[U-Boot] [PATCH v2 09/48] Drop digital thermometer and thermostat (DTT) drivers
Simon Glass
sjg at chromium.org
Tue May 16 23:38:29 UTC 2017
This subsystem is quite old. It has been replaced with a driver-model
version (UCLASS_THERMAL). Boards are free to convert to that if required,
but here is a removal patch that could be applied in the meantime.
Signed-off-by: Simon Glass <sjg at chromium.org>
Reviewed-by: Heiko Schocher <hs at denx.de>
---
Changes in v2: None
README | 6 --
board/gdsys/405ep/dlvision-10g.c | 10 ++-
board/gdsys/405ep/io.c | 10 ++-
board/gdsys/405ep/neo.c | 10 ++-
board/gdsys/405ex/io64.c | 10 ++-
cmd/Makefile | 1 -
cmd/dtt.c | 120 ---------------------------
drivers/Kconfig | 2 -
drivers/Makefile | 1 -
drivers/hwmon/Kconfig | 0
drivers/hwmon/Makefile | 22 -----
drivers/hwmon/adm1021.c | 164 -------------------------------------
drivers/hwmon/adt7460.c | 73 -----------------
drivers/hwmon/ds1621.c | 155 -----------------------------------
drivers/hwmon/ds1722.c | 137 -------------------------------
drivers/hwmon/ds1775.c | 126 ----------------------------
drivers/hwmon/ds620.c | 65 ---------------
drivers/hwmon/lm63.c | 160 ------------------------------------
drivers/hwmon/lm73.c | 146 ---------------------------------
drivers/hwmon/lm75.c | 139 -------------------------------
drivers/hwmon/lm81.c | 111 -------------------------
include/config_cmd_all.h | 1 -
include/configs/PMC440.h | 21 -----
include/configs/TQM834x.h | 8 --
include/configs/UCP1020.h | 21 -----
include/configs/acadia.h | 9 --
include/configs/canyonlands.h | 11 ---
include/configs/dlvision-10g.h | 8 --
include/configs/dlvision.h | 1 -
include/configs/exynos5-common.h | 2 -
include/configs/intip.h | 8 --
include/configs/io.h | 6 --
include/configs/io64.h | 9 --
include/configs/katmai.h | 25 ------
include/configs/kilauea.h | 4 -
include/configs/km/km-powerpc.h | 1 -
include/configs/km/km83xx-common.h | 7 --
include/configs/km82xx.h | 7 --
include/configs/makalu.h | 5 --
include/configs/motionpro.h | 8 +-
include/configs/neo.h | 8 --
include/configs/odroid_xu3.h | 1 -
include/configs/sequoia.h | 9 --
include/configs/socrates.h | 8 --
include/configs/tqma6.h | 10 ---
include/configs/tqma6_mba6.h | 2 -
include/configs/tqma6_wru4.h | 4 -
include/configs/work_92105.h | 8 --
include/configs/xilinx-ppc.h | 1 -
include/configs/xpedite517x.h | 3 -
include/configs/xpedite537x.h | 3 -
include/configs/xpedite550x.h | 3 -
include/configs/yosemite.h | 9 --
include/dtt.h | 47 -----------
include/i2c.h | 3 -
scripts/config_whitelist.txt | 22 -----
56 files changed, 35 insertions(+), 1736 deletions(-)
delete mode 100644 cmd/dtt.c
delete mode 100644 drivers/hwmon/Kconfig
delete mode 100644 drivers/hwmon/Makefile
delete mode 100644 drivers/hwmon/adm1021.c
delete mode 100644 drivers/hwmon/adt7460.c
delete mode 100644 drivers/hwmon/ds1621.c
delete mode 100644 drivers/hwmon/ds1722.c
delete mode 100644 drivers/hwmon/ds1775.c
delete mode 100644 drivers/hwmon/ds620.c
delete mode 100644 drivers/hwmon/lm63.c
delete mode 100644 drivers/hwmon/lm73.c
delete mode 100644 drivers/hwmon/lm75.c
delete mode 100644 drivers/hwmon/lm81.c
delete mode 100644 include/dtt.h
diff --git a/README b/README
index b58911da49..3d45b29bd5 100644
--- a/README
+++ b/README
@@ -830,7 +830,6 @@ The following options need to be configured:
CONFIG_CMD_CRC32 * crc32
CONFIG_CMD_DHCP * DHCP support
CONFIG_CMD_DIAG * Diagnostics
- CONFIG_CMD_DTT * Digital Therm and Thermostat
CONFIG_CMD_ECHO echo arguments
CONFIG_CMD_EDITENV edit env variable
CONFIG_CMD_EEPROM * EEPROM read/write support
@@ -2324,11 +2323,6 @@ The following options need to be configured:
If defined, then this indicates the I2C bus number for the RTC.
If not defined, then U-Boot assumes that RTC is on I2C bus 0.
- CONFIG_SYS_DTT_BUS_NUM
-
- If defined, then this indicates the I2C bus number for the DTT.
- If not defined, then U-Boot assumes that DTT is on I2C bus 0.
-
CONFIG_SOFT_I2C_READ_REPEATED_START
defining this will force the i2c_read() function in
diff --git a/board/gdsys/405ep/dlvision-10g.c b/board/gdsys/405ep/dlvision-10g.c
index e400d1945a..b531786653 100644
--- a/board/gdsys/405ep/dlvision-10g.c
+++ b/board/gdsys/405ep/dlvision-10g.c
@@ -10,7 +10,6 @@
#include <asm/processor.h>
#include <asm/io.h>
#include <asm/ppc4xx-gpio.h>
-#include <dtt.h>
#include "405ep.h"
#include <gdsys_fpga.h>
@@ -61,8 +60,13 @@ struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;
int misc_init_r(void)
{
- /* startup fans */
- dtt_init();
+ /*
+ * Note: DTT has been removed. Please use UCLASS_THERMAL.
+ *
+ * startup fans
+ *
+ * dtt_init();
+ */
return 0;
}
diff --git a/board/gdsys/405ep/io.c b/board/gdsys/405ep/io.c
index 81b49659ff..1484469bb0 100644
--- a/board/gdsys/405ep/io.c
+++ b/board/gdsys/405ep/io.c
@@ -11,7 +11,6 @@
#include <asm/io.h>
#include <asm/ppc4xx-gpio.h>
-#include <dtt.h>
#include <miiphy.h>
#include "405ep.h"
@@ -41,8 +40,13 @@ struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;
int misc_init_r(void)
{
- /* startup fans */
- dtt_init();
+ /*
+ * Note: DTT has been removed. Please use UCLASS_THERMAL.
+ *
+ * startup fans
+ *
+ * dtt_init();
+ */
return 0;
}
diff --git a/board/gdsys/405ep/neo.c b/board/gdsys/405ep/neo.c
index ff0edb2547..ad88af2d46 100644
--- a/board/gdsys/405ep/neo.c
+++ b/board/gdsys/405ep/neo.c
@@ -10,7 +10,6 @@
#include <asm/processor.h>
#include <asm/io.h>
#include <asm/ppc4xx-gpio.h>
-#include <dtt.h>
#include "405ep.h"
#include <gdsys_fpga.h>
@@ -32,8 +31,13 @@ struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;
int misc_init_r(void)
{
- /* startup fans */
- dtt_init();
+ /*
+ * Note: DTT has been removed. Please use UCLASS_THERMAL.
+ *
+ * startup fans
+ *
+ * dtt_init();
+ */
return 0;
}
diff --git a/board/gdsys/405ex/io64.c b/board/gdsys/405ex/io64.c
index 0a7baaa9db..9ef965bbfa 100644
--- a/board/gdsys/405ex/io64.c
+++ b/board/gdsys/405ex/io64.c
@@ -26,7 +26,6 @@
#include <miiphy.h>
#include <i2c.h>
-#include <dtt.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -70,8 +69,13 @@ static inline void blank_string(int size)
*/
int misc_init_r(void)
{
- /* startup fans */
- dtt_init();
+ /*
+ * Note: DTT has been removed. Please use UCLASS_THERMAL.
+ *
+ * startup fans
+ *
+ * dtt_init();
+ */
#ifdef CONFIG_ENV_IS_IN_FLASH
/* Monitor protection ON by default */
diff --git a/cmd/Makefile b/cmd/Makefile
index e98786807b..f043407656 100644
--- a/cmd/Makefile
+++ b/cmd/Makefile
@@ -43,7 +43,6 @@ ifdef CONFIG_POST
obj-$(CONFIG_CMD_DIAG) += diag.o
endif
obj-$(CONFIG_CMD_DISPLAY) += display.o
-obj-$(CONFIG_CMD_DTT) += dtt.o
obj-$(CONFIG_CMD_ECHO) += echo.o
obj-$(CONFIG_ENV_IS_IN_EEPROM) += eeprom.o
obj-$(CONFIG_CMD_EEPROM) += eeprom.o
diff --git a/cmd/dtt.c b/cmd/dtt.c
deleted file mode 100644
index dd427a3d0b..0000000000
--- a/cmd/dtt.c
+++ /dev/null
@@ -1,120 +0,0 @@
-/*
- * (C) Copyright 2001
- * Erik Theisen, Wave 7 Optics, etheisen at mindspring.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <config.h>
-#include <command.h>
-
-#include <dtt.h>
-#include <i2c.h>
-#include <tmu.h>
-#include <linux/bug.h>
-
-#if defined CONFIG_DTT_SENSORS
-static unsigned long sensor_initialized;
-
-static void _initialize_dtt(void)
-{
- int i;
- unsigned char sensors[] = CONFIG_DTT_SENSORS;
-
- for (i = 0; i < sizeof(sensors); i++) {
- if ((sensor_initialized & (1 << i)) == 0) {
- if (dtt_init_one(sensors[i]) != 0) {
- printf("DTT%d: Failed init!\n", i);
- continue;
- }
- sensor_initialized |= (1 << i);
- }
- }
-}
-
-void dtt_init(void)
-{
- int old_bus;
-
- /* switch to correct I2C bus */
- old_bus = I2C_GET_BUS();
- I2C_SET_BUS(CONFIG_SYS_DTT_BUS_NUM);
-
- _initialize_dtt();
-
- /* switch back to original I2C bus */
- I2C_SET_BUS(old_bus);
-}
-#endif
-
-int dtt_i2c(void)
-{
-#if defined CONFIG_DTT_SENSORS
- int i;
- unsigned char sensors[] = CONFIG_DTT_SENSORS;
- int old_bus;
-
- /* Force a compilation error, if there are more then 32 sensors */
- BUILD_BUG_ON(sizeof(sensors) > 32);
- /* switch to correct I2C bus */
-#ifdef CONFIG_SYS_I2C
- old_bus = i2c_get_bus_num();
- i2c_set_bus_num(CONFIG_SYS_DTT_BUS_NUM);
-#else
- old_bus = I2C_GET_BUS();
- I2C_SET_BUS(CONFIG_SYS_DTT_BUS_NUM);
-#endif
-
- _initialize_dtt();
-
- /*
- * Loop through sensors, read
- * temperature, and output it.
