO NOT MERGE] sunxi: power: add AXP803 support
Icenowy Zheng
icenowy at aosc.xyz
Wed Mar 8 23:44:35 UTC 2017
2017年3月9日 07:34于 Jernej Skrabec <jernej.skrabec at siol.net>写道：
>
> From: Icenowy Zheng <icenowy at aosc.xyz>
I'm making newer version of this patch.
>
> The A64 uses the AXP803 as its PMIC.
>
> Signed-off-by: Icenowy Zheng <icenowy at aosc.xyz>
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec at siol.net>
> ---
>
> arch/arm/mach-sunxi/Makefile | 3 +
> arch/arm/mach-sunxi/pmic_bus.c | 6 +-
> arch/arm/mach-sunxi/rsb.c | 2 +-
> board/sunxi/board.c | 31 ++---
> drivers/power/Kconfig | 87 ++++++++------
> drivers/power/Makefile | 1 +
> drivers/power/axp803.c | 256 +++++++++++++++++++++++++++++++++++++++++
> drivers/power/axp818.c | 2 +-
> include/axp803.h | 73 ++++++++++++
> include/axp_pmic.h | 3 +
> 10 files changed, 414 insertions(+), 50 deletions(-)
> create mode 100644 drivers/power/axp803.c
> create mode 100644 include/axp803.h
>
> diff --git a/arch/arm/mach-sunxi/Makefile b/arch/arm/mach-sunxi/Makefile
> index efab4811ee..861a52c6d0 100644
> --- a/arch/arm/mach-sunxi/Makefile
> +++ b/arch/arm/mach-sunxi/Makefile
> @@ -19,9 +19,11 @@ endif
> obj-$(CONFIG_MACH_SUN6I) += prcm.o
> obj-$(CONFIG_MACH_SUN8I) += prcm.o
> obj-$(CONFIG_MACH_SUN9I) += prcm.o
> +obj-$(CONFIG_MACH_SUN50I) += prcm.o
> obj-$(CONFIG_MACH_SUN6I) += p2wi.o
> obj-$(CONFIG_MACH_SUN8I) += rsb.o
> obj-$(CONFIG_MACH_SUN9I) += rsb.o
> +obj-$(CONFIG_MACH_SUN50I) += rsb.o
> obj-$(CONFIG_MACH_SUN4I) += clock_sun4i.o
> obj-$(CONFIG_MACH_SUN5I) += clock_sun4i.o
> obj-$(CONFIG_MACH_SUN6I) += clock_sun6i.o
> @@ -37,6 +39,7 @@ obj-$(CONFIG_MACH_SUN9I) += clock_sun9i.o gtbus_sun9i.o
> obj-$(CONFIG_AXP152_POWER) += pmic_bus.o
> obj-$(CONFIG_AXP209_POWER) += pmic_bus.o
> obj-$(CONFIG_AXP221_POWER) += pmic_bus.o
> +obj-$(CONFIG_AXP803_POWER) += pmic_bus.o
> obj-$(CONFIG_AXP809_POWER) += pmic_bus.o
> obj-$(CONFIG_AXP818_POWER) += pmic_bus.o
>
> diff --git a/arch/arm/mach-sunxi/pmic_bus.c b/arch/arm/mach-sunxi/pmic_bus.c
> index 7c57f02792..0ac64a97cf 100644
> --- a/arch/arm/mach-sunxi/pmic_bus.c
> +++ b/arch/arm/mach-sunxi/pmic_bus.c
> @@ -36,7 +36,7 @@ int pmic_bus_init(void)
> if (!needs_init)
> return 0;
>
> -#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
> +#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
> # ifdef CONFIG_MACH_SUN6I
> p2wi_init();
> ret = p2wi_change_to_p2wi_mode(AXP221_CHIP_ADDR, AXP221_CTRL_ADDR,
> @@ -62,7 +62,7 @@ int pmic_bus_read(u8 reg, u8 *data)
> return i2c_read(AXP152_I2C_ADDR, reg, 1, data, 1);
> #elif defined CONFIG_AXP209_POWER
> return i2c_read(AXP209_I2C_ADDR, reg, 1, data, 1);
> -#elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
> +#elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
> # ifdef CONFIG_MACH_SUN6I
> return p2wi_read(reg, data);
> # else
> @@ -77,7 +77,7 @@ int pmic_bus_write(u8 reg, u8 data)
> return i2c_write(AXP152_I2C_ADDR, reg, 1, &data, 1);
> #elif defined CONFIG_AXP209_POWER
> return i2c_write(AXP209_I2C_ADDR, reg, 1, &data, 1);
> -#elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
> +#elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
> # ifdef CONFIG_MACH_SUN6I
> return p2wi_write(reg, data);
> # else
> diff --git a/arch/arm/mach-sunxi/rsb.c b/arch/arm/mach-sunxi/rsb.c
> index 6fd11f1529..28d05e962a 100644
> --- a/arch/arm/mach-sunxi/rsb.c
> +++ b/arch/arm/mach-sunxi/rsb.c
> @@ -20,7 +20,7 @@ static int rsb_set_device_mode(void);
>
> static void rsb_cfg_io(void)
> {
> -#ifdef CONFIG_MACH_SUN8I
> +#if defined CONFIG_MACH_SUN8I || defined CONFIG_MACH_SUN50I
> sunxi_gpio_set_cfgpin(SUNXI_GPL(0), SUN8I_GPL_R_RSB);
> sunxi_gpio_set_cfgpin(SUNXI_GPL(1), SUN8I_GPL_R_RSB);
> sunxi_gpio_set_pull(SUNXI_GPL(0), 1);
