[U-Boot] [PATCH v2 2/3] armv8: layerscape: Adjust memory mapping for Flash/SD card on LS1043A

Alison Wang b18965 at freescale.com
Tue May 16 02:45:58 UTC 2017


This patch is to adjust the memory mapping for FLash/SD card on
LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN
firmware load address, QE firmware load address, U-Boot start address on
serial flash and environment address.

Signed-off-by: Alison Wang <alison.wang at nxp.com>
---
Changes:
- Update the comments.

 arch/arm/cpu/armv8/fsl-layerscape/Kconfig |  8 ++++----
 include/configs/ls1043a_common.h          | 12 ++++++------
 include/configs/ls1043aqds.h              | 10 +++++-----
 include/configs/ls1043ardb.h              |  8 ++++----
 4 files changed, 19 insertions(+), 19 deletions(-)

diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
index 4c16c4c..82c76e2 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
+++ b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
@@ -163,11 +163,11 @@ endchoice
 config SYS_LS_PPA_FW_ADDR
 	hex "Address of PPA firmware loading from"
 	depends on FSL_LS_PPA
-	default 0x40500000 if SYS_LS_PPA_FW_IN_XIP && QSPI_BOOT
+	default 0x40400000 if SYS_LS_PPA_FW_IN_XIP && QSPI_BOOT
 	default 0x580a00000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS2080A
-	default 0x60500000 if SYS_LS_PPA_FW_IN_XIP
-	default 0x500000 if SYS_LS_PPA_FW_IN_MMC
-	default 0x500000 if SYS_LS_PPA_FW_IN_NAND
+	default 0x60400000 if SYS_LS_PPA_FW_IN_XIP
+	default 0x400000 if SYS_LS_PPA_FW_IN_MMC
+	default 0x400000 if SYS_LS_PPA_FW_IN_NAND
 
 	help
 	  If the PPA firmware locate at XIP flash, such as NOR or
diff --git a/include/configs/ls1043a_common.h b/include/configs/ls1043a_common.h
index e269248..05419fe 100644
--- a/include/configs/ls1043a_common.h
+++ b/include/configs/ls1043a_common.h
@@ -208,20 +208,20 @@
 #define CONFIG_SYS_FM_MURAM_SIZE	0x60000
 
 #ifdef CONFIG_NAND_BOOT
-/* Store Fman ucode at offeset 0x160000(11 blocks). */
+/* Store Fman ucode at offeset 0x900000(72 blocks). */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_FMAN_FW_ADDR		(11 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR		(72 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SD_BOOT)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
  * about 1MB (2040 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 2080(0x820).
+ * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 18432(0x4800).
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_FMAN_FW_ADDR		(512 * 0x820)
+#define CONFIG_SYS_FMAN_FW_ADDR		(512 * 0x4800)
 #elif defined(CONFIG_QSPI_BOOT)
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_FMAN_FW_ADDR		0x400d0000
+#define CONFIG_SYS_FMAN_FW_ADDR		0x40900000
 #define CONFIG_ENV_SPI_BUS		0
 #define CONFIG_ENV_SPI_CS		0
 #define CONFIG_ENV_SPI_MAX_HZ		1000000
@@ -229,7 +229,7 @@
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 /* FMan fireware Pre-load address */
-#define CONFIG_SYS_FMAN_FW_ADDR		0x60300000
+#define CONFIG_SYS_FMAN_FW_ADDR		0x60900000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
diff --git a/include/configs/ls1043aqds.h b/include/configs/ls1043aqds.h
index b14e944..04d74ac 100644
--- a/include/configs/ls1043aqds.h
+++ b/include/configs/ls1043aqds.h
@@ -12,7 +12,7 @@
 #if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
 #define CONFIG_SYS_TEXT_BASE		0x82000000
 #elif defined(CONFIG_QSPI_BOOT)
-#define CONFIG_SYS_TEXT_BASE		0x40010000
+#define CONFIG_SYS_TEXT_BASE		0x40100000
 #else
 #define CONFIG_SYS_TEXT_BASE		0x60100000
 #endif
@@ -413,20 +413,20 @@ unsigned long get_board_ddr_clk(void);
 #ifdef CONFIG_NAND_BOOT
 #define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_SIZE			0x2000
-#define CONFIG_ENV_OFFSET		(10 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_OFFSET		(24 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SD_BOOT)
-#define CONFIG_ENV_OFFSET		(1024 * 1024)
+#define CONFIG_ENV_OFFSET		(3 * 1024 * 1024)
 #define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV		0
 #define CONFIG_ENV_SIZE			0x2000
 #elif defined(CONFIG_QSPI_BOOT)
 #define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_ENV_SIZE			0x2000          /* 8KB */
-#define CONFIG_ENV_OFFSET		0x100000        /* 1MB */
+#define CONFIG_ENV_OFFSET		0x300000        /* 3MB */
 #define CONFIG_ENV_SECT_SIZE		0x10000
 #else
 #define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x200000)
+#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x300000)
 #define CONFIG_ENV_SECT_SIZE		0x20000
 #define CONFIG_ENV_SIZE			0x20000
 #endif
diff --git a/include/configs/ls1043ardb.h b/include/configs/ls1043ardb.h
index 5e570cd..a162378 100644
--- a/include/configs/ls1043ardb.h
+++ b/include/configs/ls1043ardb.h
@@ -235,15 +235,15 @@
 #if defined(CONFIG_NAND_BOOT)
 #define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_SIZE			0x2000
-#define CONFIG_ENV_OFFSET		(10 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_OFFSET		(24 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SD_BOOT)
-#define CONFIG_ENV_OFFSET		(1024 * 1024)
+#define CONFIG_ENV_OFFSET		(3 * 1024 * 1024)
 #define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV		0
 #define CONFIG_ENV_SIZE			0x2000
 #else
 #define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x200000)
+#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x300000)
 #define CONFIG_ENV_SECT_SIZE		0x20000
 #define CONFIG_ENV_SIZE			0x20000
 #endif
@@ -281,7 +281,7 @@
 	!defined(CONFIG_QSPI_BOOT)
 #define CONFIG_U_QE
 #endif
-#define CONFIG_SYS_QE_FW_ADDR     0x60600000
+#define CONFIG_SYS_QE_FW_ADDR     0x60940000
 #endif
 
 /* USB */
-- 
2.1.0.27.g96db324



More information about the U-Boot mailing list