- */
- for (i = 0; i < sizeof(sensors); i++)
- printf("DTT%d: %i C\n", i + 1, dtt_get_temp(sensors[i]));
-
- /* switch back to original I2C bus */
-#ifdef CONFIG_SYS_I2C
- i2c_set_bus_num(old_bus);
-#else
- I2C_SET_BUS(old_bus);
-#endif
-#endif
-
- return 0;
-}
-
-int dtt_tmu(void)
-{
-#if defined CONFIG_TMU_CMD_DTT
- int cur_temp;
-
- /* Sense and return latest thermal info */
- if (tmu_monitor(&cur_temp) == TMU_STATUS_INIT) {
- puts("TMU is in unknown state, temperature is invalid\n");
- return -1;
- }
- printf("Current temperature: %u degrees Celsius\n", cur_temp);
-#endif
- return 0;
-}
-
-int do_dtt(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
-{
- int err = 0;
-
- err |= dtt_i2c();
- err |= dtt_tmu();
-
- return err;
-} /* do_dtt() */
-
-/***************************************************/
-
-U_BOOT_CMD(
- dtt, 1, 1, do_dtt,
- "Read temperature from Digital Thermometer and Thermostat",
- ""
-);
diff --git a/drivers/Kconfig b/drivers/Kconfig
index a5f24d72da..a736386a0d 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -30,8 +30,6 @@ source "drivers/fpga/Kconfig"
source "drivers/gpio/Kconfig"
-source "drivers/hwmon/Kconfig"
-
source "drivers/i2c/Kconfig"
source "drivers/input/Kconfig"
diff --git a/drivers/Makefile b/drivers/Makefile
index 25e42362ce..fa4e61a31d 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -74,7 +74,6 @@ obj-$(CONFIG_CPU) += cpu/
obj-y += crypto/
obj-y += firmware/
obj-$(CONFIG_FPGA) += fpga/
-obj-y += hwmon/
obj-y += misc/
obj-y += pcmcia/
obj-y += dfu/
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
deleted file mode 100644
index e69de29bb2..0000000000
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
deleted file mode 100644
index b4fb057c16..0000000000
--- a/drivers/hwmon/Makefile
+++ /dev/null
@@ -1,22 +0,0 @@
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# (C) Copyright 2001
-# Erik Theisen, Wave 7 Optics, etheisen at mindspring.com.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-#ccflags-y += -DDEBUG
-
-obj-$(CONFIG_DTT_ADM1021) += adm1021.o
-obj-$(CONFIG_DTT_ADT7460) += adt7460.o
-obj-$(CONFIG_DTT_DS1621) += ds1621.o
-obj-$(CONFIG_DTT_DS1722) += ds1722.o
-obj-$(CONFIG_DTT_DS1775) += ds1775.o
-obj-$(CONFIG_DTT_DS620) += ds620.o
-obj-$(CONFIG_DTT_LM63) += lm63.o
-obj-$(CONFIG_DTT_LM73) += lm73.o
-obj-$(CONFIG_DTT_LM75) += lm75.o
-obj-$(CONFIG_DTT_LM81) += lm81.o
diff --git a/drivers/hwmon/adm1021.c b/drivers/hwmon/adm1021.c
deleted file mode 100644
index 99e942b499..0000000000
--- a/drivers/hwmon/adm1021.c
+++ /dev/null
@@ -1,164 +0,0 @@
-/*
- * (C) Copyright 2003
- * Murray Jensen, CSIRO-MIT, Murray.Jensen at csiro.au
- *
- * based on dtt/lm75.c which is ...
- *
- * (C) Copyright 2001
- * Bill Hunter, Wave 7 Optics, williamhunter at mediaone.net
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * Analog Devices's ADM1021
- * "Low Cost Microprocessor System Temperature Monitor"
- */
-
-#include <common.h>
-
-#include <i2c.h>
-#include <dtt.h>
-
-#define DTT_READ_LOC_VALUE 0x00
-#define DTT_READ_REM_VALUE 0x01
-#define DTT_READ_STATUS 0x02
-#define DTT_READ_CONFIG 0x03
-#define DTT_READ_CONVRATE 0x04
-#define DTT_READ_LOC_HIGHLIM 0x05
-#define DTT_READ_LOC_LOWLIM 0x06
-#define DTT_READ_REM_HIGHLIM 0x07
-#define DTT_READ_REM_LOWLIM 0x08
-#define DTT_READ_DEVID 0xfe
-
-#define DTT_WRITE_CONFIG 0x09
-#define DTT_WRITE_CONVRATE 0x0a
-#define DTT_WRITE_LOC_HIGHLIM 0x0b
-#define DTT_WRITE_LOC_LOWLIM 0x0c
-#define DTT_WRITE_REM_HIGHLIM 0x0d
-#define DTT_WRITE_REM_LOWLIM 0x0e
-#define DTT_WRITE_ONESHOT 0x0f
-
-#define DTT_STATUS_BUSY 0x80 /* 1=ADC Converting */
-#define DTT_STATUS_LHIGH 0x40 /* 1=Local High Temp Limit Tripped */
-#define DTT_STATUS_LLOW 0x20 /* 1=Local Low Temp Limit Tripped */
-#define DTT_STATUS_RHIGH 0x10 /* 1=Remote High Temp Limit Tripped */
-#define DTT_STATUS_RLOW 0x08 /* 1=Remote Low Temp Limit Tripped */
-#define DTT_STATUS_OPEN 0x04 /* 1=Remote Sensor Open-Circuit */
-
-#define DTT_CONFIG_ALERT_MASKED 0x80 /* 0=ALERT Enabled, 1=ALERT Masked */
-#define DTT_CONFIG_STANDBY 0x40 /* 0=Run, 1=Standby */
-
-#define DTT_ADM1021_DEVID 0x41
-
-typedef
- struct {
- uint i2c_addr:7; /* 7bit i2c chip address */
- uint conv_rate:3; /* conversion rate */
- uint enable_alert:1; /* enable alert output pin */
- uint enable_local:1; /* enable internal temp sensor */
- uint max_local:8; /* internal temp maximum */
- uint min_local:8; /* internal temp minimum */
- uint enable_remote:1; /* enable remote temp sensor */
- uint max_remote:8; /* remote temp maximum */
- uint min_remote:8; /* remote temp minimum */
- }
-dtt_cfg_t;
-
-dtt_cfg_t dttcfg[] = CONFIG_SYS_DTT_ADM1021;
-
-int
-dtt_read (int sensor, int reg)
-{
- dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
- uchar data;
-
- if (i2c_read(dcp->i2c_addr, reg, 1, &data, 1) != 0)
- return -1;
-
- return (int)data;
-} /* dtt_read() */
-
-int
-dtt_write (int sensor, int reg, int val)
-{
- dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
- uchar data;
-
- data = (uchar)(val & 0xff);
-
- if (i2c_write(dcp->i2c_addr, reg, 1, &data, 1) != 0)
- return 1;
-
- return 0;
-} /* dtt_write() */
-
-int
-dtt_init_one(int sensor)
-{
- dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
- int reg, val;
-
- if (((sensor & 1) == 0 ? dcp->enable_local : dcp->enable_remote) == 0)
- return 1; /* sensor is disabled (or rather ignored) */
-
- /*
- * Setup High Limit register
- */
- if ((sensor & 1) == 0) {
- reg = DTT_WRITE_LOC_HIGHLIM;
- val = dcp->max_local;
- }
- else {
- reg = DTT_WRITE_REM_HIGHLIM;
- val = dcp->max_remote;
- }
- if (dtt_write (sensor, reg, val) != 0)
- return 1;
-
- /*
- * Setup Low Limit register
- */
- if ((sensor & 1) == 0) {
- reg = DTT_WRITE_LOC_LOWLIM;
- val = dcp->min_local;
- }
- else {
- reg = DTT_WRITE_REM_LOWLIM;
- val = dcp->min_remote;
- }
- if (dtt_write (sensor, reg, val) != 0)
- return 1;
-
- /* shouldn't hurt if the rest gets done twice */
-
- /*
- * Setup Conversion Rate register
- */
- if (dtt_write (sensor, DTT_WRITE_CONVRATE, dcp->conv_rate) != 0)
- return 1;
-
- /*
- * Setup configuraton register
- */
- val = 0; /* running */
- if (dcp->enable_alert == 0)
- val |= DTT_CONFIG_ALERT_MASKED; /* mask ALERT pin */
- if (dtt_write (sensor, DTT_WRITE_CONFIG, val) != 0)
- return 1;
-
- return 0;
-} /* dtt_init_one() */
-
-int
-dtt_get_temp (int sensor)
-{
- signed char val;
-
- if ((sensor & 1) == 0)
- val = dtt_read(sensor, DTT_READ_LOC_VALUE);
- else
- val = dtt_read(sensor, DTT_READ_REM_VALUE);
-
- return (int) val;
-} /* dtt_get_temp() */
diff --git a/drivers/hwmon/adt7460.c b/drivers/hwmon/adt7460.c
deleted file mode 100644
index 9b2c5b69ce..0000000000
--- a/drivers/hwmon/adt7460.c
+++ /dev/null
@@ -1,73 +0,0 @@
-/*
- * (C) Copyright 2008
- * Ricado Ribalda-Universidad Autonoma de Madrid, ricardo.ribalda at gmail.com
- * This work has been supported by: QTechnology http://qtec.com/
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <dtt.h>
-
-#define ADT7460_ADDRESS 0x2c
-#define ADT7460_INVALID 128
-#define ADT7460_CONFIG 0x40
-#define ADT7460_REM1_TEMP 0x25
-#define ADT7460_LOCAL_TEMP 0x26
-#define ADT7460_REM2_TEMP 0x27
-
-int dtt_read(int sensor, int reg)
-{
- u8 dir = reg;
- u8 data;
-
- if (i2c_read(ADT7460_ADDRESS, dir, 1, &data, 1) == -1)
- return -1;
- if (data == ADT7460_INVALID)
- return -1;
-
- return data;
-}
-
-int dtt_write(int sensor, int reg, int val)
-{
- u8 dir = reg;
- u8 data = val;
-
- if (i2c_write(ADT7460_ADDRESS, dir, 1, &data, 1) == -1)
- return -1;
-
- return 0;
-}
-
-int dtt_init_one(int sensor)
-{
- printf("ADT7460 at I2C address 0x%2x\n", ADT7460_ADDRESS);
-
- if (dtt_write(0, ADT7460_CONFIG, 1) == -1) {
- puts("Error initialiting ADT7460\n");
- return -1;
- }
-
- return 0;
-}
-
-int dtt_get_temp(int sensor)
-{
- int aux;
- u8 table[] =
- { ADT7460_REM1_TEMP, ADT7460_LOCAL_TEMP, ADT7460_REM2_TEMP };
-
- if (sensor > 2) {
- puts("DTT sensor does not exist\n");
- return -1;
- }
-
- aux = dtt_read(0, table[sensor]);
- if (aux == -1) {
- puts("DTT temperature read failed\n");
- return -1;
- }
-
- return aux;
-}
diff --git a/drivers/hwmon/ds1621.c b/drivers/hwmon/ds1621.c
deleted file mode 100644
index 66947a664e..0000000000
--- a/drivers/hwmon/ds1621.c
+++ /dev/null
@@ -1,155 +0,0 @@
-/*
- * (C) Copyright 2001
- * Erik Theisen, Wave 7 Optics, etheisen at mindspring.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * Dallas Semiconductor's DS1621/1631 Digital Thermometer and Thermostat.
