[U-Boot] [PATCH 13/21] usb: dwc3: Add dwc3 support for STi
Marek Vasut
marex at denx.de
Fri Mar 17 16:42:09 UTC 2017
On 03/17/2017 05:25 PM, patrice.chotard at st.com wrote:
> From: Patrice Chotard <patrice.chotard at st.com>
>
> This patch adds the ST glue logic to manage the DWC3 HC
> on STiH407 SoC family. It configures the internal glue
> logic and syscfg registers.
>
> Part of this code been extracted from kernel.org driver
> (drivers/usb/dwc3/dwc3-st.c)
>
> Signed-off-by: Patrice Chotard <patrice.chotard at st.com>
> ---
> arch/arm/include/asm/arch-stih410/sys_proto.h | 11 +++
> drivers/usb/dwc3/Kconfig | 8 ++
> drivers/usb/dwc3/Makefile | 1 +
> drivers/usb/dwc3/dwc3-sti.c | 137 ++++++++++++++++++++++++++
> include/dwc3-sti-uboot.h | 50 ++++++++++
> 5 files changed, 207 insertions(+)
> create mode 100644 arch/arm/include/asm/arch-stih410/sys_proto.h
> create mode 100644 drivers/usb/dwc3/dwc3-sti.c
> create mode 100644 include/dwc3-sti-uboot.h
>
> diff --git a/arch/arm/include/asm/arch-stih410/sys_proto.h b/arch/arm/include/asm/arch-stih410/sys_proto.h
> new file mode 100644
> index 0000000..5c40d3b
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-stih410/sys_proto.h
> @@ -0,0 +1,11 @@
> +/*
> + * Copyright (c) 2017
> + * Patrice Chotard <patrice.chotard at st.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef _ASM_ARCH_SYS_PROTO_H
> +#define _ASM_ARCH_SYS_PROTO_H
> +
> +#endif /* _ASM_ARCH_SYS_PROTO_H */
> diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
> index e93398f..51a7a00 100644
> --- a/drivers/usb/dwc3/Kconfig
> +++ b/drivers/usb/dwc3/Kconfig
> @@ -37,6 +37,14 @@ config USB_DWC3_OMAP
>
> Say 'Y' here if you have one such device
>
> +config USB_DWC3_STI
> + bool "STMicroelectronics STiH407 family glue driver"
> + help
> + STMicroelectronics STiH407 family SoCs use this IP for
> + USB2/3 functionality.
> +
> + Say 'Y' here if you have one such device
> +
> menu "PHY Subsystem"
>
> config USB_DWC3_PHY_OMAP
> diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
> index 2964bae..753912d 100644
> --- a/drivers/usb/dwc3/Makefile
> +++ b/drivers/usb/dwc3/Makefile
> @@ -11,3 +11,4 @@ obj-$(CONFIG_USB_DWC3_GADGET) += gadget.o ep0.o
> obj-$(CONFIG_USB_DWC3_OMAP) += dwc3-omap.o
> obj-$(CONFIG_USB_DWC3_PHY_OMAP) += ti_usb_phy.o
> obj-$(CONFIG_USB_DWC3_PHY_SAMSUNG) += samsung_usb_phy.o
> +obj-$(CONFIG_USB_DWC3_STI) += dwc3-sti.o
> diff --git a/drivers/usb/dwc3/dwc3-sti.c b/drivers/usb/dwc3/dwc3-sti.c
> new file mode 100644
> index 0000000..5ff3e76
> --- /dev/null
> +++ b/drivers/usb/dwc3/dwc3-sti.c
> @@ -0,0 +1,137 @@
> +/*
> + * dwc3-sti.c - STiH407 family DWC3 specific Glue layer
> + * Copyright (c) 2017
> + * Patrice Chotard <patrice.chotard at st.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <asm/io.h>
> +#include <common.h>
> +#include <dm.h>
> +#include <dwc3-sti-uboot.h>
> +#include <fdtdec.h>
> +#include <regmap.h>
> +#include <syscon.h>
> +#include <usb.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +__weak int __board_usb_init(int index, enum usb_init_type init)
> +{
> + return 0;
> +}
> +/*int board_usb_init(int index, enum usb_init_type init)*/
> +/* __attribute__((weak, alias("__board_usb_init")));*/
> +
> +static int sti_dwc3_drd_init(struct sti_dwc3_platdata *plat)
> +{
> + unsigned long val;
> +
> + val = readl(plat->syscfg_base + plat->syscfg_offset);
> +
> + val &= USB3_CONTROL_MASK;
> +
> + switch (plat->mode) {
> + case USB_DR_MODE_PERIPHERAL:
> + val &= ~(USB3_DELAY_VBUSVALID
> + | USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3)
> + | USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2
> + | USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
> +
> + val |= USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID;
> + break;
> +
> + case USB_DR_MODE_HOST:
> + val &= ~(USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID
> + | USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3)
> + | USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2
> + | USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
> +
> + val |= USB3_DELAY_VBUSVALID;
> + break;
> +
> + default:
> + error("Unsupported mode of operation %d\n", plat->mode);
> + return -EINVAL;
> + }
> + return writel(val, plat->syscfg_base + plat->syscfg_offset);
> +}
> +
> +static void sti_dwc3_init(struct sti_dwc3_platdata *plat)
> +{
> + unsigned long reg;
> +
> + reg = readl(plat->glue_base + CLKRST_CTRL);
> +
> + reg |= AUX_CLK_EN | EXT_CFG_RESET_N | XHCI_REVISION;
> + reg &= ~SW_PIPEW_RESET_N;
> +
> + writel(reg, plat->glue_base + CLKRST_CTRL);
> +
> + /* configure mux for vbus, powerpresent and bvalid signals */
> + reg = readl(plat->glue_base + USB2_VBUS_MNGMNT_SEL1);
> +
> + reg |= SEL_OVERRIDE_VBUSVALID(USB2_VBUS_UTMIOTG) |
> + SEL_OVERRIDE_POWERPRESENT(USB2_VBUS_UTMIOTG) |
> + SEL_OVERRIDE_BVALID(USB2_VBUS_UTMIOTG);
> +
> + writel(reg, plat->glue_base + USB2_VBUS_MNGMNT_SEL1);
> +
> + reg = readl(plat->glue_base + CLKRST_CTRL);
> + reg |= SW_PIPEW_RESET_N;
> + writel(reg, plat->glue_base + CLKRST_CTRL);
setbits_le32() ?
