[U-Boot] [PATCH v7 12/17] SabreSD: Enable DM_USB

[Jagan Teki]

From: Jagan Teki <jagan at openedev.com>

Enable DM_USB and removed non-DM_USB related config options.

Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam at nxp.com>
---
 arch/arm/cpu/armv7/mx6/Kconfig          |  1 +
 board/freescale/mx6sabresd/mx6sabresd.c | 65 ---------------------------------
 include/configs/mx6sabresd.h            | 11 ++----
 3 files changed, 5 insertions(+), 72 deletions(-)

diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
index f203cf6..d1ba801 100644
--- a/arch/arm/cpu/armv7/mx6/Kconfig
+++ b/arch/arm/cpu/armv7/mx6/Kconfig
@@ -218,6 +218,7 @@ config TARGET_MX6SABRESD
 	select DM_MMC
 	select DM_REGULATOR
 	select DM_THERMAL
+	select DM_USB
 	select PINCTRL
 	select PINCTRL_IMX6
 	select SUPPORT_SPL
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 7af263d..688b326 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -26,7 +26,6 @@
 #include <power/pmic.h>
 #include <power/pfuze100_pmic.h>
 #include "../common/pfuze.h"
-#include <usb.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -392,67 +391,6 @@ int board_eth_init(bd_t *bis)
 	return cpu_eth_init(bis);
 }
 
-#ifdef CONFIG_USB_EHCI_MX6
-#define USB_OTHERREGS_OFFSET	0x800
-#define UCTRL_PWR_POL		(1 << 9)
-
-static iomux_v3_cfg_t const usb_otg_pads[] = {
-	IOMUX_PADS(PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)),
-	IOMUX_PADS(PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-static iomux_v3_cfg_t const usb_hc1_pads[] = {
-	IOMUX_PADS(PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-static void setup_usb(void)
-{
-	SETUP_IOMUX_PADS(usb_otg_pads);
-
-	/*
-	 * set daisy chain for otg_pin_id on 6q.
-	 * for 6dl, this bit is reserved
-	 */
-	imx_iomux_set_gpr_register(1, 13, 1, 0);
-
-	SETUP_IOMUX_PADS(usb_hc1_pads);
-}
-
-int board_ehci_hcd_init(int port)
-{
-	u32 *usbnc_usb_ctrl;
-
-	if (port > 1)
-		return -EINVAL;
-
-	usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
-				 port * 4);
-
-	setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
-
-	return 0;
-}
-
-int board_ehci_power(int port, int on)
-{
-	switch (port) {
-	case 0:
-		break;
-	case 1:
-		if (on)
-			gpio_direction_output(IMX_GPIO_NR(1, 29), 1);
-		else
-			gpio_direction_output(IMX_GPIO_NR(1, 29), 0);
-		break;
-	default:
-		printf("MXC USB port %d not yet supported\n", port);
-		return -EINVAL;
-	}
-
-	return 0;
-}
-#endif
-
 int board_early_init_f(void)
 {
 	setup_iomux_uart();
@@ -475,9 +413,6 @@ int board_init(void)
 		setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1);
 	else
 		setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1);
-#ifdef CONFIG_USB_EHCI_MX6
-	setup_usb();
-#endif
 
 	return 0;
 }
diff --git a/include/configs/mx6sabresd.h b/include/configs/mx6sabresd.h
index b90afe0..44c7cf6 100644
--- a/include/configs/mx6sabresd.h
+++ b/include/configs/mx6sabresd.h
@@ -66,13 +66,10 @@
 #define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
 
 /* USB Configs */
-#ifdef CONFIG_CMD_USB
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_ASIX
-#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS		0
-#define CONFIG_USB_MAX_CONTROLLER_COUNT	1 /* Enabled USB controller number */
+#ifdef CONFIG_USB_EHCI_MX6
+# define CONFIG_USB_HOST_ETHER
+# define CONFIG_USB_ETHER_ASIX
+# define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
 #endif
 
 #endif                         /* __MX6QSABRESD_CONFIG_H */
-- 
1.9.1