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <dtt.h>
-
-/*
- * Device code
- */
-#define DTT_I2C_DEV_CODE 0x48 /* Dallas Semi's DS1621 */
-#define DTT_READ_TEMP 0xAA
-#define DTT_READ_COUNTER 0xA8
-#define DTT_READ_SLOPE 0xA9
-#define DTT_WRITE_START_CONV 0xEE
-#define DTT_WRITE_STOP_CONV 0x22
-#define DTT_TEMP_HIGH 0xA1
-#define DTT_TEMP_LOW 0xA2
-#define DTT_CONFIG 0xAC
-
-/*
- * Config register bits
- */
-#define DTT_CONFIG_1SHOT 0x01
-#define DTT_CONFIG_POLARITY 0x02
-#define DTT_CONFIG_R0 0x04 /* ds1631 only */
-#define DTT_CONFIG_R1 0x08 /* ds1631 only */
-#define DTT_CONFIG_NVB 0x10
-#define DTT_CONFIG_TLF 0x20
-#define DTT_CONFIG_THF 0x40
-#define DTT_CONFIG_DONE 0x80
-
-
-int dtt_read(int sensor, int reg)
-{
- int dlen;
- uchar data[2];
-
- /* Calculate sensor address and command */
- sensor = DTT_I2C_DEV_CODE + (sensor & 0x07); /* Calculate addr of ds1621*/
-
- /* Prepare to handle 2 byte result */
- switch(reg) {
- case DTT_READ_TEMP:
- case DTT_TEMP_HIGH:
- case DTT_TEMP_LOW:
- dlen = 2;
- break;
- default:
- dlen = 1;
- }
-
- /* Now try to read the register */
- if (i2c_read(sensor, reg, 1, data, dlen) != 0)
- return 1;
-
- /* Handle 2 byte result */
- if (dlen == 2)
- return (short)((data[0] << 8) | data[1]);
-
- return (int)data[0];
-}
-
-
-int dtt_write(int sensor, int reg, int val)
-{
- int dlen;
- uchar data[2];
-
- /* Calculate sensor address and register */
- sensor = DTT_I2C_DEV_CODE + (sensor & 0x07);
-
- /* Handle various data sizes. */
- switch(reg) {
- case DTT_READ_TEMP:
- case DTT_TEMP_HIGH:
- case DTT_TEMP_LOW:
- dlen = 2;
- data[0] = (char)((val >> 8) & 0xff); /* MSB first */
- data[1] = (char)(val & 0xff);
- break;
- case DTT_WRITE_START_CONV:
- case DTT_WRITE_STOP_CONV:
- dlen = 0;
- data[0] = (char)0;
- data[1] = (char)0;
- break;
- default:
- dlen = 1;
- data[0] = (char)(val & 0xff);
- }
-
- /* Write value to device */
- if (i2c_write(sensor, reg, 1, data, dlen) != 0)
- return 1;
-
- /* Poll NV memory busy bit in case write was to register stored in EEPROM */
- while(i2c_reg_read(sensor, DTT_CONFIG) & DTT_CONFIG_NVB)
- ;
-
- return 0;
-}
-
-
-int dtt_init_one(int sensor)
-{
- int val;
-
- /* Setup High Temp */
- val = ((CONFIG_SYS_DTT_MAX_TEMP * 2) << 7) & 0xff80;
- if (dtt_write(sensor, DTT_TEMP_HIGH, val) != 0)
- return 1;
-
- /* Setup Low Temp - hysteresis */
- val = (((CONFIG_SYS_DTT_MAX_TEMP - CONFIG_SYS_DTT_HYSTERESIS) * 2) << 7) & 0xff80;
- if (dtt_write(sensor, DTT_TEMP_LOW, val) != 0)
- return 1;
-
- /*
- * Setup configuraton register
- *
- * Clear THF & TLF, Reserved = 1, Polarity = Active Low, One Shot = YES
- *
- * We run in polled mode, since there isn't any way to know if this
- * lousy device is ready to provide temperature readings on power up.
- */
- val = 0x9;
- if (dtt_write(sensor, DTT_CONFIG, val) != 0)
- return 1;
-
- return 0;
-}
-
-int dtt_get_temp(int sensor)
-{
- int i;
-
- /* Start a conversion, may take up to 1 second. */
- dtt_write(sensor, DTT_WRITE_START_CONV, 0);
- for (i = 0; i <= 10; i++) {
- udelay(100000);
- if (dtt_read(sensor, DTT_CONFIG) & DTT_CONFIG_DONE)
- break;
- }
-
- return (dtt_read(sensor, DTT_READ_TEMP) / 256);
-}
diff --git a/drivers/hwmon/ds1722.c b/drivers/hwmon/ds1722.c
deleted file mode 100644
index c46958846c..0000000000
--- a/drivers/hwmon/ds1722.c
+++ /dev/null
@@ -1,137 +0,0 @@
-#include <common.h>
-#include <asm/ic/ssi.h>
-#include <ds1722.h>
-
-static void ds1722_select(int dev)
-{
- ssi_set_interface(4096, 0, 0, 0);
- ssi_chip_select(0);
- udelay(1);
- ssi_chip_select(dev);
- udelay(1);
-}
-
-
-u8 ds1722_read(int dev, int addr)
-{
- u8 res;
-
- ds1722_select(dev);
-
- ssi_tx_byte(addr);
- res = ssi_rx_byte();
-
- ssi_chip_select(0);
-
- return res;
-}
-
-void ds1722_write(int dev, int addr, u8 data)
-{
- ds1722_select(dev);
-
- ssi_tx_byte(0x80|addr);
- ssi_tx_byte(data);
-
- ssi_chip_select(0);
-}
-
-
-u16 ds1722_temp(int dev, int resolution)
-{
- static int useconds[] = {
- 75000, 150000, 300000, 600000, 1200000
- };
- char temp;
- u16 res;
-
-
- /* set up the desired resulotion ... */
- ds1722_write(dev, 0, 0xe0 | (resolution << 1));
-
- /* wait while the chip measures the tremperature */
- udelay(useconds[resolution]);
-
- res = (temp = ds1722_read(dev, 2)) << 8;
-
- if (temp < 0) {
- temp = (16 - (ds1722_read(dev, 1) >> 4)) & 0x0f;
- } else {
- temp = (ds1722_read(dev, 1) >> 4);
- }
-
- switch (temp) {
- case 0:
- /* .0000 */
- break;
- case 1:
- /* .0625 */
- res |=1;
- break;
- case 2:
- /* .1250 */
- res |=1;
- break;
- case 3:
- /* .1875 */
- res |=2;
- break;
- case 4:
- /* .2500 */
- res |=3;
- break;
- case 5:
- /* .3125 */
- res |=3;
- break;
- case 6:
- /* .3750 */
- res |=4;
- break;
- case 7:
- /* .4375 */
- res |=4;
- break;
- case 8:
- /* .5000 */
- res |=5;
- break;
- case 9:
- /* .5625 */
- res |=6;
- break;
- case 10:
- /* .6250 */
- res |=6;
- break;
- case 11:
- /* .6875 */
- res |=7;
- break;
- case 12:
- /* .7500 */
- res |=8;
- break;
- case 13:
- /* .8125 */
- res |=8;
- break;
- case 14:
- /* .8750 */
- res |=9;
- break;
- case 15:
- /* .9375 */
- res |=9;
- break;
- }
- return res;
-
-}
-
-int ds1722_probe(int dev)
-{
- u16 temp = ds1722_temp(dev, DS1722_RESOLUTION_12BIT);
- printf("%d.%d deg C\n\n", (char)(temp >> 8), temp & 0xff);
- return 0;
-}
diff --git a/drivers/hwmon/ds1775.c b/drivers/hwmon/ds1775.c
deleted file mode 100644
index 4c0c0b82a0..0000000000
--- a/drivers/hwmon/ds1775.c
+++ /dev/null
@@ -1,126 +0,0 @@
-/*
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * Dallas Semiconductor's DS1775 Digital Thermometer and Thermostat
- */
-
-#include <common.h>
-
-#include <i2c.h>
-#include <dtt.h>
-
-#define DTT_I2C_DEV_CODE 0x48 /* Dallas Semi's DS1775 device code */
-#define DTT_READ_TEMP 0x0
-#define DTT_CONFIG 0x1
-#define DTT_TEMP_HYST 0x2
-#define DTT_TEMP_OS 0x3
-
-int dtt_read(int sensor, int reg)
-{
- int dlen;
- uchar data[2];
-
- /*
- * Calculate sensor address and command
- */
- sensor = DTT_I2C_DEV_CODE + (sensor & 0x07); /* Calculate addr of ds1775 */
-
- /*
- * Prepare to handle 2 byte result
- */
- if ((reg == DTT_READ_TEMP) ||
- (reg == DTT_TEMP_OS) || (reg == DTT_TEMP_HYST))
- dlen = 2;
- else
- dlen = 1;
-
- /*
- * Now try to read the register
- */
- if (i2c_read(sensor, reg, 1, data, dlen) != 0)
- return 1;
-
- /*
- * Handle 2 byte result
- */
- if (dlen == 2)
- return ((int)((short)data[1] + (((short)data[0]) << 8)));
-
- return (int) data[0];
-}
-
-
-int dtt_write(int sensor, int reg, int val)
-{
- int dlen;
- uchar data[2];
-
- /*
- * Calculate sensor address and register
- */
