[U-Boot] [PATCH 3/7] arm: socfpga: Restructure FPGA driver in the preparation to support A10.
Marek Vasut
marex at denx.de
Fri May 5 11:13:24 UTC 2017
On 05/05/2017 12:26 PM, tien.fong.chee at intel.com wrote:
> From: Tien Fong Chee <tien.fong.chee at intel.com>
>
> Move FPGA driver which is Gen5 specific code into Gen5 files.
> No functional change.
It's a driver, so it should stay in drivers/ . If you need to split it,
split it in drivers/fpga/ and add Kconfig option(s)
> Signed-off-by: Tien Fong Chee <tien.fong.chee at intel.com>
> ---
> arch/arm/mach-socfpga/Makefile | 2 +-
> arch/arm/mach-socfpga/include/mach/fpga_manager.h | 65 +----
> .../mach/{fpga_manager.h => fpga_manager_gen5.h} | 69 +++---
> drivers/Makefile | 1 +
> drivers/fpga/Makefile | 1 +
> drivers/fpga/socfpga.c | 267 +-------------------
> drivers/fpga/{socfpga.c => socfpga_gen5.c} | 29 +--
> 7 files changed, 48 insertions(+), 386 deletions(-)
> copy arch/arm/mach-socfpga/include/mach/{fpga_manager.h => fpga_manager_gen5.h} (57%)
> copy drivers/fpga/{socfpga.c => socfpga_gen5.c} (92%)
>
> diff --git a/arch/arm/mach-socfpga/Makefile b/arch/arm/mach-socfpga/Makefile
> index 41b779c..286bfef 100644
> --- a/arch/arm/mach-socfpga/Makefile
> +++ b/arch/arm/mach-socfpga/Makefile
> @@ -9,7 +9,6 @@
>
> obj-y += board.o
> obj-y += clock_manager.o
> -obj-y += fpga_manager.o
> obj-y += misc.o
> obj-y += reset_manager.o
> obj-y += timer.o
> @@ -21,6 +20,7 @@ obj-y += reset_manager_gen5.o
> obj-y += scan_manager.o
> obj-y += system_manager_gen5.o
> obj-y += wrap_pll_config.o
> +obj-y += fpga_manager.o
> endif
>
> ifdef CONFIG_TARGET_SOCFPGA_ARRIA10
> diff --git a/arch/arm/mach-socfpga/include/mach/fpga_manager.h b/arch/arm/mach-socfpga/include/mach/fpga_manager.h
> index a077e22..69d8613 100644
> --- a/arch/arm/mach-socfpga/include/mach/fpga_manager.h
> +++ b/arch/arm/mach-socfpga/include/mach/fpga_manager.h
> @@ -1,5 +1,5 @@
> /*
> - * Copyright (C) 2012 Altera Corporation <www.altera.com>
> + * Copyright (C) 2012-2017 Altera Corporation <www.altera.com>
> * All rights reserved.
> *
> * SPDX-License-Identifier: BSD-3-Clause
> @@ -10,58 +10,9 @@
>
> #include <altera.h>
>
> -struct socfpga_fpga_manager {
> - /* FPGA Manager Module */
> - u32 stat; /* 0x00 */
> - u32 ctrl;
> - u32 dclkcnt;
> - u32 dclkstat;
> - u32 gpo; /* 0x10 */
> - u32 gpi;
> - u32 misci; /* 0x18 */
> - u32 _pad_0x1c_0x82c[517];
> -
> - /* Configuration Monitor (MON) Registers */
> - u32 gpio_inten; /* 0x830 */
> - u32 gpio_intmask;
> - u32 gpio_inttype_level;
> - u32 gpio_int_polarity;
> - u32 gpio_intstatus; /* 0x840 */
> - u32 gpio_raw_intstatus;
> - u32 _pad_0x848;
> - u32 gpio_porta_eoi;
> - u32 gpio_ext_porta; /* 0x850 */
> - u32 _pad_0x854_0x85c[3];
> - u32 gpio_1s_sync; /* 0x860 */
> - u32 _pad_0x864_0x868[2];
> - u32 gpio_ver_id_code;
> - u32 gpio_config_reg2; /* 0x870 */
> - u32 gpio_config_reg1;
> -};
> -
> -#define FPGAMGRREGS_STAT_MODE_MASK 0x7
