From: Jagan Teki <jagan at amarulasolutions.com>
(1) Enable
DM_I2C
DM_PMIC
DM_PMIC_PFUZE100
(2) Removed
setup_i2c
power_init_board
I2C Log:
--------
=> i2c bus
Bus 0: i2c at 021a0000
Bus 1: i2c at 021a4000
08: pfuze100 at 08, offset len 1, flags 0
Bus 2: i2c at 021a8000
=> i2c dev 1
Setting bus to 1
=> i2c speed 100000
Setting bus speed to 100000 Hz
=> i2c probe
Valid chip addresses: 08 48
=> i2c md 08 0x0 0x20
0000: 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 ................
0010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
=> i2c md 48 0x0 0x20
0000: 00 f0 00 00 00 00 00 00 00 00 00 80 70 41 41 41 ............pAAA
0010: 00 00 00 80 70 41 41 41 41 41 41 41 41 41 41 41 ....pAAAAAAAAAAA
Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
---
arch/arm/cpu/armv7/mx6/Kconfig | 3 ++
board/freescale/mx6sabresd/mx6sabresd.c | 72 ---------------------------------
include/configs/mx6sabresd.h | 15 -------
3 files changed, 3 insertions(+), 87 deletions(-)
diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
index 42ac9b9..314a61f 100644
--- a/arch/arm/cpu/armv7/mx6/Kconfig
+++ b/arch/arm/cpu/armv7/mx6/Kconfig
@@ -214,8 +214,11 @@ config TARGET_MX6SABRESD
select BOARD_LATE_INIT
select OF_CONTROL
select DM
+ select DM_I2C
select DM_GPIO
select DM_MMC
+ select DM_PMIC
+ select DM_PMIC_PFUZE100
select DM_THERMAL
select PINCTRL
select PINCTRL_IMX6
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 7af263d..cbd952f 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -12,7 +12,6 @@
#include <asm/arch/mx6-pins.h>
#include <linux/errno.h>
#include <asm/gpio.h>
-#include <asm/imx-common/mxc_i2c.h>
#include <asm/imx-common/iomux-v3.h>
#include <asm/imx-common/boot_mode.h>
#include <asm/imx-common/video.h>
@@ -22,10 +21,6 @@
#include <asm/arch/crm_regs.h>
#include <asm/io.h>
#include <asm/arch/sys_proto.h>
-#include <i2c.h>
-#include <power/pmic.h>
-#include <power/pfuze100_pmic.h>
-#include "../common/pfuze.h"
#include <usb.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -40,14 +35,6 @@ DECLARE_GLOBAL_DATA_PTR;
#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
-#define I2C_PMIC 1
-
-#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
-
#define DISP0_PWR_EN IMX_GPIO_NR(1, 21)
int dram_init(void)
@@ -152,32 +139,6 @@ static void enable_lvds(struct display_info_t const *dev)
enable_backlight();
}
-static struct i2c_pads_info mx6q_i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
- .gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 12)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
- .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
-static struct i2c_pads_info mx6dl_i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6DL_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
- .gpio_mode = MX6DL_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 12)
- },
- .sda = {
- .i2c_mode = MX6DL_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
- .gpio_mode = MX6DL_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
static void setup_spi(void)
{
SETUP_IOMUX_PADS(ecspi1_pads);
@@ -471,10 +432,6 @@ int board_init(void)
#ifdef CONFIG_MXC_SPI
setup_spi();
#endif
- if (is_mx6dq() || is_mx6dqp())
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1);
- else
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1);
#ifdef CONFIG_USB_EHCI_MX6
setup_usb();
#endif
@@ -482,35 +439,6 @@ int board_init(void)
return 0;
}
-int power_init_board(void)
-{
- struct pmic *p;
- unsigned int reg;
- int ret;
-
- p = pfuze_common_init(I2C_PMIC);
- if (!p)
- return -ENODEV;
-
- ret = pfuze_mode_init(p, APS_PFM);
- if (ret < 0)
- return ret;
-
- /* Increase VGEN3 from 2.5 to 2.8V */
- pmic_reg_read(p, PFUZE100_VGEN3VOL, ®);
- reg &= ~LDO_VOL_MASK;
- reg |= LDOB_2_80V;
- pmic_reg_write(p, PFUZE100_VGEN3VOL, reg);
-
- /* Increase VGEN5 from 2.8 to 3V */
- pmic_reg_read(p, PFUZE100_VGEN5VOL, ®);
- reg &= ~LDO_VOL_MASK;
- reg |= LDOB_3_00V;
- pmic_reg_write(p, PFUZE100_VGEN5VOL, reg);
-
- return 0;
-}
-
#ifdef CONFIG_MXC_SPI
int board_spi_cs_gpio(unsigned bus, unsigned cs)
{
diff --git a/include/configs/mx6sabresd.h b/include/configs/mx6sabresd.h
index b90afe0..9d82355 100644
--- a/include/configs/mx6sabresd.h
+++ b/include/configs/mx6sabresd.h
@@ -50,21 +50,6 @@
#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(3, 19)
#endif
-/* I2C Configs */
-#ifdef CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
-#define CONFIG_SYS_I2C_SPEED 100000
-#endif
-
-/* PMIC */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_PFUZE100
-#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
-
/* USB Configs */
#ifdef CONFIG_CMD_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
--
1.9.1