- sensor = DTT_I2C_DEV_CODE + (sensor & 0x07);
-
- /*
- * Handle various data sizes
- */
- if ((reg == DTT_READ_TEMP) ||
- (reg == DTT_TEMP_OS) || (reg == DTT_TEMP_HYST)) {
- dlen = 2;
- data[0] = (char)((val >> 8) & 0xff); /* MSB first */
- data[1] = (char)(val & 0xff);
- } else {
- dlen = 1;
- data[0] = (char)(val & 0xff);
- }
-
- /*
- * Write value to device
- */
- if (i2c_write(sensor, reg, 1, data, dlen) != 0)
- return 1;
-
- return 0;
-}
-
-
-int dtt_init_one(int sensor)
-{
- int val;
-
- /*
- * Setup High Temp
- */
- val = ((CONFIG_SYS_DTT_MAX_TEMP * 2) << 7) & 0xff80;
- if (dtt_write(sensor, DTT_TEMP_OS, val) != 0)
- return 1;
- udelay(50000); /* Max 50ms */
-
- /*
- * Setup Low Temp - hysteresis
- */
- val = (((CONFIG_SYS_DTT_MAX_TEMP - CONFIG_SYS_DTT_HYSTERESIS) * 2) << 7) & 0xff80;
- if (dtt_write(sensor, DTT_TEMP_HYST, val) != 0)
- return 1;
- udelay(50000); /* Max 50ms */
-
- /*
- * Setup configuraton register
- *
- * Fault Tolerance limits 4, Thermometer resolution bits is 9,
- * Polarity = Active Low,continuous conversion mode, Thermostat
- * mode is interrupt mode
- */
- val = 0xa;
- if (dtt_write(sensor, DTT_CONFIG, val) != 0)
- return 1;
- udelay(50000); /* Max 50ms */
-
- return 0;
-}
-
-int dtt_get_temp(int sensor)
-{
- return (dtt_read(sensor, DTT_READ_TEMP) / 256);
-}
diff --git a/drivers/hwmon/ds620.c b/drivers/hwmon/ds620.c
deleted file mode 100644
index 1ecc3da799..0000000000
--- a/drivers/hwmon/ds620.c
+++ /dev/null
@@ -1,65 +0,0 @@
-/*
- * DS620 DTT support
- *
- * (C) Copyright 2014 3ADEV <http://www.3adev.com>
- * Written-by: Albert ARIBAUD <albert.aribaud at 3adev.fr>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * Dallas Semiconductor's DS1621/1631 Digital Thermometer and Thermostat.
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <dtt.h>
-
-/*
- * Device code
- */
-#define DTT_I2C_DEV_CODE 0x48
-#define DTT_START_CONVERT 0x51
-#define DTT_TEMP 0xAA
-#define DTT_CONFIG 0xAC
-
-/*
- * Config register MSB bits
- */
-#define DTT_CONFIG_1SHOT 0x01
-#define DTT_CONFIG_AUTOC 0x02
-#define DTT_CONFIG_R0 0x04 /* always 1 */
-#define DTT_CONFIG_R1 0x08 /* always 1 */
-#define DTT_CONFIG_TLF 0x10
-#define DTT_CONFIG_THF 0x20
-#define DTT_CONFIG_NVB 0x40
-#define DTT_CONFIG_DONE 0x80
-
-#define CHIP(sensor) (DTT_I2C_DEV_CODE + (sensor & 0x07))
-
-int dtt_init_one(int sensor)
-{
- uint8_t config = DTT_CONFIG_1SHOT
- | DTT_CONFIG_R0
- | DTT_CONFIG_R1;
- return i2c_write(CHIP(sensor), DTT_CONFIG, 1, &config, 1);
-}
-
-int dtt_get_temp(int sensor)
-{
- uint8_t status;
- uint8_t temp[2];
-
- /* Start a conversion, may take up to 1 second. */
- i2c_write(CHIP(sensor), DTT_START_CONVERT, 1, NULL, 0);
- do {
- if (i2c_read(CHIP(sensor), DTT_CONFIG, 1, &status, 1))
- /* bail out if I2C error */
- status |= DTT_CONFIG_DONE;
- } while (!(status & DTT_CONFIG_DONE));
- if (i2c_read(CHIP(sensor), DTT_TEMP, 1, temp, 2))
- /* bail out if I2C error */
- return -274; /* below absolute zero == error */
-
- return ((int16_t)(temp[1] | (temp[0] << 8))) >> 7;
-}
diff --git a/drivers/hwmon/lm63.c b/drivers/hwmon/lm63.c
deleted file mode 100644
index 053c785fc5..0000000000
--- a/drivers/hwmon/lm63.c
+++ /dev/null
@@ -1,160 +0,0 @@
-/*
- * (C) Copyright 2007-2008
- * Dirk Eibach, Guntermann & Drunck GmbH, eibach at gdsys.de
- * based on lm75.c by Bill Hunter
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * National LM63/LM64 Temperature Sensor
- * Main difference: LM 64 has -16 Kelvin temperature offset
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <dtt.h>
-
-#define DTT_I2C_LM63_ADDR 0x4C /* National LM63 device */
-
-#define DTT_READ_TEMP_RMT_MSB 0x01
-#define DTT_CONFIG 0x03
-#define DTT_READ_TEMP_RMT_LSB 0x10
-#define DTT_TACHLIM_LSB 0x48
-#define DTT_TACHLIM_MSB 0x49
-#define DTT_FAN_CONFIG 0x4A
-#define DTT_PWM_FREQ 0x4D
-#define DTT_PWM_LOOKUP_BASE 0x50
-
-struct pwm_lookup_entry {
- u8 temp;
- u8 pwm;
-};
-
-/*
- * Device code
- */
-
-int dtt_read(int sensor, int reg)
-{
- int dlen;
- uchar data[2];
-
- /*
- * Calculate sensor address and register.
- */
- if (!sensor)
- sensor = DTT_I2C_LM63_ADDR; /* legacy config */
-
- dlen = 1;
-
- /*
- * Now try to read the register.
- */
- if (i2c_read(sensor, reg, 1, data, dlen) != 0)
- return -1;
-
- return (int)data[0];
-} /* dtt_read() */
-
-int dtt_write(int sensor, int reg, int val)
-{
- int dlen;
- uchar data[2];
-
- /*
- * Calculate sensor address and register.
- */
- if (!sensor)
- sensor = DTT_I2C_LM63_ADDR; /* legacy config */
-
- dlen = 1;
- data[0] = (char)(val & 0xff);
-
- /*
- * Write value to register.
- */
- if (i2c_write(sensor, reg, 1, data, dlen) != 0)
- return 1;
-
- return 0;
-} /* dtt_write() */
-
-static int is_lm64(int sensor)
-{
- return sensor && (sensor != DTT_I2C_LM63_ADDR);
-}
-
-int dtt_init_one(int sensor)
-{
- int i;
- int val;
-
- struct pwm_lookup_entry pwm_lookup[] = CONFIG_DTT_PWM_LOOKUPTABLE;
-
- /*
- * Set PWM Frequency to 2.5% resolution
- */
- val = 20;
- if (dtt_write(sensor, DTT_PWM_FREQ, val) != 0)
- return 1;
-
- /*
- * Set Tachometer Limit
- */
- val = CONFIG_DTT_TACH_LIMIT;
- if (dtt_write(sensor, DTT_TACHLIM_LSB, val & 0xff) != 0)
- return 1;
- if (dtt_write(sensor, DTT_TACHLIM_MSB, (val >> 8) & 0xff) != 0)
- return 1;
-
- /*
- * Make sure PWM Lookup-Table is writeable
- */
- if (dtt_write(sensor, DTT_FAN_CONFIG, 0x20) != 0)
- return 1;
-
- /*
- * Setup PWM Lookup-Table
- */
- for (i = 0; i < ARRAY_SIZE(pwm_lookup); i++) {
- int address = DTT_PWM_LOOKUP_BASE + 2 * i;
- val = pwm_lookup[i].temp;
- if (is_lm64(sensor))
- val -= 16;
- if (dtt_write(sensor, address, val) != 0)
- return 1;
- val = dtt_read(sensor, address);
- val = pwm_lookup[i].pwm;
- if (dtt_write(sensor, address + 1, val) != 0)
- return 1;
- }
-
- /*
- * Enable PWM Lookup-Table, PWM Clock 360 kHz, Tachometer Mode 2
- */
- val = 0x02;
- if (dtt_write(sensor, DTT_FAN_CONFIG, val) != 0)
- return 1;
-
- /*
- * Enable Tach input
- */
- val = dtt_read(sensor, DTT_CONFIG) | 0x04;
- if (dtt_write(sensor, DTT_CONFIG, val) != 0)
- return 1;
-
- return 0;
-}
-
-int dtt_get_temp(int sensor)
-{
- s16 temp = (dtt_read(sensor, DTT_READ_TEMP_RMT_MSB) << 8)
- | (dtt_read(sensor, DTT_READ_TEMP_RMT_LSB));
-
- if (is_lm64(sensor))
- temp += 16 << 8;
-
- /* Ignore LSB for now, U-Boot only prints natural numbers */
- return temp >> 8;
-}
diff --git a/drivers/hwmon/lm73.c b/drivers/hwmon/lm73.c
deleted file mode 100644
index c15c7514d8..0000000000
--- a/drivers/hwmon/lm73.c
+++ /dev/null
@@ -1,146 +0,0 @@
-/*
- * (C) Copyright 2007-2008
- * Larry Johnson, lrj at acm.org
- *
- * based on dtt/lm75.c which is ...