> -#define FPGAMGRREGS_STAT_MSEL_MASK 0xf8
> -#define FPGAMGRREGS_STAT_MSEL_LSB 3
> -
> -#define FPGAMGRREGS_CTRL_CFGWDTH_MASK 0x200
> -#define FPGAMGRREGS_CTRL_AXICFGEN_MASK 0x100
> -#define FPGAMGRREGS_CTRL_NCONFIGPULL_MASK 0x4
> -#define FPGAMGRREGS_CTRL_NCE_MASK 0x2
> -#define FPGAMGRREGS_CTRL_EN_MASK 0x1
> -#define FPGAMGRREGS_CTRL_CDRATIO_LSB 6
> -
> -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_CRC_MASK 0x8
> -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_ID_MASK 0x4
> -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_CD_MASK 0x2
> -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_NS_MASK 0x1
> -
> -/* FPGA Mode */
> -#define FPGAMGRREGS_MODE_FPGAOFF 0x0
> -#define FPGAMGRREGS_MODE_RESETPHASE 0x1
> -#define FPGAMGRREGS_MODE_CFGPHASE 0x2
> -#define FPGAMGRREGS_MODE_INITPHASE 0x3
> -#define FPGAMGRREGS_MODE_USERMODE 0x4
> -#define FPGAMGRREGS_MODE_UNKNOWN 0x5
> +#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
> +#include <asm/arch/fpga_manager_gen5.h>
> +#endif
>
> /* FPGA CD Ratio Value */
> #define CDRATIO_x1 0x0
> @@ -74,4 +25,12 @@ int fpgamgr_test_fpga_ready(void);
> int fpgamgr_poll_fpga_ready(void);
> int fpgamgr_get_mode(void);
>
> +#define FPGA_TIMEOUT_CNT 0x1000000
> +
> +#ifndef __ASSEMBLY__
> +
> +/* Common prototypes */
> +int fpgamgr_dclkcnt_set(unsigned long cnt);
> +
> +#endif /* __ASSEMBLY__ */
> #endif /* _FPGA_MANAGER_H_ */
> diff --git a/arch/arm/mach-socfpga/include/mach/fpga_manager.h b/arch/arm/mach-socfpga/include/mach/fpga_manager_gen5.h
> similarity index 57%
> copy from arch/arm/mach-socfpga/include/mach/fpga_manager.h
> copy to arch/arm/mach-socfpga/include/mach/fpga_manager_gen5.h
> index a077e22..2de7a11 100644
> --- a/arch/arm/mach-socfpga/include/mach/fpga_manager.h
> +++ b/arch/arm/mach-socfpga/include/mach/fpga_manager_gen5.h
> @@ -1,14 +1,38 @@
> /*
> - * Copyright (C) 2012 Altera Corporation <www.altera.com>
> + * Copyright (C) 2012-2017 Altera Corporation <www.altera.com>
> * All rights reserved.
> *
> * SPDX-License-Identifier: BSD-3-Clause
> */
>
> -#ifndef _FPGA_MANAGER_H_
> -#define _FPGA_MANAGER_H_
> +#ifndef _FPGA_MANAGER_GEN5_H_
> +#define _FPGA_MANAGER_GEN5_H_
>
> -#include <altera.h>
> +#define FPGAMGRREGS_STAT_MODE_MASK 0x7
> +#define FPGAMGRREGS_STAT_MSEL_MASK 0xf8
> +#define FPGAMGRREGS_STAT_MSEL_LSB 3
> +
> +#define FPGAMGRREGS_CTRL_CFGWDTH_MASK BIT(9)
> +#define FPGAMGRREGS_CTRL_AXICFGEN_MASK BIT(8)
> +#define FPGAMGRREGS_CTRL_NCONFIGPULL_MASK BIT(2)
> +#define FPGAMGRREGS_CTRL_NCE_MASK BIT(1)
> +#define FPGAMGRREGS_CTRL_EN_MASK BIT(0)
> +#define FPGAMGRREGS_CTRL_CDRATIO_LSB 6
> +
> +#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_CRC_MASK BIT(3)
> +#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_ID_MASK BIT(2)
> +#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_CD_MASK BIT(1)
> +#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_NS_MASK BIT(0)