> diff --git a/board/sunxi/board.c b/board/sunxi/board.c
> index b9660128e5..75e53bebbd 100644
> --- a/board/sunxi/board.c
> +++ b/board/sunxi/board.c
> @@ -487,26 +487,27 @@ void sunxi_board_init(void)
> #endif
>
> #if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
> - defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
> - defined CONFIG_AXP818_POWER
> + defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || \
> + defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
> power_failed = axp_init();
>
> -#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
> - defined CONFIG_AXP818_POWER
> +#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || \
> + defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
> power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
> #endif
> power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
> power_failed |= axp_set_dcdc3(CONFIG_AXP_DCDC3_VOLT);
> -#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP818_POWER)
> +#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP803_POWER) && \
> + !defined(CONFIG_AXP818_POWER)
> power_failed |= axp_set_dcdc4(CONFIG_AXP_DCDC4_VOLT);
> #endif
> -#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
> - defined CONFIG_AXP818_POWER
> +#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || \
> + defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
> power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
> #endif
>
> -#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
> - defined CONFIG_AXP818_POWER
> +#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || \
> + defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
> power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT);
> #endif
> power_failed |= axp_set_aldo2(CONFIG_AXP_ALDO2_VOLT);
> @@ -517,8 +518,8 @@ void sunxi_board_init(void)
> power_failed |= axp_set_aldo4(CONFIG_AXP_ALDO4_VOLT);
> #endif
>
> -#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP809_POWER) || \
> - defined(CONFIG_AXP818_POWER)
> +#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP803_POWER) || \
> + defined(CONFIG_AXP809_POWER) || defined(CONFIG_AXP818_POWER)
> power_failed |= axp_set_dldo(1, CONFIG_AXP_DLDO1_VOLT);
> power_failed |= axp_set_dldo(2, CONFIG_AXP_DLDO2_VOLT);
> #if !defined CONFIG_AXP809_POWER
> @@ -530,13 +531,17 @@ void sunxi_board_init(void)
> power_failed |= axp_set_eldo(3, CONFIG_AXP_ELDO3_VOLT);
> #endif
>
> -#ifdef CONFIG_AXP818_POWER
> +#if defined CONFIG_AXP803_POWER || defined CONFIG_AXP818_POWER
> power_failed |= axp_set_fldo(1, CONFIG_AXP_FLDO1_VOLT);
> power_failed |= axp_set_fldo(2, CONFIG_AXP_FLDO2_VOLT);
> +#endif
> +
> +#ifdef CONFIG_AXP818_POWER
> power_failed |= axp_set_fldo(3, CONFIG_AXP_FLDO3_VOLT);
> #endif
>
> -#if defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
> +#if defined CONFIG_AXP803_POWER || defined CONFIG_AXP809_POWER || \
> + defined CONFIG_AXP818_POWER
> power_failed |= axp_set_sw(IS_ENABLED(CONFIG_AXP_SW_ON));
> #endif
> #endif
> diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
> index 64e5bc2f74..4907002ed6 100644
> --- a/drivers/power/Kconfig
> +++ b/drivers/power/Kconfig
> @@ -11,8 +11,9 @@ choice
> depends on ARCH_SUNXI
> default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
> default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
> + default AXP803_POWER if MACH_SUN50I
> default AXP818_POWER if MACH_SUN8I_A83T
> - default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I
> + default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5
>
> config SUNXI_NO_PMIC
> bool "board without a pmic"
> @@ -43,6 +44,13 @@ config AXP221_POWER
> Select this to enable support for the axp221/axp223 pmic found on most
> A23 and A31 boards.