- *
- * (C) Copyright 2001
- * Bill Hunter, Wave 7 Optics, williamhunter at mediaone.net
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * National Semiconductor LM73 Temperature Sensor
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <dtt.h>
-
-/*
- * Device code
- */
-#define DTT_I2C_DEV_CODE 0x48 /* National Semi's LM73 device */
-#define DTT_READ_TEMP 0x0
-#define DTT_CONFIG 0x1
-#define DTT_TEMP_HIGH 0x2
-#define DTT_TEMP_LOW 0x3
-#define DTT_CONTROL 0x4
-#define DTT_ID 0x7
-
-int dtt_read(int const sensor, int const reg)
-{
- int dlen;
- uint8_t data[2];
-
- /*
- * Validate 'reg' param and get register size.
- */
- switch (reg) {
- case DTT_CONFIG:
- case DTT_CONTROL:
- dlen = 1;
- break;
- case DTT_READ_TEMP:
- case DTT_TEMP_HIGH:
- case DTT_TEMP_LOW:
- case DTT_ID:
- dlen = 2;
- break;
- default:
- return -1;
- }
- /*
- * Try to read the register at the calculated sensor address.
- */
- if (0 !=
- i2c_read(DTT_I2C_DEV_CODE + (sensor & 0x07), reg, 1, data, dlen))
- return -1;
- /*
- * Handle 2 byte result.
- */
- if (2 == dlen)
- return (int)((unsigned)data[0] << 8 | (unsigned)data[1]);
-
- return (int)data[0];
-} /* dtt_read() */
-
-int dtt_write(int const sensor, int const reg, int const val)
-{
- int dlen;
- uint8_t data[2];
-
- /*
- * Validate 'reg' param and handle register size
- */
- switch (reg) {
- case DTT_CONFIG:
- case DTT_CONTROL:
- dlen = 1;
- data[0] = (uint8_t) val;
- break;
- case DTT_TEMP_HIGH:
- case DTT_TEMP_LOW:
- dlen = 2;
- data[0] = (uint8_t) (val >> 8); /* MSB first */
- data[1] = (uint8_t) val;
- break;
- default:
- return -1;
- }
- /*
- * Write value to register at the calculated sensor address.
- */
- return 0 != i2c_write(DTT_I2C_DEV_CODE + (sensor & 0x07), reg, 1, data,
- dlen);
-} /* dtt_write() */
-
-int dtt_init_one(int const sensor)
-{
- int val;
-
- /*
- * Validate the Identification register
- */
- if (0x0190 != dtt_read(sensor, DTT_ID))
- return -1;
- /*
- * Setup THIGH (upper-limit) and TLOW (lower-limit) registers
- */
- val = CONFIG_SYS_DTT_MAX_TEMP << 7;
- if (dtt_write(sensor, DTT_TEMP_HIGH, val))
- return -1;
-
- val = CONFIG_SYS_DTT_MIN_TEMP << 7;
- if (dtt_write(sensor, DTT_TEMP_LOW, val))
- return -1;
- /*
- * Setup configuraton register
- */
- /* config = alert active low, disabled, and reset */
- val = 0x64;
- if (dtt_write(sensor, DTT_CONFIG, val))
- return -1;
- /*
- * Setup control/status register
- */
- /* control = temp resolution 0.25C */
- val = 0x00;
- if (dtt_write(sensor, DTT_CONTROL, val))
- return -1;
-
- dtt_read(sensor, DTT_CONTROL); /* clear temperature flags */
- return 0;
-} /* dtt_init_one() */
-
-int dtt_get_temp(int const sensor)
-{
- int const ret = dtt_read(sensor, DTT_READ_TEMP);
-
- if (ret < 0) {
- printf("DTT temperature read failed.\n");
- return 0;
- }
- return (int)((int16_t) ret + 0x0040) >> 7;
-} /* dtt_get_temp() */
diff --git a/drivers/hwmon/lm75.c b/drivers/hwmon/lm75.c
deleted file mode 100644
index aafa4757b1..0000000000
--- a/drivers/hwmon/lm75.c
+++ /dev/null
@@ -1,139 +0,0 @@
-/*
- * (C) Copyright 2001
- * Bill Hunter, Wave 7 Optics, williamhunter at mediaone.net
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * On Semiconductor's LM75 Temperature Sensor
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <dtt.h>
-
-/*
- * Device code
- */
-#define DTT_I2C_DEV_CODE 0x48 /* ON Semi's LM75 device */
-#define DTT_READ_TEMP 0x0
-#define DTT_CONFIG 0x1
-#define DTT_TEMP_HYST 0x2
-#define DTT_TEMP_SET 0x3
-
-int dtt_read(int sensor, int reg)
-{
- int dlen;
- uchar data[2];
-
-#ifdef CONFIG_DTT_AD7414
- /*
- * On AD7414 the first value upon bootup is not read correctly.
- * This is most likely because of the 800ms update time of the
- * temp register in normal update mode. To get current values
- * each time we issue the "dtt" command including upon powerup
- * we switch into one-short mode.
- *
- * Issue one-shot mode command
- */
- dtt_write(sensor, DTT_CONFIG, 0x64);
-#endif
-
- /* Validate 'reg' param */
- if((reg < 0) || (reg > 3))
- return -1;
-
- /* Calculate sensor address and register. */
- sensor = DTT_I2C_DEV_CODE + (sensor & 0x07);
-
- /* Prepare to handle 2 byte result. */
- if ((reg == DTT_READ_TEMP) ||
- (reg == DTT_TEMP_HYST) ||
- (reg == DTT_TEMP_SET))
- dlen = 2;
- else
- dlen = 1;
-
- /* Now try to read the register. */
- if (i2c_read(sensor, reg, 1, data, dlen) != 0)
- return -1;
-
- /* Handle 2 byte result. */
- if (dlen == 2)
- return ((int)((short)data[1] + (((short)data[0]) << 8)));
-
- return (int)data[0];
-} /* dtt_read() */
-
-
-int dtt_write(int sensor, int reg, int val)
-{
- int dlen;
- uchar data[2];
-
- /* Validate 'reg' param */
- if ((reg < 0) || (reg > 3))
- return 1;
-
- /* Calculate sensor address and register. */
- sensor = DTT_I2C_DEV_CODE + (sensor & 0x07);
-
- /* Handle 2 byte values. */
- if ((reg == DTT_READ_TEMP) ||
- (reg == DTT_TEMP_HYST) ||
- (reg == DTT_TEMP_SET)) {
- dlen = 2;
- data[0] = (char)((val >> 8) & 0xff); /* MSB first */
- data[1] = (char)(val & 0xff);
- } else {
- dlen = 1;
- data[0] = (char)(val & 0xff);
- }
-
- /* Write value to register. */
- if (i2c_write(sensor, reg, 1, data, dlen) != 0)
- return 1;
-
- return 0;
-} /* dtt_write() */
-
-
-int dtt_init_one(int sensor)
-{
- int val;
-
- /* Setup TSET ( trip point ) register */
- val = ((CONFIG_SYS_DTT_MAX_TEMP * 2) << 7) & 0xff80; /* trip */
- if (dtt_write(sensor, DTT_TEMP_SET, val) != 0)
- return 1;
-
- /* Setup THYST ( untrip point ) register - Hysteresis */
- val = (((CONFIG_SYS_DTT_MAX_TEMP - CONFIG_SYS_DTT_HYSTERESIS) * 2) << 7) & 0xff80;
- if (dtt_write(sensor, DTT_TEMP_HYST, val) != 0)
- return 1;
-
- /* Setup configuraton register */
-#ifdef CONFIG_DTT_AD7414
- /* config = alert active low and disabled */
- val = 0x60;
-#else
- /* config = 6 sample integration, int mode, active low, and enable */
- val = 0x18;
-#endif
- if (dtt_write(sensor, DTT_CONFIG, val) != 0)
- return 1;
-
- return 0;
-} /* dtt_init_one() */
-
-int dtt_get_temp(int sensor)
-{
- int const ret = dtt_read(sensor, DTT_READ_TEMP);
-
- if (ret < 0) {
- printf("DTT temperature read failed.\n");
- return 0;
- }
- return (int)((int16_t) ret / 256);
-} /* dtt_get_temp() */
diff --git a/drivers/hwmon/lm81.c b/drivers/hwmon/lm81.c
deleted file mode 100644
index bcc8d3293b..0000000000
--- a/drivers/hwmon/lm81.c
+++ /dev/null
@@ -1,111 +0,0 @@
-/*
- * (C) Copyright 2006
- * Heiko Schocher, DENX Software Enginnering <hs at denx.de>
- *
- * based on dtt/lm75.c which is ...