> +
> +/* FPGA Mode */
> +#define FPGAMGRREGS_MODE_FPGAOFF 0x0
> +#define FPGAMGRREGS_MODE_RESETPHASE 0x1
> +#define FPGAMGRREGS_MODE_CFGPHASE 0x2
> +#define FPGAMGRREGS_MODE_INITPHASE 0x3
> +#define FPGAMGRREGS_MODE_USERMODE 0x4
> +#define FPGAMGRREGS_MODE_UNKNOWN 0x5
> +
> +#ifndef __ASSEMBLY__
>
> struct socfpga_fpga_manager {
> /* FPGA Manager Module */
> @@ -39,39 +63,6 @@ struct socfpga_fpga_manager {
> u32 gpio_config_reg1;
> };
>
> -#define FPGAMGRREGS_STAT_MODE_MASK 0x7
> -#define FPGAMGRREGS_STAT_MSEL_MASK 0xf8
> -#define FPGAMGRREGS_STAT_MSEL_LSB 3
> -
> -#define FPGAMGRREGS_CTRL_CFGWDTH_MASK 0x200
> -#define FPGAMGRREGS_CTRL_AXICFGEN_MASK 0x100
> -#define FPGAMGRREGS_CTRL_NCONFIGPULL_MASK 0x4
> -#define FPGAMGRREGS_CTRL_NCE_MASK 0x2
> -#define FPGAMGRREGS_CTRL_EN_MASK 0x1
> -#define FPGAMGRREGS_CTRL_CDRATIO_LSB 6
> -
> -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_CRC_MASK 0x8
> -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_ID_MASK 0x4
> -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_CD_MASK 0x2
> -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_NS_MASK 0x1
> -
> -/* FPGA Mode */
> -#define FPGAMGRREGS_MODE_FPGAOFF 0x0
> -#define FPGAMGRREGS_MODE_RESETPHASE 0x1
> -#define FPGAMGRREGS_MODE_CFGPHASE 0x2
> -#define FPGAMGRREGS_MODE_INITPHASE 0x3
> -#define FPGAMGRREGS_MODE_USERMODE 0x4
> -#define FPGAMGRREGS_MODE_UNKNOWN 0x5
> -
> -/* FPGA CD Ratio Value */
> -#define CDRATIO_x1 0x0
> -#define CDRATIO_x2 0x1
> -#define CDRATIO_x4 0x2
> -#define CDRATIO_x8 0x3
> -
> -/* SoCFPGA support functions */
> -int fpgamgr_test_fpga_ready(void);
> -int fpgamgr_poll_fpga_ready(void);
> -int fpgamgr_get_mode(void);
> +#endif /* __ASSEMBLY__ */
>
> -#endif /* _FPGA_MANAGER_H_ */
> +#endif /* _FPGA_MANAGER_GEN5_H_ */
> diff --git a/drivers/Makefile b/drivers/Makefile
> index 4a4b237..b4a2230 100644
> --- a/drivers/Makefile
> +++ b/drivers/Makefile
> @@ -47,6 +47,7 @@ obj-$(CONFIG_OMAP_USB_PHY) += usb/phy/
> obj-$(CONFIG_SPL_SATA_SUPPORT) += block/
> obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += block/
> obj-$(CONFIG_SPL_MMC_SUPPORT) += block/
> +obj-$(CONFIG_FPGA) += fpga/
> endif
>
> ifdef CONFIG_TPL_BUILD
> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
> index 84e7605..649b6d1 100644
> --- a/drivers/fpga/Makefile
> +++ b/drivers/fpga/Makefile
> @@ -19,4 +19,5 @@ obj-$(CONFIG_FPGA_ACEX1K) += ACEX1K.o
> obj-$(CONFIG_FPGA_CYCLON2) += cyclon2.o
> obj-$(CONFIG_FPGA_STRATIX_II) += stratixII.o
> obj-$(CONFIG_FPGA_STRATIX_V) += stratixv.o
> +obj-$(CONFIG_TARGET_SOCFPGA_GEN5) += socfpga_gen5.o
> endif
> diff --git a/drivers/fpga/socfpga.c b/drivers/fpga/socfpga.c
> index f1b2f2c..30ebee8 100644
> --- a/drivers/fpga/socfpga.c
> +++ b/drivers/fpga/socfpga.c
> @@ -1,5 +1,5 @@
> /*
> - * Copyright (C) 2012 Altera Corporation <www.altera.com>
> + * Copyright (C) 2012-2017 Altera Corporation <www.altera.com>
> * All rights reserved.