>
> +config AXP803_POWER
> + bool "axp803 pmic support"
> + depends on MACH_SUN50I
> + select CMD_POWEROFF
> + ---help---
> + Say y here to enable support for the axp803 pmic found on A64 boards.
> +
> config AXP809_POWER
> bool "axp809 pmic support"
> depends on MACH_SUN9I
> @@ -69,25 +77,25 @@ endchoice
>
> config AXP_DCDC1_VOLT
> int "axp pmic dcdc1 voltage"
> - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
> - default 3300 if AXP818_POWER
> + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
> + default 3300 if AXP818_POWER || MACH_SUN50I
> default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
> ---help---
> Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
> disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for
> generic 3.3V IO voltage for external devices like the lcd-panal and
> sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to
> - save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T
> - dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally
> - powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG.
> + save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T and
> + A64 dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1
> + normally powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG.
>
> config AXP_DCDC2_VOLT
> int "axp pmic dcdc2 voltage"
> - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
> + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
> default 900 if AXP818_POWER
> default 1400 if AXP152_POWER || AXP209_POWER
> default 1200 if MACH_SUN6I
> - default 1100 if MACH_SUN8I
> + default 1100 if MACH_SUN8I || MACH_SUN50I
> default 0 if MACH_SUN9I
> ---help---
> Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to
> @@ -97,15 +105,17 @@ config AXP_DCDC2_VOLT
> On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
> On A80 boards dcdc2 powers the GPU and can be left off.
> On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
> + On A64 boards dcdc2 is used with dcdc3 for VDD-CPU and should be 1.1V.
>
> config AXP_DCDC3_VOLT
> int "axp pmic dcdc3 voltage"
> - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
> + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
> default 900 if AXP809_POWER || AXP818_POWER
> default 1500 if AXP152_POWER
> default 1250 if AXP209_POWER
> default 1200 if MACH_SUN6I || MACH_SUN8I
> - ---help---
> + default 1100 if MACH_SUN50I
> +---help---
> Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to
> disable dcdc3.
> On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and
> @@ -114,39 +124,42 @@ config AXP_DCDC3_VOLT
> On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
> On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
> On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
> + On A64 boards dcdc3 is used with dcdc2 for VDD-CPU and should be 1.1V.
>
> config AXP_DCDC4_VOLT
> int "axp pmic dcdc4 voltage"
> - depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
> + depends on AXP152_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
> default 1250 if AXP152_POWER
> default 1200 if MACH_SUN6I
> default 0 if MACH_SUN8I
> default 900 if MACH_SUN9I
> + default 0 if MACH_SUN50I
> ---help---
> Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to
> disable dcdc4.
> On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V.
> On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V.
> - On A23 / A33 boards dcdc4 is unused and should be disabled.
> + On A23 / A33 / A64 boards dcdc4 is unused and should be disabled.
> On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V.
> On A83T boards dcdc4 is used for VDD-GPU.
