[U-Boot] [PATCH v5 2/4] ARM: at91: dt: add dts file for sama5d3 Xplained
Wenyou Yang
wenyou.yang at atmel.com
Thu Mar 23 05:20:42 UTC 2017
Add the device tree file for sama5d3 Xplained board.
The dts files are copied from the Linux-4.9, do changes as below.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
---
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/arm/dts/Makefile | 3 +
arch/arm/dts/at91-sama5d3_xplained.dts | 348 +++++++++++++++++++++++++++++++++
2 files changed, 351 insertions(+)
create mode 100644 arch/arm/dts/at91-sama5d3_xplained.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index afed460ac9..1273767ac0 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -336,6 +336,9 @@ dtb-$(CONFIG_TARGET_SAMA5D3XEK) += \
sama5d36ek.dtb \
sama5d36ek_cmp.dtb
+dtb-$(CONFIG_TARGET_SAMA5D3_XPLAINED) += \
+ at91-sama5d3_xplained.dtb
+
dtb-$(CONFIG_ARCH_BCM283X) += \
bcm2835-rpi-a-plus.dtb \
bcm2835-rpi-a.dtb \
diff --git a/arch/arm/dts/at91-sama5d3_xplained.dts b/arch/arm/dts/at91-sama5d3_xplained.dts
new file mode 100644
index 0000000000..69597102fb
--- /dev/null
+++ b/arch/arm/dts/at91-sama5d3_xplained.dts
@@ -0,0 +1,348 @@
+/*
+ * at91-sama5d3_xplained.dts - Device Tree file for the SAMA5D3 Xplained board
+ *
+ * Copyright (C) 2014 Atmel,
+ * 2014 Nicolas Ferre <nicolas.ferre at atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "sama5d36.dtsi"
+
+/ {
+ model = "SAMA5D3 Xplained";
+ compatible = "atmel,sama5d3-xplained", "atmel,sama5d3", "atmel,sama5";
+
+ chosen {
+ u-boot,dm-pre-reloc;
+ stdout-path = &dbgu;
+ };
+
+ aliases {
+ spi0 = &spi0;
+ };
+
+ memory {
+ reg = <0x20000000 0x10000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ mmc0: mmc at f0000000 {
+ u-boot,dm-pre-reloc;
+ pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd>;
+ vmmc-supply = <&vcc_mmc0_reg>;
+ vqmmc-supply = <&vcc_3v3_reg>;
+ status = "okay";
+ slot at 0 {
+ reg = <0>;
+ bus-width = <8>;
+ cd-gpios = <&pioE 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ mmc1: mmc at f8000000 {
+ u-boot,dm-pre-reloc;
+ vmmc-supply = <&vcc_3v3_reg>;
+ vqmmc-supply = <&vcc_3v3_reg>;
+ status = "disabled";
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioE 1 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ spi0: spi at f0004000 {
+ cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
+ status = "okay";
+ };
+
+ can0: can at f000c000 {
+ status = "okay";
+ };
+
+ i2c0: i2c at f0014000 {
+ pinctrl-0 = <&pinctrl_i2c0_pu>;
+ status = "okay";
+ };
+
+ i2c1: i2c at f0018000 {
+ status = "okay";
+
+ pmic: act8865 at 5b {
+ compatible = "active-semi,act8865";
+ reg = <0x5b>;
+ status = "disabled";
+
+ regulators {
+ vcc_1v8_reg: DCDC_REG1 {
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vcc_1v2_reg: DCDC_REG2 {
+ regulator-name = "VCC_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ vcc_3v3_reg: DCDC_REG3 {
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vddfuse_reg: LDO_REG1 {
+ regulator-name = "FUSE_2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ vddana_reg: LDO_REG2 {
+ regulator-name = "VDDANA";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+ };
+
+ macb0: ethernet at f0028000 {
+ phy-mode = "rgmii";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ ethernet-phy at 7 {
+ reg = <0x7>;
+ };
+ };
+
+ pwm0: pwm at f002c000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_pwmh0_0 &pinctrl_pwm0_pwmh1_0>;
+ status = "okay";
+ };
+
+ usart0: serial at f001c000 {
+ status = "okay";
+ };
+
+ usart1: serial at f0020000 {
+ pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+ status = "okay";
+ };
+
+ uart0: serial at f0024000 {
+ status = "okay";
+ };
+
+ mmc1: mmc at f8000000 {
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+ status = "okay";
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioE 1 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ spi1: spi at f8008000 {
+ cs-gpios = <&pioC 25 0>;
+ status = "okay";
+ };
+
+ adc0: adc at f8018000 {
+ pinctrl-0 = <
+ &pinctrl_adc0_adtrg
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad1
+ &pinctrl_adc0_ad2
+ &pinctrl_adc0_ad3
+ &pinctrl_adc0_ad4
+ &pinctrl_adc0_ad5
+ &pinctrl_adc0_ad6
+ &pinctrl_adc0_ad7
+ &pinctrl_adc0_ad8
+ &pinctrl_adc0_ad9
+ >;
+ status = "okay";
+ };
+
+ i2c2: i2c at f801c000 {
+ dmas = <0>, <0>; /* Do not use DMA for i2c2 */
+ pinctrl-0 = <&pinctrl_i2c2_pu>;
+ status = "okay";
+ };
+
+ macb1: ethernet at f802c000 {
+ phy-mode = "rmii";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ ethernet-phy at 1 {
+ reg = <0x1>;
+ };
+ };
+
+ dbgu: serial at ffffee00 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+ };
+
+ pinctrl at fffff200 {
+ board {
+ u-boot,dm-pre-reloc;
+ pinctrl_i2c0_pu: i2c0_pu {
+ atmel,pins =
+ <AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+ <AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_i2c2_pu: i2c2_pu {
+ atmel,pins =
+ <AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>,
+ <AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_key_gpio: key_gpio_0 {
+ atmel,pins =
+ <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+
+ pinctrl_mmc0_cd: mmc0_cd {
+ u-boot,dm-pre-reloc;
+ atmel,pins =
+ <AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+
+ pinctrl_mmc1_cd: mmc1_cd {
+ u-boot,dm-pre-reloc;
+ atmel,pins =
+ <AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PE9, conflicts with A9 */
+ };
+ };
+ };
+ };
+
+ nand0: nand at 60000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <4>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+ status = "okay";
+
+ at91bootstrap at 0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader at 40000 {
+ label = "bootloader";
+ reg = <0x40000 0x80000>;
+ };
+
+ bootloaderenv at c0000 {
+ label = "bootloader env";
+ reg = <0xc0000 0xc0000>;
+ };
+
+ dtb at 180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel at 200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs at 800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+ };
+
+ usb0: gadget at 00500000 {
+ atmel,vbus-gpio = <&pioE 9 GPIO_ACTIVE_HIGH>; /* PE9, conflicts with A9 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+
+ usb1: ohci at 00600000 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <0
+ &pioE 3 GPIO_ACTIVE_LOW
+ &pioE 4 GPIO_ACTIVE_LOW
+ >;
+ status = "okay";
+ };
+
+ usb2: ehci at 00700000 {
+ status = "okay";
+ };
+ };
+
+ vcc_mmc0_reg: fixedregulator at 0 {
+ compatible = "regulator-fixed";
+ gpio = <&pioE 2 GPIO_ACTIVE_LOW>;
+ regulator-name = "mmc0-card-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_key_gpio>;
+
+ bp3 {
+ label = "PB_USER";
+ gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
+ linux,code = <0x104>;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ d2 {
+ label = "d2";
+ gpios = <&pioE 23 GPIO_ACTIVE_LOW>; /* PE23, conflicts with A23, CTS2 */
+ linux,default-trigger = "heartbeat";
+ };
+
+ d3 {
+ label = "d3";
+ gpios = <&pioE 24 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
--
2.11.0
More information about the U-Boot
mailing list