> *
> * SPDX-License-Identifier: BSD-3-Clause
> @@ -14,23 +14,10 @@
>
> DECLARE_GLOBAL_DATA_PTR;
>
> -/* Timeout count */
> -#define FPGA_TIMEOUT_CNT 0x1000000
> -
> static struct socfpga_fpga_manager *fpgamgr_regs =
> (struct socfpga_fpga_manager *)SOCFPGA_FPGAMGRREGS_ADDRESS;
> -static struct socfpga_system_manager *sysmgr_regs =
> - (struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS;
> -
> -/* Set CD ratio */
> -static void fpgamgr_set_cd_ratio(unsigned long ratio)
> -{
> - clrsetbits_le32(&fpgamgr_regs->ctrl,
> - 0x3 << FPGAMGRREGS_CTRL_CDRATIO_LSB,
> - (ratio & 0x3) << FPGAMGRREGS_CTRL_CDRATIO_LSB);
> -}
>
> -static int fpgamgr_dclkcnt_set(unsigned long cnt)
> +int fpgamgr_dclkcnt_set(unsigned long cnt)
> {
> unsigned long i;
>
> @@ -52,253 +39,3 @@ static int fpgamgr_dclkcnt_set(unsigned long cnt)
>
> return -ETIMEDOUT;
> }
> -
> -/* Start the FPGA programming by initialize the FPGA Manager */
> -static int fpgamgr_program_init(void)
> -{
> - unsigned long msel, i;
> -
> - /* Get the MSEL value */
> - msel = readl(&fpgamgr_regs->stat);
> - msel &= FPGAMGRREGS_STAT_MSEL_MASK;
> - msel >>= FPGAMGRREGS_STAT_MSEL_LSB;
> -
> - /*
> - * Set the cfg width
> - * If MSEL[3] = 1, cfg width = 32 bit
> - */
> - if (msel & 0x8) {
> - setbits_le32(&fpgamgr_regs->ctrl,
> - FPGAMGRREGS_CTRL_CFGWDTH_MASK);
> -
> - /* To determine the CD ratio */
> - /* MSEL[1:0] = 0, CD Ratio = 1 */
> - if ((msel & 0x3) == 0x0)
> - fpgamgr_set_cd_ratio(CDRATIO_x1);
> - /* MSEL[1:0] = 1, CD Ratio = 4 */
> - else if ((msel & 0x3) == 0x1)
> - fpgamgr_set_cd_ratio(CDRATIO_x4);
> - /* MSEL[1:0] = 2, CD Ratio = 8 */
> - else if ((msel & 0x3) == 0x2)
> - fpgamgr_set_cd_ratio(CDRATIO_x8);
> -
> - } else { /* MSEL[3] = 0 */
> - clrbits_le32(&fpgamgr_regs->ctrl,
> - FPGAMGRREGS_CTRL_CFGWDTH_MASK);
> -
> - /* To determine the CD ratio */
> - /* MSEL[1:0] = 0, CD Ratio = 1 */
> - if ((msel & 0x3) == 0x0)
> - fpgamgr_set_cd_ratio(CDRATIO_x1);
> - /* MSEL[1:0] = 1, CD Ratio = 2 */
> - else if ((msel & 0x3) == 0x1)
> - fpgamgr_set_cd_ratio(CDRATIO_x2);
> - /* MSEL[1:0] = 2, CD Ratio = 4 */
> - else if ((msel & 0x3) == 0x2)
> - fpgamgr_set_cd_ratio(CDRATIO_x4);
> - }
> -
> - /* To enable FPGA Manager configuration */
> - clrbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_NCE_MASK);
> -
> - /* To enable FPGA Manager drive over configuration line */
> - setbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_EN_MASK);
> -
> - /* Put FPGA into reset phase */
> - setbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_NCONFIGPULL_MASK);
> -
> - /* (1) wait until FPGA enter reset phase */
> - for (i = 0; i < FPGA_TIMEOUT_CNT; i++) {
> - if (fpgamgr_get_mode() == FPGAMGRREGS_MODE_RESETPHASE)
> - break;
> - }
> -
> - /* If not in reset state, return error */
> - if (fpgamgr_get_mode() != FPGAMGRREGS_MODE_RESETPHASE) {
> - puts("FPGA: Could not reset\n");
> - return -1;
> - }
> -
> - /* Release FPGA from reset phase */
> - clrbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_NCONFIGPULL_MASK);
> -
> - /* (2) wait until FPGA enter configuration phase */
> - for (i = 0; i < FPGA_TIMEOUT_CNT; i++) {
> - if (fpgamgr_get_mode() == FPGAMGRREGS_MODE_CFGPHASE)
> - break;
> - }
> -
> - /* If not in configuration state, return error */
> - if (fpgamgr_get_mode() != FPGAMGRREGS_MODE_CFGPHASE) {
> - puts("FPGA: Could not configure\n");
> - return -2;
> - }
> -