>
> config AXP_DCDC5_VOLT
> int "axp pmic dcdc5 voltage"
> - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
> - default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
> + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
> + default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I || MACH_SUN50I
> ---help---
> Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
> disable dcdc5.
> - On A23 / A31 / A33 / A80 / A83T boards dcdc5 is VCC-DRAM and
> + On A23 / A31 / A33 / A64 / A80 / A83T boards dcdc5 is VCC-DRAM and
> should be 1.5V, 1.35V if DDR3L is used.
>
> config AXP_ALDO1_VOLT
> int "axp pmic (a)ldo1 voltage"
> - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
> + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
> default 0 if MACH_SUN6I
> default 1800 if MACH_SUN8I_A83T
> default 3000 if MACH_SUN8I || MACH_SUN9I
> + default 2800 if MACH_SUN50I
> ---help---
> Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to
> disable aldo1.
> @@ -155,14 +168,16 @@ config AXP_ALDO1_VOLT
> On A80 boards aldo1 powers the USB hosts and should be 3.0V.
> On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and
> should be 1.8V.
> + On A64 boards aldo1 powers PE pingroup and CSI and should be 2.8V.
>
> config AXP_ALDO2_VOLT
> int "axp pmic (a)ldo2 voltage"
> - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
> + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
> default 3000 if AXP152_POWER || AXP209_POWER
> default 0 if MACH_SUN6I || MACH_SUN9I
> default 1800 if MACH_SUN8I_A83T
> default 2500 if MACH_SUN8I
> + default 1800 if MACH_SUN50I
> ---help---
> Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to
> disable aldo2.
> @@ -173,17 +188,19 @@ config AXP_ALDO2_VOLT
> On A80 boards aldo2 powers PB pingroup and camera IO and can be left off.
> On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
> LPDDR2, and the codec. It should be 1.8V.
> + On A64 boards aldo2 powers PL pingroup and should be 1.8V.
>
> config AXP_ALDO3_VOLT
> int "axp pmic (a)ldo3 voltage"
> - depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
> + depends on AXP209_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
> default 0 if AXP209_POWER || MACH_SUN9I
> - default 3000 if MACH_SUN6I || MACH_SUN8I
> + default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN50I
> ---help---
> Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
> disable aldo3.
> On A10(s) / A13 / A20 boards aldo3 should be 2.8V.
> - On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V.
> + On A23 / A31 / A33 / A64 boards aldo3 is VCC-PLL and AVCC
> + and should be 3.0V.
> On A80 boards aldo3 is normally not used.
> On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
> 3.0V.
> @@ -199,17 +216,19 @@ config AXP_ALDO4_VOLT
>
> config AXP_DLDO1_VOLT
> int "axp pmic dldo1 voltage"
> - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
> + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
> + default 3300 if MACH_SUN50I
> default 0
> ---help---
> Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to
> disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used
> to power the ethernet phy. On A23, A33 and A80 boards this is often
> - used to power the wifi.
> + used to power the wifi. On A64 boards this is often used to power the
> + HDMI.
>
> config AXP_DLDO2_VOLT
> int "axp pmic dldo2 voltage"
> - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
> + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
> default 3000 if MACH_SUN9I
> default 0
> ---help---
> @@ -219,7 +238,7 @@ config AXP_DLDO2_VOLT
>
> config AXP_DLDO3_VOLT
> int "axp pmic dldo3 voltage"
> - depends on AXP221_POWER || AXP818_POWER
> + depends on AXP221_POWER || AXP803_POWER || AXP818_POWER
> default 0
> ---help---
> Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to
> @@ -227,7 +246,7 @@ config AXP_DLDO3_VOLT
>
> config AXP_DLDO4_VOLT
> int "axp pmic dldo4 voltage"
> - depends on AXP221_POWER || AXP818_POWER
> + depends on AXP221_POWER || AXP803_POWER || AXP818_POWER
> default 0
> ---help---
> Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to
> @@ -235,15 +254,17 @@ config AXP_DLDO4_VOLT
>
> config AXP_ELDO1_VOLT
> int "axp pmic eldo1 voltage"
> - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
> + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
> + default 1800 if MACH_SUN50I
> default 0
> ---help---
> Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to
> disable eldo1.