- *
- * (C) Copyright 2001
- * Bill Hunter, Wave 7 Optics, williamhunter at mediaone.net
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * On Semiconductor's LM81 Temperature Sensor
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <dtt.h>
-
-/*
- * Device code
- */
-#define DTT_I2C_DEV_CODE 0x2c /* ON Semi's LM81 device */
-#define DTT_READ_TEMP 0x27
-#define DTT_CONFIG_TEMP 0x4b
-#define DTT_TEMP_MAX 0x39
-#define DTT_TEMP_HYST 0x3a
-#define DTT_CONFIG 0x40
-
-int dtt_read(int sensor, int reg)
-{
- int dlen = 1;
- uchar data[2];
-
- /*
- * Calculate sensor address and register.
- */
- sensor = DTT_I2C_DEV_CODE + (sensor & 0x03); /* calculate address of lm81 */
-
- /*
- * Now try to read the register.
- */
- if (i2c_read(sensor, reg, 1, data, dlen) != 0)
- return -1;
-
- return (int)data[0];
-} /* dtt_read() */
-
-
-int dtt_write(int sensor, int reg, int val)
-{
- uchar data;
-
- /*
- * Calculate sensor address and register.
- */
- sensor = DTT_I2C_DEV_CODE + (sensor & 0x03); /* calculate address of lm81 */
-
- data = (char)(val & 0xff);
-
- /*
- * Write value to register.
- */
- if (i2c_write(sensor, reg, 1, &data, 1) != 0)
- return 1;
-
- return 0;
-} /* dtt_write() */
-
-#define DTT_MANU 0x3e
-#define DTT_REV 0x3f
-#define DTT_CONFIG 0x40
-#define DTT_ADR 0x48
-
-int dtt_init_one(int sensor)
-{
- int man;
- int adr;
- int rev;
-
- if (dtt_write (sensor, DTT_CONFIG, 0x01) < 0)
- return 1;
- /* The LM81 needs 400ms to get the correct values ... */
- udelay (400000);
- man = dtt_read (sensor, DTT_MANU);
- if (man != 0x01)
- return 1;
- adr = dtt_read (sensor, DTT_ADR);
- if (adr < 0)
- return 1;
- rev = dtt_read (sensor, DTT_REV);
- if (rev < 0)
- return 1;
-
- debug ("DTT: Found LM81@%x Rev: %d\n", adr, rev);
- return 0;
-} /* dtt_init_one() */
-
-
-#define TEMP_FROM_REG(temp) \
- ((temp)<256?((((temp)&0x1fe) >> 1) * 10) + ((temp) & 1) * 5: \
- ((((temp)&0x1fe) >> 1) -255) * 10 - ((temp) & 1) * 5) \
-
-int dtt_get_temp(int sensor)
-{
- int val = dtt_read (sensor, DTT_READ_TEMP);
- int tmpcnf = dtt_read (sensor, DTT_CONFIG_TEMP);
-
- return (TEMP_FROM_REG((val << 1) + ((tmpcnf & 0x80) >> 7))) / 10;
-} /* dtt_get_temp() */
diff --git a/include/config_cmd_all.h b/include/config_cmd_all.h
index bc0bc2b6c8..95c05350cd 100644
--- a/include/config_cmd_all.h
+++ b/include/config_cmd_all.h
@@ -13,7 +13,6 @@
* Alphabetical list of all possible commands.
*/
-#define CONFIG_CMD_DTT /* Digital Therm and Thermostat */
#define CONFIG_CMD_EEPROM /* EEPROM read/write support */
#define CONFIG_CMD_FDC /* Floppy Disk Support */
#define CONFIG_CMD_FUSE /* Device fuse support */
diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h
index b9599b5e3b..8628b7ed18 100644
--- a/include/configs/PMC440.h
+++ b/include/configs/PMC440.h
@@ -163,26 +163,6 @@
#define CONFIG_SYS_EEPROM_WREN 1
#define CONFIG_SYS_I2C_BOOT_EEPROM_ADDR 0x52
-/*
- * standard dtt sensor configuration - bottom bit will determine local or
- * remote sensor of the TMP401
- */
-#define CONFIG_DTT_SENSORS { 0, 1 }
-
-/*
- * The PMC440 uses a TI TMP401 temperature sensor. This part
- * is basically compatible to the ADM1021 that is supported
- * by U-Boot.
- *
- * - i2c addr 0x4c
- * - conversion rate 0x02 = 0.25 conversions/second
- * - ALERT ouput disabled
- * - local temp sensor enabled, min set to 0 deg, max set to 70 deg
- * - remote temp sensor enabled, min set to 0 deg, max set to 70 deg
- */
-#define CONFIG_DTT_ADM1021
-#define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
-
#define CONFIG_PREBOOT "echo Add \\\"run fpga\\\" and " \
"\\\"painit\\\" to preboot command"
@@ -258,7 +238,6 @@
/* Partitions */
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCI
diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h
index e3c2cca3c3..df6386c602 100644
--- a/include/configs/TQM834x.h
+++ b/include/configs/TQM834x.h
@@ -184,13 +184,6 @@
#define CONFIG_RTC_DS1337 /* use ds1337 rtc via i2c */
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
-/* I2C SYSMON (LM75) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-
/*
* TSEC
*/
@@ -280,7 +273,6 @@
/*
* Command line configuration.
*/
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_REGINFO
diff --git a/include/configs/UCP1020.h b/include/configs/UCP1020.h
index cd46db4f6f..8265f3c1ab 100644
--- a/include/configs/UCP1020.h
+++ b/include/configs/UCP1020.h
@@ -129,27 +129,6 @@
#define CONFIG_HWCONFIG
-#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */
-#define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */
-#define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */
-/*
- * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details).
- * there will be one entry in this array for each two (dummy) sensors in
- * CONFIG_DTT_SENSORS.
- *
- * For uCP1020 module:
- * - only one ADM1021/NCT72
- * - i2c addr 0x41
- * - conversion rate 0x02 = 0.25 conversions/second
- * - ALERT output disabled
- * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
- * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
- */
-#define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \
- 0x02, 0, 1, 0, 85, 1, 0, 85} }
-
-#define CONFIG_CMD_DTT
-
/*
* These can be toggled for performance analysis, otherwise use default.
*/
diff --git a/include/configs/acadia.h b/include/configs/acadia.h
index 9f35e71d0c..0be310d4a3 100644
--- a/include/configs/acadia.h
+++ b/include/configs/acadia.h
@@ -124,14 +124,6 @@
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_AD7414 1 /* use AD7414 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-
/*-----------------------------------------------------------------------
* Ethernet
*----------------------------------------------------------------------*/
@@ -160,7 +152,6 @@
/*
* Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_NAND
/*-----------------------------------------------------------------------
diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h
index ea440d6e16..b495d0645b 100644
--- a/include/configs/canyonlands.h
+++ b/include/configs/canyonlands.h
@@ -261,14 +261,6 @@
#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
#define CONFIG_4xx_CONFIG_BLOCKSIZE 16
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 /* ON Semi's LM75 */
-#define CONFIG_DTT_AD7414 /* use AD7414 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-
#if !defined(CONFIG_ARCHES)
/* RTC configuration */
#define CONFIG_RTC_M41T62
@@ -369,17 +361,14 @@
* Commands additional to the ones defined in amcc-common.h
*/
#if defined(CONFIG_ARCHES)
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SDRAM
#elif defined(CONFIG_CANYONLANDS)
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SATA
#define CONFIG_CMD_SDRAM
#elif defined(CONFIG_GLACIER)
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SDRAM
diff --git a/include/configs/dlvision-10g.h b/include/configs/dlvision-10g.h
index e32651f541..89f24e0980 100644
--- a/include/configs/dlvision-10g.h
+++ b/include/configs/dlvision-10g.h
@@ -57,7 +57,6 @@
/*
* Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_CMD_DTT
#undef CONFIG_CMD_EEPROM
#undef CONFIG_CMD_IRQ
@@ -111,13 +110,6 @@
#define CONFIG_SYS_SPD_BUS_NUM 4
/* Temp sensor/hwmon/dtt */
-#define CONFIG_SYS_DTT_BUS_NUM 4
-#define CONFIG_DTT_LM63 1 /* National LM63 */
-#define CONFIG_DTT_SENSORS { 0x4c, 0x4e, 0x18 } /* Sensor addresses */
-#define CONFIG_DTT_PWM_LOOKUPTABLE \
- { { 46, 10 }, { 48, 14 }, { 50, 19 }, { 52, 23 },\
- { 54, 27 }, { 56, 31 }, { 58, 36 }, { 60, 40 } }
-#define CONFIG_DTT_TACH_LIMIT 0xa10
#define CONFIG_SYS_ICS8N3QV01_I2C {1, 3}
#define CONFIG_SYS_SIL1178_I2C {0, 2}
diff --git a/include/configs/dlvision.h b/include/configs/dlvision.h
index 2b7d62b034..ec21a8347a 100644
--- a/include/configs/dlvision.h
+++ b/include/configs/dlvision.h
@@ -55,7 +55,6 @@
/*
* Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_CMD_DTT
#undef CONFIG_CMD_EEPROM
#undef CONFIG_CMD_IRQ
diff --git a/include/configs/exynos5-common.h b/include/configs/exynos5-common.h
index 5411e5ff49..91976a75bc 100644
--- a/include/configs/exynos5-common.h
+++ b/include/configs/exynos5-common.h
@@ -46,8 +46,6 @@
/* Thermal Management Unit */
#define CONFIG_EXYNOS_TMU
-#define CONFIG_CMD_DTT
-#define CONFIG_TMU_CMD_DTT
/* MMC SPL */
#define COPY_BL2_FNPTR_ADDR 0x02020030
diff --git a/include/configs/intip.h b/include/configs/intip.h
index f1f840923b..036fd20eb4 100644
--- a/include/configs/intip.h
+++ b/include/configs/intip.h
@@ -218,13 +218,6 @@
#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
#define CONFIG_4xx_CONFIG_BLOCKSIZE 16
-/* I2C SYSMON */
-#define CONFIG_DTT_LM63 1 /* National LM63 */
-#define CONFIG_DTT_SENSORS { 0 } /* Sensor addresses */
-#define CONFIG_DTT_PWM_LOOKUPTABLE \
- { { 40, 10 }, { 50, 20 }, { 60, 40 } }
-#define CONFIG_DTT_TACH_LIMIT 0xa10
-
/* RTC configuration */
#define CONFIG_RTC_DS1337 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
@@ -272,7 +265,6 @@
/*
* Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SDRAM
diff --git a/include/configs/io.h b/include/configs/io.h
index 3e44a8c607..dd195ffeed 100644
--- a/include/configs/io.h
+++ b/include/configs/io.h
@@ -57,7 +57,6 @@
/*
* Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_CMD_DTT
#undef CONFIG_CMD_EEPROM
#undef CONFIG_CMD_IRQ
@@ -93,11 +92,6 @@
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
/* Temp sensor/hwmon/dtt */
-#define CONFIG_DTT_LM63 1 /* National LM63 */
-#define CONFIG_DTT_SENSORS { 0 } /* Sensor addresses */
-#define CONFIG_DTT_PWM_LOOKUPTABLE \
- { { 40, 10 }, { 50, 20 }, { 60, 40 } }
-#define CONFIG_DTT_TACH_LIMIT 0xa10
/*
* FLASH organization
diff --git a/include/configs/io64.h b/include/configs/io64.h
index 8e754fc10b..1b58f04540 100644
--- a/include/configs/io64.h
+++ b/include/configs/io64.h
@@ -327,14 +327,6 @@
#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
#define CONFIG_4xx_CONFIG_BLOCKSIZE 16
-/* Temp sensor/hwmon/dtt */
-#define CONFIG_DTT_LM63 1 /* National LM63 */
-#define CONFIG_DTT_SENSORS { 0x18, 0x4c, 0x4e } /* Sensor addresses */
-#define CONFIG_DTT_PWM_LOOKUPTABLE \
- { { 40, 10 }, { 43, 13 }, { 46, 16 }, \
- { 50, 20 }, { 53, 27 }, { 56, 34 }, { 60, 40 } }
-#define CONFIG_DTT_TACH_LIMIT 0xa10
-
/*-----------------------------------------------------------------------
* Ethernet
*----------------------------------------------------------------------*/
@@ -373,7 +365,6 @@
/*
* Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_CMD_DTT
#define CONFIG_SYS_POST_MEMORY_ON CONFIG_SYS_POST_MEMORY
diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index 3143b631ce..c3b9da0d96 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -123,31 +123,6 @@
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with linux */
-/* I2C DTT */
-#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */
-#define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */
-/*
- * standard dtt sensor configuration - bottom bit will determine local or
- * remote sensor of the ADM1021, the rest determines index into
- * CONFIG_SYS_DTT_ADM1021 array below.