> - /* Clear all interrupts in CB Monitor */
> - writel(0xFFF, &fpgamgr_regs->gpio_porta_eoi);
> -
> - /* Enable AXI configuration */
> - setbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_AXICFGEN_MASK);
> -
> - return 0;
> -}
> -
> -/* Write the RBF data to FPGA Manager */
> -static void fpgamgr_program_write(const void *rbf_data, unsigned long rbf_size)
> -{
> - uint32_t src = (uint32_t)rbf_data;
> - uint32_t dst = SOCFPGA_FPGAMGRDATA_ADDRESS;
> -
> - /* Number of loops for 32-byte long copying. */
> - uint32_t loops32 = rbf_size / 32;
> - /* Number of loops for 4-byte long copying + trailing bytes */
> - uint32_t loops4 = DIV_ROUND_UP(rbf_size % 32, 4);
> -
> - asm volatile(
> - "1: ldmia %0!, {r0-r7}\n"
> - " stmia %1!, {r0-r7}\n"
> - " sub %1, #32\n"
> - " subs %2, #1\n"
> - " bne 1b\n"
> - " cmp %3, #0\n"
> - " beq 3f\n"
> - "2: ldr %2, [%0], #4\n"
> - " str %2, [%1]\n"
> - " subs %3, #1\n"
> - " bne 2b\n"
> - "3: nop\n"
> - : "+r"(src), "+r"(dst), "+r"(loops32), "+r"(loops4) :
> - : "r0", "r1", "r2", "r3", "r4", "r5", "r6", "r7", "cc");
> -}
> -
> -/* Ensure the FPGA entering config done */
> -static int fpgamgr_program_poll_cd(void)
> -{
> - const uint32_t mask = FPGAMGRREGS_MON_GPIO_EXT_PORTA_NS_MASK |
> - FPGAMGRREGS_MON_GPIO_EXT_PORTA_CD_MASK;
> - unsigned long reg, i;
> -
> - /* (3) wait until full config done */
> - for (i = 0; i < FPGA_TIMEOUT_CNT; i++) {
> - reg = readl(&fpgamgr_regs->gpio_ext_porta);
> -
> - /* Config error */
> - if (!(reg & mask)) {
> - printf("FPGA: Configuration error.\n");
> - return -3;
> - }
> -
> - /* Config done without error */
> - if (reg & mask)
> - break;
> - }
> -
> - /* Timeout happened, return error */
> - if (i == FPGA_TIMEOUT_CNT) {
> - printf("FPGA: Timeout waiting for program.\n");
> - return -4;
> - }
> -
> - /* Disable AXI configuration */
> - clrbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_AXICFGEN_MASK);
> -
> - return 0;
> -}
> -
> -/* Ensure the FPGA entering init phase */
> -static int fpgamgr_program_poll_initphase(void)
> -{
> - unsigned long i;
> -
> - /* Additional clocks for the CB to enter initialization phase */
> - if (fpgamgr_dclkcnt_set(0x4))
> - return -5;
> -
> - /* (4) wait until FPGA enter init phase or user mode */
> - for (i = 0; i < FPGA_TIMEOUT_CNT; i++) {
> - if (fpgamgr_get_mode() == FPGAMGRREGS_MODE_INITPHASE)
> - break;
> - if (fpgamgr_get_mode() == FPGAMGRREGS_MODE_USERMODE)
> - break;
> - }
> -
> - /* If not in configuration state, return error */
> - if (i == FPGA_TIMEOUT_CNT)
> - return -6;
> -
> - return 0;
> -}
> -
> -/* Ensure the FPGA entering user mode */
> -static int fpgamgr_program_poll_usermode(void)
> -{
> - unsigned long i;
> -
> - /* Additional clocks for the CB to exit initialization phase */
> - if (fpgamgr_dclkcnt_set(0x5000))
> - return -7;
> -
> - /* (5) wait until FPGA enter user mode */
> - for (i = 0; i < FPGA_TIMEOUT_CNT; i++) {
> - if (fpgamgr_get_mode() == FPGAMGRREGS_MODE_USERMODE)
> - break;
> - }
> - /* If not in configuration state, return error */
> - if (i == FPGA_TIMEOUT_CNT)
> - return -8;
> -
> - /* To release FPGA Manager drive over configuration line */
> - clrbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_EN_MASK);
> -
> - return 0;
> -}
> -
> -/*
> - * FPGA Manager to program the FPGA. This is the interface used by FPGA driver.
> - * Return 0 for sucess, non-zero for error.