> + On A64 boards it's used for the codec and should be 1.8V.
>
> config AXP_ELDO2_VOLT
> int "axp pmic eldo2 voltage"
> - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
> + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
> default 0
> ---help---
> Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to
> @@ -251,7 +272,7 @@ config AXP_ELDO2_VOLT
>
> config AXP_ELDO3_VOLT
> int "axp pmic eldo3 voltage"
> - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
> + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER
> default 3000 if MACH_SUN9I
> default 0
> ---help---
> @@ -263,8 +284,8 @@ config AXP_ELDO3_VOLT
>
> config AXP_FLDO1_VOLT
> int "axp pmic fldo1 voltage"
> - depends on AXP818_POWER
> - default 0 if MACH_SUN8I_A83T
> + depends on AXP803_POWER || AXP818_POWER
> + default 0
> ---help---
> Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to
> disable fldo1.
> @@ -273,11 +294,13 @@ config AXP_FLDO1_VOLT
>
> config AXP_FLDO2_VOLT
> int "axp pmic fldo2 voltage"
> - depends on AXP818_POWER
> + depends on AXP803_POWER || AXP818_POWER
> + default 1100 if MACH_SUN50I
> default 900 if MACH_SUN8I_A83T
> ---help---
> Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to
> disable fldo2.
> + On A64 boards fldo2 is VCC-CPUS and should be 1.1V.
> On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.
>
> config AXP_FLDO3_VOLT
> @@ -290,7 +313,7 @@ config AXP_FLDO3_VOLT
>
> config AXP_SW_ON
> bool "axp pmic sw on"
> - depends on AXP809_POWER || AXP818_POWER
> + depends on AXP803_POWER || AXP809_POWER || AXP818_POWER
> default n
> ---help---
> Enable to turn on axp pmic sw.
> diff --git a/drivers/power/Makefile b/drivers/power/Makefile
> index b43523e628..1449e875ce 100644
> --- a/drivers/power/Makefile
> +++ b/drivers/power/Makefile
> @@ -9,6 +9,7 @@ obj-$(CONFIG_AS3722_POWER) += as3722.o
> obj-$(CONFIG_AXP152_POWER) += axp152.o
> obj-$(CONFIG_AXP209_POWER) += axp209.o
> obj-$(CONFIG_AXP221_POWER) += axp221.o
> +obj-$(CONFIG_AXP803_POWER) += axp803.o
> obj-$(CONFIG_AXP809_POWER) += axp809.o
> obj-$(CONFIG_AXP818_POWER) += axp818.o
> obj-$(CONFIG_EXYNOS_TMU) += exynos-tmu.o
> diff --git a/drivers/power/axp803.c b/drivers/power/axp803.c
> new file mode 100644
> index 0000000000..93b9d95234
> --- /dev/null
> +++ b/drivers/power/axp803.c
> @@ -0,0 +1,256 @@
> +/*
> + * AXP803 driver based on AXP818 driver
> + *
> + * Based on axp818.c
> + * (C) Copyright 2015 Vishnu Patekar <vishnuptekar0510 at gmail.com>
> + *
> + * Based on axp221.c
> + * (C) Copyright 2014 Hans de Goede <hdegoede at redhat.com>
> + * (C) Copyright 2013 Oliver Schinagl <oliver at schinagl.nl>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <errno.h>
> +#include <asm/arch/gpio.h>
> +#include <asm/arch/pmic_bus.h>
> +#include <axp_pmic.h>
> +
> +static u8 axp803_mvolt_to_cfg(int mvolt, int min, int max, int div)
> +{
> + if (mvolt < min)
> + mvolt = min;
> + else if (mvolt > max)
> + mvolt = max;
> +
> + return (mvolt - min) / div;
> +}
> +