- */
-#define CONFIG_DTT_SENSORS { 0, 1 }
-
-/*
- * ADM1021 temp sensor configuration (see dtt/adm1021.c for details).
- * there will be one entry in this array for each two (dummy) sensors in
- * CONFIG_DTT_SENSORS.
- *
- * For Katmai board:
- * - only one ADM1021
- * - i2c addr 0x18
- * - conversion rate 0x02 = 0.25 conversions/second
- * - ALERT ouput disabled
- * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
- * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
- */
-#define CONFIG_SYS_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} }
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index b8c0d0d8f0..a91a6a9ee5 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -317,10 +317,6 @@
#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
#define CONFIG_4xx_CONFIG_BLOCKSIZE 16
-/* Standard DTT sensor configuration */
-#define CONFIG_DTT_DS1775 1
-#define CONFIG_DTT_SENSORS { 0 }
-
/* RTC configuration */
#define CONFIG_RTC_DS1338 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
diff --git a/include/configs/km/km-powerpc.h b/include/configs/km/km-powerpc.h
index 8293607c9c..0d50538a8e 100644
--- a/include/configs/km/km-powerpc.h
+++ b/include/configs/km/km-powerpc.h
@@ -14,7 +14,6 @@
#define CONFIG_BOOTCOUNT_LIMIT
-#define CONFIG_CMD_DTT
#define CONFIG_JFFS2_CMDLINE
/* standard km ethernet_present for piggy */
diff --git a/include/configs/km/km83xx-common.h b/include/configs/km/km83xx-common.h
index 35ec0972bf..7d69224bd1 100644
--- a/include/configs/km/km83xx-common.h
+++ b/include/configs/km/km83xx-common.h
@@ -215,13 +215,6 @@
#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0, 1, 2, 3} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-#define CONFIG_SYS_DTT_BUS_NUM 1
-
#if defined(CONFIG_CMD_NAND)
#define CONFIG_NAND_KMETER1
#define CONFIG_SYS_MAX_NAND_DEVICE 1
diff --git a/include/configs/km82xx.h b/include/configs/km82xx.h
index aeece20bda..09c3aa9ca8 100644
--- a/include/configs/km82xx.h
+++ b/include/configs/km82xx.h
@@ -268,13 +268,6 @@ int get_sda(void);
int get_scl(void);
#endif
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-#define CONFIG_SYS_DTT_BUS_NUM 2
-
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_IMMR 0xF0000000
diff --git a/include/configs/makalu.h b/include/configs/makalu.h
index cdb02f3693..a92bc43538 100644
--- a/include/configs/makalu.h
+++ b/include/configs/makalu.h
@@ -189,10 +189,6 @@
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* Standard DTT sensor configuration */
-#define CONFIG_DTT_DS1775 1
-#define CONFIG_DTT_SENSORS { 0 }
-
/* RTC configuration */
#define CONFIG_RTC_X1205 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x6f
@@ -231,7 +227,6 @@
/*
* Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_PCI
/* POST support */
diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h
index cb5c346807..aaa8962fd2 100644
--- a/include/configs/motionpro.h
+++ b/include/configs/motionpro.h
@@ -33,7 +33,6 @@
/*
* Command line configuration.
*/
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_IDE
#define CONFIG_CMD_IMMAP
#define CONFIG_CMD_JFFS2
@@ -268,6 +267,13 @@
#define LED_ON 0x00000010
/*
+<<<<<<< 4ba57299158b7a7020d2bd3b8d8369884696a0ae
+=======
+ * Temperature sensor
+ */
+
+/*
+>>>>>>> Drop digital thermometer and thermostat (DTT) drivers
* Environment settings
*/
#define CONFIG_ENV_IS_IN_FLASH 1
diff --git a/include/configs/neo.h b/include/configs/neo.h
index 9115e251b1..29ce61c326 100644
--- a/include/configs/neo.h
+++ b/include/configs/neo.h
@@ -57,7 +57,6 @@
/*
* Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_CMD_DTT
#undef CONFIG_CMD_EEPROM
#undef CONFIG_CMD_IRQ
@@ -100,13 +99,6 @@
#define CONFIG_RTC_DS1337
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-/* Temp sensor/hwmon/dtt */
-#define CONFIG_DTT_LM63 1 /* National LM63 */
-#define CONFIG_DTT_SENSORS { 0 } /* Sensor addresses */
-#define CONFIG_DTT_PWM_LOOKUPTABLE \
- { { 40, 10 }, { 50, 20 }, { 60, 40 } }
-#define CONFIG_DTT_TACH_LIMIT 0xa10
-
/*
* FLASH organization
*/
diff --git a/include/configs/odroid_xu3.h b/include/configs/odroid_xu3.h
index 246fb808a9..ba29f3e7d1 100644
--- a/include/configs/odroid_xu3.h
+++ b/include/configs/odroid_xu3.h
@@ -61,7 +61,6 @@
/* FIXME: MUST BE REMOVED AFTER TMU IS TURNED ON */
#undef CONFIG_EXYNOS_TMU
-#undef CONFIG_TMU_CMD_DTT
#define CONFIG_DFU_ALT_SYSTEM \
"uImage fat 0 1;" \
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index c39bb24420..7a120ed5a6 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -159,14 +159,6 @@
#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
#define CONFIG_4xx_CONFIG_BLOCKSIZE 16
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_AD7414 1 /* use AD7414 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-
/*
* Default environment variables
*/
@@ -219,7 +211,6 @@
/*
* Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SDRAM
diff --git a/include/configs/socrates.h b/include/configs/socrates.h
index 76b4038d50..b37e796d33 100644
--- a/include/configs/socrates.h
+++ b/include/configs/socrates.h
@@ -210,13 +210,6 @@
/* I2C W83782G HW-Monitoring IC */
#define CONFIG_SYS_I2C_W83782G_ADDR 0x28 /* W83782G address */
-/* I2C temp sensor */
-/* Socrates uses Maxim's DS75, which is compatible with LM75 */
-#define CONFIG_DTT_LM75 1
-#define CONFIG_DTT_SENSORS {4} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 125
-#define CONFIG_SYS_DTT_LOW_TEMP -55
-#define CONFIG_SYS_DTT_HYSTERESIS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
/*
@@ -286,7 +279,6 @@
/*
* Command line configuration.