> - */
> -int socfpga_load(Altera_desc *desc, const void *rbf_data, size_t rbf_size)
> -{
> - unsigned long status;
> -
> - if ((uint32_t)rbf_data & 0x3) {
> - puts("FPGA: Unaligned data, realign to 32bit boundary.\n");
> - return -EINVAL;
> - }
> -
> - /* Prior programming the FPGA, all bridges need to be shut off */
> -
> - /* Disable all signals from hps peripheral controller to fpga */
> - writel(0, &sysmgr_regs->fpgaintfgrp_module);
> -
> - /* Disable all signals from FPGA to HPS SDRAM */
> -#define SDR_CTRLGRP_FPGAPORTRST_ADDRESS 0x5080
> - writel(0, SOCFPGA_SDR_ADDRESS + SDR_CTRLGRP_FPGAPORTRST_ADDRESS);
> -
> - /* Disable all axi bridge (hps2fpga, lwhps2fpga & fpga2hps) */
> - socfpga_bridges_reset(1);
> -
> - /* Unmap the bridges from NIC-301 */
> - writel(0x1, SOCFPGA_L3REGS_ADDRESS);
> -
> - /* Initialize the FPGA Manager */
> - status = fpgamgr_program_init();
> - if (status)
> - return status;
> -
> - /* Write the RBF data to FPGA Manager */
> - fpgamgr_program_write(rbf_data, rbf_size);
> -
> - /* Ensure the FPGA entering config done */
> - status = fpgamgr_program_poll_cd();
> - if (status)
> - return status;
> -
> - /* Ensure the FPGA entering init phase */
> - status = fpgamgr_program_poll_initphase();
> - if (status)
> - return status;
> -
> - /* Ensure the FPGA entering user mode */
> - return fpgamgr_program_poll_usermode();
> -}
> diff --git a/drivers/fpga/socfpga.c b/drivers/fpga/socfpga_gen5.c
> similarity index 92%
> copy from drivers/fpga/socfpga.c
> copy to drivers/fpga/socfpga_gen5.c
> index f1b2f2c..6992d83 100644
> --- a/drivers/fpga/socfpga.c
> +++ b/drivers/fpga/socfpga_gen5.c
> @@ -1,5 +1,5 @@
> /*
> - * Copyright (C) 2012 Altera Corporation <www.altera.com>
> + * Copyright (C) 2012-2017 Altera Corporation <www.altera.com>
> * All rights reserved.
> *
> * SPDX-License-Identifier: BSD-3-Clause
> @@ -14,9 +14,6 @@
>
> DECLARE_GLOBAL_DATA_PTR;
>
> -/* Timeout count */
> -#define FPGA_TIMEOUT_CNT 0x1000000
> -
> static struct socfpga_fpga_manager *fpgamgr_regs =
> (struct socfpga_fpga_manager *)SOCFPGA_FPGAMGRREGS_ADDRESS;
> static struct socfpga_system_manager *sysmgr_regs =
> @@ -30,29 +27,6 @@ static void fpgamgr_set_cd_ratio(unsigned long ratio)
> (ratio & 0x3) << FPGAMGRREGS_CTRL_CDRATIO_LSB);
> }
>
> -static int fpgamgr_dclkcnt_set(unsigned long cnt)
> -{
> - unsigned long i;
> -
> - /* Clear any existing done status */
> - if (readl(&fpgamgr_regs->dclkstat))
> - writel(0x1, &fpgamgr_regs->dclkstat);
> -
> - /* Write the dclkcnt */
> - writel(cnt, &fpgamgr_regs->dclkcnt);
> -
> - /* Wait till the dclkcnt done */
> - for (i = 0; i < FPGA_TIMEOUT_CNT; i++) {
> - if (!readl(&fpgamgr_regs->dclkstat))
> - continue;
> -
> - writel(0x1, &fpgamgr_regs->dclkstat);
> - return 0;
> - }
> -
> - return -ETIMEDOUT;
> -}
> -
> /* Start the FPGA programming by initialize the FPGA Manager */
> static int fpgamgr_program_init(void)
> {
> @@ -267,7 +241,6 @@ int socfpga_load(Altera_desc *desc, const void *rbf_data, size_t rbf_size)
> }
>
> /* Prior programming the FPGA, all bridges need to be shut off */
> -
> /* Disable all signals from hps peripheral controller to fpga */
> writel(0, &sysmgr_regs->fpgaintfgrp_module);
>
>
--
Best regards,
Marek Vasut
More information about the U-Boot
mailing list