> +int axp_set_dcdc1(unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg = axp803_mvolt_to_cfg(mvolt, 1600, 3400, 100);
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL1,
> + AXP803_OUTPUT_CTRL1_DCDC1_EN);
> +
> + ret = pmic_bus_write(AXP803_DCDC1_CTRL, cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP803_OUTPUT_CTRL1,
> + AXP803_OUTPUT_CTRL1_DCDC1_EN);
> +}
> +
> +int axp_set_dcdc2(unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg;
> +
> + if (mvolt >= 1220)
> + cfg = 70 + axp803_mvolt_to_cfg(mvolt, 1220, 1300, 20);
> + else
> + cfg = axp803_mvolt_to_cfg(mvolt, 500, 1200, 10);
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL1,
> + AXP803_OUTPUT_CTRL1_DCDC2_EN);
> +
> + ret = pmic_bus_write(AXP803_DCDC2_CTRL, cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP803_OUTPUT_CTRL1,
> + AXP803_OUTPUT_CTRL1_DCDC2_EN);
> +}
> +
> +int axp_set_dcdc3(unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg;
> +
> + if (mvolt >= 1220)
> + cfg = 70 + axp803_mvolt_to_cfg(mvolt, 1220, 1300, 20);
> + else
> + cfg = axp803_mvolt_to_cfg(mvolt, 500, 1200, 10);
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL1,
> + AXP803_OUTPUT_CTRL1_DCDC3_EN);
> +
> + ret = pmic_bus_write(AXP803_DCDC3_CTRL, cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP803_OUTPUT_CTRL1,
> + AXP803_OUTPUT_CTRL1_DCDC3_EN);
> +}
> +
> +int axp_set_dcdc5(unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg;
> +
> + if (mvolt >= 1140)
> + cfg = 32 + axp803_mvolt_to_cfg(mvolt, 1140, 1840, 20);
> + else
> + cfg = axp803_mvolt_to_cfg(mvolt, 800, 1120, 10);
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL1,
> + AXP803_OUTPUT_CTRL1_DCDC5_EN);
> +
> + ret = pmic_bus_write(AXP803_DCDC5_CTRL, cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP803_OUTPUT_CTRL1,
> + AXP803_OUTPUT_CTRL1_DCDC5_EN);
> +}
> +
> +int axp_set_aldo(int aldo_num, unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg;
> +
> + if (aldo_num < 1 || aldo_num > 3)
> + return -EINVAL;
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL3,
> + AXP803_OUTPUT_CTRL3_ALDO1_EN << (aldo_num - 1));
> +
> + cfg = axp803_mvolt_to_cfg(mvolt, 700, 3300, 100);
> + ret = pmic_bus_write(AXP803_ALDO1_CTRL + (aldo_num - 1), cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP803_OUTPUT_CTRL3,
> + AXP803_OUTPUT_CTRL3_ALDO1_EN << (aldo_num - 1));
> +}
> +
> +/* TODO: re-work other AXP drivers to consolidate ALDO functions. */
> +int axp_set_aldo1(unsigned int mvolt)
> +{
> + return axp_set_aldo(1, mvolt);
> +}
> +
> +int axp_set_aldo2(unsigned int mvolt)
> +{
> + return axp_set_aldo(2, mvolt);
> +}
> +
> +int axp_set_aldo3(unsigned int mvolt)
> +{
> + return axp_set_aldo(3, mvolt);
> +}
> +
> +int axp_set_dldo(int dldo_num, unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg;
> +
> + if (dldo_num < 1 || dldo_num > 4)
> + return -EINVAL;
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL2,
> + AXP803_OUTPUT_CTRL2_DLDO1_EN << (dldo_num - 1));
> +
> + cfg = axp803_mvolt_to_cfg(mvolt, 700, 3300, 100);