*/
-#define CONFIG_CMD_DTT
#undef CONFIG_CMD_EEPROM
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_REGINFO
diff --git a/include/configs/tqma6.h b/include/configs/tqma6.h
index 738693c0c0..799c45e2d7 100644
--- a/include/configs/tqma6.h
+++ b/include/configs/tqma6.h
@@ -57,13 +57,6 @@
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED 100000
-/* I2C SYSMON (LM75) */
-#define CONFIG_DTT_LM75
-#define CONFIG_DTT_MAX_TEMP 70
-#define CONFIG_DTT_MIN_TEMP -30
-#define CONFIG_DTT_HYSTERESIS 3
-#define CONFIG_CMD_DTT
-
/* I2C EEPROM (M24C64) */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
@@ -371,8 +364,5 @@
#endif
/* Support at least the sensor on TQMa6 SOM */
-#if !defined(CONFIG_DTT_SENSORS)
-#define CONFIG_DTT_SENSORS { 0 }
-#endif
#endif /* __CONFIG_H */
diff --git a/include/configs/tqma6_mba6.h b/include/configs/tqma6_mba6.h
index 3d6e4383e1..69e9079339 100644
--- a/include/configs/tqma6_mba6.h
+++ b/include/configs/tqma6_mba6.h
@@ -10,8 +10,6 @@
#ifndef __CONFIG_TQMA6_MBA6_H
#define __CONFIG_TQMA6_MBA6_H
-#define CONFIG_DTT_SENSORS { 0, 1 }
-
#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_ETHPRIME "FEC"
diff --git a/include/configs/tqma6_wru4.h b/include/configs/tqma6_wru4.h
index b9cc5d632f..4ab4c6559d 100644
--- a/include/configs/tqma6_wru4.h
+++ b/include/configs/tqma6_wru4.h
@@ -7,10 +7,6 @@
#ifndef __CONFIG_TQMA6_WRU4_H
#define __CONFIG_TQMA6_WRU4_H
-/* DTT sensors */
-#define CONFIG_DTT_SENSORS { 0, 1 }
-#define CONFIG_SYS_DTT_BUS_NUM 2
-
/* Ethernet */
#define CONFIG_FEC_XCV_TYPE RMII
#define CONFIG_ETHPRIME "FEC"
diff --git a/include/configs/work_92105.h b/include/configs/work_92105.h
index 82f4af9c93..458acf59af 100644
--- a/include/configs/work_92105.h
+++ b/include/configs/work_92105.h
@@ -85,14 +85,6 @@
#define CONFIG_RTC_DS1374
/*
- * I2C Temperature Sensor (DTT)
- */
-
-#define CONFIG_CMD_DTT
-#define CONFIG_DTT_SENSORS { 0, 1 }
-#define CONFIG_DTT_DS620
-
-/*
* U-Boot General Configurations
*/
#define CONFIG_SYS_LONGHELP
diff --git a/include/configs/xilinx-ppc.h b/include/configs/xilinx-ppc.h
index ea4b739d0b..c4efae67a7 100644
--- a/include/configs/xilinx-ppc.h
+++ b/include/configs/xilinx-ppc.h
@@ -28,7 +28,6 @@
#define CONFIG_CMD_REGINFO
#undef CONFIG_CMD_JFFS2
#undef CONFIG_CMD_MTDPARTS
-#undef CONFIG_CMD_DTT
#undef CONFIG_CMD_EEPROM
/*Misc*/
diff --git a/include/configs/xpedite517x.h b/include/configs/xpedite517x.h
index bd1d0c75d9..97a9d71e8b 100644
--- a/include/configs/xpedite517x.h
+++ b/include/configs/xpedite517x.h
@@ -233,8 +233,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
/* I2C DS1631 temperature sensor */
#define CONFIG_SYS_I2C_DS1621_ADDR 0x48
-#define CONFIG_DTT_DS1621
-#define CONFIG_DTT_SENSORS { 0 }
#define CONFIG_SYS_I2C_LM90_ADDR 0x4c
/* I2C EEPROM - AT24C128B */
@@ -501,7 +499,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
/*
* Command configuration.
*/
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_JFFS2
diff --git a/include/configs/xpedite537x.h b/include/configs/xpedite537x.h
index a290cf3463..fa1971db20 100644
--- a/include/configs/xpedite537x.h
+++ b/include/configs/xpedite537x.h
@@ -230,8 +230,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
/* I2C DS1631 temperature sensor */
#define CONFIG_SYS_I2C_DS1621_ADDR 0x48
-#define CONFIG_DTT_DS1621
-#define CONFIG_DTT_SENSORS { 0 }
#define CONFIG_SYS_I2C_LM90_ADDR 0x4c
/* I2C EEPROM - AT24C128B */
@@ -353,7 +351,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
/*
* Command configuration.
*/
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_NAND
diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h
index ad4247ab48..e3f0b939c3 100644
--- a/include/configs/xpedite550x.h
+++ b/include/configs/xpedite550x.h
@@ -219,8 +219,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/* I2C DS7505 temperature sensor */
-#define CONFIG_DTT_LM75
-#define CONFIG_DTT_SENSORS { 0 }
#define CONFIG_SYS_I2C_LM75_ADDR 0x48
/* I2C ADT7461 temperature sensor */
@@ -338,7 +336,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
/*
* Command configuration.
*/
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_NAND
diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h
index 77648d78bc..d9c09b80cd 100644
--- a/include/configs/yosemite.h
+++ b/include/configs/yosemite.h
@@ -131,14 +131,6 @@
#define CONFIG_ENV_OFFSET 0x0
#endif /* CONFIG_ENV_IS_IN_EEPROM */
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_AD7414 1 /* use AD7414 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-
/*
* Default environment variables
*/
@@ -184,7 +176,6 @@
/*
* Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_PCI
#ifdef CONFIG_440EP
diff --git a/include/dtt.h b/include/dtt.h
deleted file mode 100644
index 173159dc62..0000000000
--- a/include/dtt.h
+++ /dev/null
@@ -1,47 +0,0 @@
-/*
- * (C) Copyright 2001
- * Erik Theisen, Wave 7 Optics, etheisen at mindspring.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * Digital Thermometers and Thermostats.
- */
-#ifndef _DTT_H_
-#define _DTT_H_
-
-#if defined(CONFIG_DTT_ADM1021) || \
- defined(CONFIG_DTT_ADT7460) || \
- defined(CONFIG_DTT_DS1621) || \
- defined(CONFIG_DTT_DS1775) || \
- defined(CONFIG_DTT_DS620) || \
- defined(CONFIG_DTT_LM63) || \
- defined(CONFIG_DTT_LM73) || \
- defined(CONFIG_DTT_LM75) || \
- defined(CONFIG_DTT_LM81)
-
-#define CONFIG_DTT /* We have a DTT */
-
-#ifndef CONFIG_DTT_ADM1021
-#define DTT_COMMERCIAL_MAX_TEMP 70 /* 0 - +70 C */
-#define DTT_INDUSTRIAL_MAX_TEMP 85 /* -40 - +85 C */
-#define DTT_AUTOMOTIVE_MAX_TEMP 105 /* -40 - +105 C */
-
-#ifndef CONFIG_SYS_DTT_MAX_TEMP
-#define CONFIG_SYS_DTT_MAX_TEMP DTT_COMMERCIAL_MAX_TEMP
-#endif
-
-#ifndef CONFIG_SYS_DTT_HYSTERESIS
-#define CONFIG_SYS_DTT_HYSTERESIS 5 /* 5 C */
-#endif
-#endif /* CONFIG_DTT_ADM1021 */
-
-extern void dtt_init(void);
-extern int dtt_init_one(int);
-extern int dtt_read(int sensor, int reg);
-extern int dtt_write(int sensor, int reg, int val);
-extern int dtt_get_temp(int sensor);
-#endif
-
-#endif /* _DTT_H_ */
diff --git a/include/i2c.h b/include/i2c.h
index a88cc7cddf..2c1643d650 100644
--- a/include/i2c.h
+++ b/include/i2c.h
@@ -571,9 +571,6 @@ void i2c_dump_msgs(struct i2c_msg *msg, int nmsgs);
#if !defined(CONFIG_SYS_RTC_BUS_NUM)
#define CONFIG_SYS_RTC_BUS_NUM 0
#endif
-#if !defined(CONFIG_SYS_DTT_BUS_NUM)
-#define CONFIG_SYS_DTT_BUS_NUM 0
-#endif
#if !defined(CONFIG_SYS_SPD_BUS_NUM)
#define CONFIG_SYS_SPD_BUS_NUM 0
#endif
diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
index 5a9eae3b69..ae3e0ec3fc 100644
--- a/scripts/config_whitelist.txt
+++ b/scripts/config_whitelist.txt
@@ -384,7 +384,6 @@ CONFIG_CM922T_XA10
CONFIG_CMDLINE_EDITING
CONFIG_CMDLINE_PS_SUPPORT
CONFIG_CMDLINE_TAG
-CONFIG_CMD_DTT
CONFIG_CMD_ECCTEST
CONFIG_CMD_EECONFIG
CONFIG_CMD_EEPROM
@@ -683,20 +682,6 @@ CONFIG_DRIVE_SATA
CONFIG_DRIVE_TYPES
CONFIG_DRIVE_USB
CONFIG_DSP_CLUSTER_START
-CONFIG_DTT
-CONFIG_DTT_AD7414
-CONFIG_DTT_ADM1021
-CONFIG_DTT_DS1621
-CONFIG_DTT_DS1775
-CONFIG_DTT_DS620
-CONFIG_DTT_HYSTERESIS
-CONFIG_DTT_LM63
-CONFIG_DTT_LM75
-CONFIG_DTT_MAX_TEMP
-CONFIG_DTT_MIN_TEMP
-CONFIG_DTT_PWM_LOOKUPTABLE
-CONFIG_DTT_SENSORS
-CONFIG_DTT_TACH_LIMIT
CONFIG_DUOVERO
CONFIG_DV_USBPHY_CTL
CONFIG_DWC2_DFLT_SPEED_FULL
@@ -3452,12 +3437,6 @@ CONFIG_SYS_DSPI_CTAR4
CONFIG_SYS_DSPI_CTAR5
CONFIG_SYS_DSPI_CTAR6
CONFIG_SYS_DSPI_CTAR7
-CONFIG_SYS_DTT_ADM1021
-CONFIG_SYS_DTT_BUS_NUM
-CONFIG_SYS_DTT_HYSTERESIS
-CONFIG_SYS_DTT_LOW_TEMP
-CONFIG_SYS_DTT_MAX_TEMP
-CONFIG_SYS_DTT_MIN_TEMP
CONFIG_SYS_DUART_RST
CONFIG_SYS_DV_CLKMODE
CONFIG_SYS_DV_NOR_BOOT_CFG
@@ -6117,7 +6096,6 @@ CONFIG_TIZEN
CONFIG_TI_KEYSTONE_SERDES
CONFIG_TI_KSNAV
CONFIG_TI_SPI_MMAP
-CONFIG_TMU_CMD_DTT
CONFIG_TMU_TIMER
CONFIG_TOTAL5200
CONFIG_TPL_DRIVERS_MISC_SUPPORT
--
2.13.0.303.g4ebf302169-goog
More information about the U-Boot
mailing list