[U-Boot] [PATCH v5 4/4] ARM: dts: at91: add dts file for sama5d4ek
Wenyou Yang
wenyou.yang at atmel.com
Thu Mar 23 05:20:44 UTC 2017
Add the device tree file for sama5d4ek board.
The dts file is copied from Linux-4.4, do the following changes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warning.
Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
---
Changes in v5:
- Integrate the dts patches for sama5d3 to one.
- Add the "u-boot,dm-pre-reloc" property for SPL.
- Update the commit log.
- Rebase on v2017.03.
Changes in v4:
- Rebase on the master branch on git://git.denx.de/u-boot-atmel.git
commit: 0ff27d4a94637d4b1937c625d33212375bd118d9
Changes in v3:
- Fix the compatible of spi flash, use "spi-flash".
Changes in v2:
- Remove unneeded the pinctrl node for cs pin of spi0.
arch/arm/dts/Makefile | 3 +
arch/arm/dts/at91-sama5d4ek.dts | 341 ++++++++++++++++++++++++++++++++++++++++
2 files changed, 344 insertions(+)
create mode 100644 arch/arm/dts/at91-sama5d4ek.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 3d661fda69..4b6215aa32 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -339,6 +339,9 @@ dtb-$(CONFIG_TARGET_SAMA5D3XEK) += \
dtb-$(CONFIG_TARGET_SAMA5D3_XPLAINED) += \
at91-sama5d3_xplained.dtb
+dtb-$(CONFIG_TARGET_SAMA5D4EK) += \
+ at91-sama5d4ek.dtb
+
dtb-$(CONFIG_TARGET_SAMA5D4_XPLAINED) += \
at91-sama5d4_xplained.dtb
diff --git a/arch/arm/dts/at91-sama5d4ek.dts b/arch/arm/dts/at91-sama5d4ek.dts
new file mode 100644
index 0000000000..b965f5b39d
--- /dev/null
+++ b/arch/arm/dts/at91-sama5d4ek.dts
@@ -0,0 +1,341 @@
+/*
+ * at91-sama5d4ek.dts - Device Tree file for SAMA5D4 Evaluation Kit
+ *
+ * Copyright (C) 2014 Atmel,
+ * 2014 Nicolas Ferre <nicolas.ferre at atmel.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "sama5d4.dtsi"
+
+/ {
+ model = "Atmel SAMA5D4-EK";
+ compatible = "atmel,sama5d4ek", "atmel,sama5d4", "atmel,sama5";
+
+ aliases {
+ spi0 = &spi0;
+ };
+
+ chosen {
+ u-boot,dm-pre-reloc;
+ stdout-path = &usart3;
+ };
+
+
+ memory {
+ reg = <0x20000000 0x20000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ adc0: adc at fc034000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ /* external trigger conflicts with USBA_VBUS */
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad1
+ &pinctrl_adc0_ad2
+ &pinctrl_adc0_ad3
+ &pinctrl_adc0_ad4
+ >;
+ /* The vref depends on JP22 of EK. If connect 1-2 then use 3.3V. connect 2-3 use 3.0V */
+ atmel,adc-vref = <3300>;
+ /*atmel,adc-ts-wires = <4>;*/ /* Set up ADC touch screen */
+ status = "okay"; /* Enable ADC IIO support */
+ };
+
+ mmc0: mmc at f8000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioE 5 0>;
+ };
+ };
+
+ ssc0: ssc at f8008000 {
+ status = "okay";
+ };
+
+ spi0: spi at f8010000 {
+ u-boot,dm-pre-reloc;
+ cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
+ status = "okay";
+ spi_flash at 0 {
+ u-boot,dm-pre-reloc;
+ compatible = "spi-flash";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+ };
+
+ i2c0: i2c at f8014000 {
+ status = "okay";
+
+ wm8904: codec at 1a {
+ compatible = "wlf,wm8904";
+ reg = <0x1a>;
+ clocks = <&pck2>;
+ clock-names = "mclk";
+ };
+
+ qt1070:keyboard at 1b {
+ compatible = "qt1070";
+ reg = <0x1b>;
+ interrupt-parent = <&pioE>;
+ interrupts = <25 0x0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qt1070_irq>;
+ wakeup-source;
+ };
+
+ atmel_mxt_ts at 4c {
+ compatible = "atmel,atmel_mxt_ts";
+ reg = <0x4c>;
+ interrupt-parent = <&pioE>;