> + if (dldo_num == 2 && mvolt > 3300)
> + cfg += 1 + axp803_mvolt_to_cfg(mvolt, 3400, 4200, 200);
> + ret = pmic_bus_write(AXP803_DLDO1_CTRL + (dldo_num - 1), cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP803_OUTPUT_CTRL2,
> + AXP803_OUTPUT_CTRL2_DLDO1_EN << (dldo_num - 1));
> +}
> +
> +int axp_set_eldo(int eldo_num, unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg;
> +
> + if (eldo_num < 1 || eldo_num > 3)
> + return -EINVAL;
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL2,
> + AXP803_OUTPUT_CTRL2_ELDO1_EN << (eldo_num - 1));
> +
> + cfg = axp803_mvolt_to_cfg(mvolt, 700, 1900, 50);
> + ret = pmic_bus_write(AXP803_ELDO1_CTRL + (eldo_num - 1), cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP803_OUTPUT_CTRL2,
> + AXP803_OUTPUT_CTRL2_ELDO1_EN << (eldo_num - 1));
> +}
> +
> +int axp_set_fldo(int fldo_num, unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg;
> +
> + if (fldo_num < 1 || fldo_num > 2)
> + return -EINVAL;
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL3,
> + AXP803_OUTPUT_CTRL3_FLDO1_EN << (fldo_num - 1));
> +
> + cfg = axp803_mvolt_to_cfg(mvolt, 700, 1450, 50);
> + ret = pmic_bus_write(AXP803_FLDO1_CTRL + (fldo_num - 1), cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP803_OUTPUT_CTRL3,
> + AXP803_OUTPUT_CTRL3_FLDO1_EN << (fldo_num - 1));
> +}
> +
> +int axp_set_sw(bool on)
> +{
> + if (on)
> + return pmic_bus_setbits(AXP803_OUTPUT_CTRL2,
> + AXP803_OUTPUT_CTRL2_SW_EN);
> +
> + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL2,
> + AXP803_OUTPUT_CTRL2_SW_EN);
> +}
> +
> +int axp_init(void)
> +{
> + u8 axp_chip_id;
> + int ret;
> +
> + ret = pmic_bus_init();
> + if (ret)
> + return ret;
> +
> + ret = pmic_bus_read(AXP803_CHIP_ID, &axp_chip_id);
> + if (ret)
> + return ret;
> +
> + if (!(axp_chip_id == 0x51))
> + return -ENODEV;
> + else
> + return ret;
> +
> + return 0;
> +}
> +
> +int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
> +{
> + pmic_bus_write(AXP803_SHUTDOWN, AXP803_SHUTDOWN_POWEROFF);
> +
> + /* infinite loop during shutdown */
> + while (1)
> + ;
> +
> + /* not reached */
> + return 0;
> +}
> diff --git a/drivers/power/axp818.c b/drivers/power/axp818.c
> index af4d7a6903..ad0c330ca5 100644
> --- a/drivers/power/axp818.c
> +++ b/drivers/power/axp818.c
> @@ -162,7 +162,7 @@ int axp_set_dldo(int dldo_num, unsigned int mvolt)
> cfg = axp818_mvolt_to_cfg(mvolt, 700, 3300, 100);
> if (dldo_num == 2 && mvolt > 3300)
> cfg += 1 + axp818_mvolt_to_cfg(mvolt, 3400, 4200, 200);
> - ret = pmic_bus_write(AXP818_ELDO1_CTRL + (dldo_num - 1), cfg);
> + ret = pmic_bus_write(AXP818_DLDO1_CTRL + (dldo_num - 1), cfg);
> if (ret)
> return ret;
>
> diff --git a/include/axp803.h b/include/axp803.h
> new file mode 100644
> index 0000000000..b382f3a5ec
> --- /dev/null
> +++ b/include/axp803.h
> @@ -0,0 +1,73 @@
> +/*
> + * (C) Copyright 2016 Icenowy Zheng <icenowy at aosc.xyz>
> + *
> + * Based on axp818.h, which is:
> + * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510 at gmail.com>