> +}
> +
> +int sti_dwc3_glue_init(enum usb_dr_mode mode)
> +{
> + struct sti_dwc3_platdata plat;
> + struct fdtdec_phandle_args syscfg_phandle;
> + struct udevice *syscon;
> + struct regmap *regmap;
> + int node, ret;
> + const void *blob = gd->fdt_blob;
> + u32 reg[4];
> +
> + /* find the dwc3 node */
> + node = fdt_node_offset_by_compatible(blob, -1, "st,stih407-dwc3");
> +
> + ret = fdtdec_get_int_array(blob, node, "reg", reg, ARRAY_SIZE(reg));
> + if (ret) {
> + error("unable to find st,stih407-dwc3 reg property(%d)\n", ret);
> + return ret;
> + }
> +
> + plat.glue_base = reg[0];
> + plat.syscfg_offset = reg[2];
> + plat.mode = mode;
> +
> + /* get corresponding syscon phandle */
> + ret = fdtdec_parse_phandle_with_args(gd->fdt_blob, node,
> + "st,syscfg", NULL, 0, 0,
> + &syscfg_phandle);
> + if (ret < 0) {
> + error("Can't get syscfg phandle: %d\n", ret);
> + return ret;
> + }
> +
> + ret = uclass_get_device_by_of_offset(UCLASS_SYSCON, syscfg_phandle.node,
> + &syscon);
> + if (ret) {
> + error("unable to find syscon device (%d)\n", ret);
> + return ret;
> + }
> +
> + /* get syscfg-reg base address */
> + regmap = syscon_get_regmap(syscon);
> + if (!regmap) {
> + error("unable to find regmap\n");
> + return -ENODEV;
> + }
> + plat.syscfg_base = regmap->base;
> +
> + sti_dwc3_drd_init(&plat);
> + sti_dwc3_init(&plat);
> +
> + return 0;
> +}
> diff --git a/include/dwc3-sti-uboot.h b/include/dwc3-sti-uboot.h
> new file mode 100644
> index 0000000..c7bb770
> --- /dev/null
> +++ b/include/dwc3-sti-uboot.h
> @@ -0,0 +1,50 @@
> +/*
> + * Copyright (c) 2017
> + * Patrice Chotard <patrice.chotard at st.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __DWC3_STI_UBOOT_H_
> +#define __DWC3_STI_UBOOT_H_
> +
> +#include <linux/usb/otg.h>
> +
> +/* glue registers */
> +#define CLKRST_CTRL 0x00
> +#define AUX_CLK_EN BIT(0)
> +#define SW_PIPEW_RESET_N BIT(4)
> +#define EXT_CFG_RESET_N BIT(8)
> +
> +#define XHCI_REVISION BIT(12)
> +
> +#define USB2_VBUS_MNGMNT_SEL1 0x2C
> +#define USB2_VBUS_UTMIOTG 0x1
> +
> +#define SEL_OVERRIDE_VBUSVALID(n) (n << 0)
> +#define SEL_OVERRIDE_POWERPRESENT(n) (n << 4)
> +#define SEL_OVERRIDE_BVALID(n) (n << 8)
> +
> +/* Static DRD configuration */
> +#define USB3_CONTROL_MASK 0xf77
> +
> +#define USB3_DEVICE_NOT_HOST BIT(0)
> +#define USB3_FORCE_VBUSVALID BIT(1)
> +#define USB3_DELAY_VBUSVALID BIT(2)
> +#define USB3_SEL_FORCE_OPMODE BIT(4)
> +#define USB3_FORCE_OPMODE(n) (n << 5)
The (n) should be in parenthesis ...
> +#define USB3_SEL_FORCE_DPPULLDOWN2 BIT(8)
> +#define USB3_FORCE_DPPULLDOWN2 BIT(9)
> +#define USB3_SEL_FORCE_DMPULLDOWN2 BIT(10)
> +#define USB3_FORCE_DMPULLDOWN2 BIT(11)
> +
> +struct sti_dwc3_platdata {
> + phys_addr_t syscfg_base;
> + phys_addr_t glue_base;
> + phys_addr_t syscfg_offset;
> + enum usb_dr_mode mode;
> +};
> +
> +int sti_dwc3_glue_init(enum usb_dr_mode mode);
> +
> +#endif /* __DWC3_STI_UBOOT_H_ */
>
--
Best regards,
Marek Vasut
More information about the U-Boot
mailing list