+ interrupts = <24 0x0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mxt_ts>;
+ };
+ };
+
+ macb0: ethernet at f8020000 {
+ pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>;
+ phy-mode = "rmii";
+ status = "okay";
+
+ ethernet-phy at 1 {
+ reg = <0x1>;
+ interrupt-parent = <&pioE>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+
+ mmc1: mmc at fc000000 {
+ u-boot,dm-pre-reloc;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+ status = "okay";
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioE 6 0>;
+ };
+ };
+
+ usart2: serial at fc008000 {
+ status = "okay";
+ };
+
+ usart3: serial at fc00c000 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+ };
+
+ usart4: serial at fc010000 {
+ status = "okay";
+ };
+
+ watchdog at fc068640 {
+ status = "okay";
+ };
+
+ pinctrl at fc06a000 {
+ board {
+ u-boot,dm-pre-reloc;
+ pinctrl_macb0_phy_irq: macb0_phy_irq {
+ atmel,pins =
+ <AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ pinctrl_mmc0_cd: mmc0_cd {
+ atmel,pins =
+ <AT91_PIOE 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ pinctrl_mmc1_cd: mmc1_cd {
+ u-boot,dm-pre-reloc;
+ atmel,pins =
+ <AT91_PIOE 6 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ pinctrl_pck2_as_audio_mck: pck2_as_audio_mck {
+ atmel,pins =
+ <AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+ };
+ pinctrl_key_gpio: key_gpio_0 {
+ atmel,pins =
+ <AT91_PIOE 13 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PE13 gpio */
+ };
+ pinctrl_qt1070_irq: qt1070_irq {
+ atmel,pins =
+ <AT91_PIOE 25 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ pinctrl_mxt_ts: mxt_irq {
+ atmel,pins =
+ <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ };
+ };
+ };
+
+ usb0: gadget at 00400000 {
+ atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+
+ usb1: ohci at 00500000 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <0 /* &pioE 10 GPIO_ACTIVE_LOW */
+ &pioE 11 GPIO_ACTIVE_LOW
+ &pioE 12 GPIO_ACTIVE_LOW
+ >;
+ status = "okay";
+ };
+
+ usb2: ehci at 00600000 {
+ status = "okay";
+ };
+
+ nand0: nand at 80000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-on-flash-bbt;
+ atmel,has-pmecc;
+ status = "okay";
+
+ at91bootstrap at 0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader at 40000 {
+ label = "bootloader";
+ reg = <0x40000 0x80000>;
+ };
+
+ bootloaderenv at c0000 {
+ label = "bootloader env";
+ reg = <0xc0000 0xc0000>;
+ };
+
+ dtb at 180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel at 200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs at 800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_key_gpio>;
+
+ pb_user1 {
+ label = "pb_user1";
+ gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
+ linux,code = <0x100>;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ status = "okay";
+
+ d8 {
+ label = "d8";
+ /* PE28, conflicts with usart4 rts pin */
+ gpios = <&pioE 28 GPIO_ACTIVE_LOW>;
+ };
+
+ d9 {
+ label = "d9";
+ gpios = <&pioE 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ d10 {
+ label = "d10";
+ gpios = <&pioE 8 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ sound {
+ compatible = "atmel,asoc-wm8904";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck2_as_audio_mck>;
+
+ atmel,model = "wm8904 @ SAMA5D4EK";
+ atmel,audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "IN1L", "Line In Jack",
+ "IN1R", "Line In Jack";
+
+ atmel,ssc-controller = <&ssc0>;
+ atmel,audio-codec = <&wm8904>;
+ };
+};
--
2.11.0
More information about the U-Boot
mailing list