> + *
> + * X-Powers AXP803 Power Management IC driver
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#define AXP803_CHIP_ID 0x03
> +
> +#define AXP803_OUTPUT_CTRL1 0x10
> +#define AXP803_OUTPUT_CTRL1_DCDC1_EN (1 << 0)
> +#define AXP803_OUTPUT_CTRL1_DCDC2_EN (1 << 1)
> +#define AXP803_OUTPUT_CTRL1_DCDC3_EN (1 << 2)
> +#define AXP803_OUTPUT_CTRL1_DCDC4_EN (1 << 3)
> +#define AXP803_OUTPUT_CTRL1_DCDC5_EN (1 << 4)
> +#define AXP803_OUTPUT_CTRL1_DCDC6_EN (1 << 5)
> +#define AXP803_OUTPUT_CTRL2 0x12
> +#define AXP803_OUTPUT_CTRL2_ELDO1_EN (1 << 0)
> +#define AXP803_OUTPUT_CTRL2_ELDO2_EN (1 << 1)
> +#define AXP803_OUTPUT_CTRL2_ELDO3_EN (1 << 2)
> +#define AXP803_OUTPUT_CTRL2_DLDO1_EN (1 << 3)
> +#define AXP803_OUTPUT_CTRL2_DLDO2_EN (1 << 4)
> +#define AXP803_OUTPUT_CTRL2_DLDO3_EN (1 << 5)
> +#define AXP803_OUTPUT_CTRL2_DLDO4_EN (1 << 6)
> +#define AXP803_OUTPUT_CTRL2_SW_EN (1 << 7)
> +#define AXP803_OUTPUT_CTRL3 0x13
> +#define AXP803_OUTPUT_CTRL3_FLDO1_EN (1 << 2)
> +#define AXP803_OUTPUT_CTRL3_FLDO2_EN (1 << 3)
> +#define AXP803_OUTPUT_CTRL3_ALDO1_EN (1 << 5)
> +#define AXP803_OUTPUT_CTRL3_ALDO2_EN (1 << 6)
> +#define AXP803_OUTPUT_CTRL3_ALDO3_EN (1 << 7)
> +
> +#define AXP803_DLDO1_CTRL 0x15
> +#define AXP803_DLDO2_CTRL 0x16
> +#define AXP803_DLDO3_CTRL 0x17
> +#define AXP803_DLDO4_CTRL 0x18
> +#define AXP803_ELDO1_CTRL 0x19
> +#define AXP803_ELDO2_CTRL 0x1a
> +#define AXP803_ELDO3_CTRL 0x1b
> +#define AXP803_FLDO1_CTRL 0x1c
> +#define AXP803_FLDO2_CTRL 0x1d
> +#define AXP803_DCDC1_CTRL 0x20
> +#define AXP803_DCDC2_CTRL 0x21
> +#define AXP803_DCDC3_CTRL 0x22
> +#define AXP803_DCDC4_CTRL 0x23
> +#define AXP803_DCDC5_CTRL 0x24
> +#define AXP803_DCDC6_CTRL 0x25
> +
> +#define AXP803_ALDO1_CTRL 0x28
> +#define AXP803_ALDO2_CTRL 0x29
> +#define AXP803_ALDO3_CTRL 0x2a
> +
> +#define AXP803_SHUTDOWN 0x32
> +#define AXP803_SHUTDOWN_POWEROFF (1 << 7)
> +
> +/* For axp_gpio.c */
> +#define AXP_POWER_STATUS 0x00
> +#define AXP_POWER_STATUS_VBUS_PRESENT (1 << 5)
> +#define AXP_VBUS_IPSOUT 0x30
> +#define AXP_VBUS_IPSOUT_DRIVEBUS (1 << 2)
> +#define AXP_MISC_CTRL 0x8f
> +#define AXP_MISC_CTRL_N_VBUSEN_FUNC (1 << 4)
> +#define AXP_GPIO0_CTRL 0x90
> +#define AXP_GPIO1_CTRL 0x92
> +#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
> +#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
> +#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
> +#define AXP_GPIO_STATE 0x94
> +#define AXP_GPIO_STATE_OFFSET 0
> diff --git a/include/axp_pmic.h b/include/axp_pmic.h
> index d789ad8086..8cb4d5763c 100644
> --- a/include/axp_pmic.h
> +++ b/include/axp_pmic.h
> @@ -16,6 +16,9 @@
> #ifdef CONFIG_AXP221_POWER
> #include <axp221.h>
> #endif
> +#ifdef CONFIG_AXP803_POWER
> +#include <axp803.h>
> +#endif
> #ifdef CONFIG_AXP809_POWER
> #include <axp809.h>
> #endif
> --
> 2.12.0
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe at googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
More information about the U-Boot
mailing list