[U-Boot] [PATCH v7 15/17] i.MX6: SabreSD: Enable DM_ETH

[Jagan Teki]

From: Jagan Teki <jagan at openedev.com>

(1) Enable DM_ETH
(2) Droped board_eth_init

Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam at nxp.com>
---
 arch/arm/cpu/armv7/mx6/Kconfig          |  1 +
 board/freescale/mx6sabresd/mx6sabresd.c | 45 ++-------------------------------
 2 files changed, 3 insertions(+), 43 deletions(-)

diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
index d1ba801..f4c8c39 100644
--- a/arch/arm/cpu/armv7/mx6/Kconfig
+++ b/arch/arm/cpu/armv7/mx6/Kconfig
@@ -214,6 +214,7 @@ config TARGET_MX6SABRESD
 	select BOARD_LATE_INIT
 	select OF_CONTROL
 	select DM
+	select DM_ETH
 	select DM_GPIO
 	select DM_MMC
 	select DM_REGULATOR
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 688b326..7eab021 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -17,7 +17,6 @@
 #include <asm/imx-common/boot_mode.h>
 #include <asm/imx-common/video.h>
 #include <miiphy.h>
-#include <netdev.h>
 #include <asm/arch/mxc_hdmi.h>
 #include <asm/arch/crm_regs.h>
 #include <asm/io.h>
@@ -33,9 +32,6 @@ DECLARE_GLOBAL_DATA_PTR;
 	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
 	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
 
-#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
-	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
 #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
 		      PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
 
@@ -60,37 +56,6 @@ static iomux_v3_cfg_t const uart1_pads[] = {
 	IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
 };
 
-static iomux_v3_cfg_t const enet_pads[] = {
-	IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_ENET_MDC__ENET_MDC	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
-	/* AR8031 PHY Reset */
-	IOMUX_PADS(PAD_ENET_CRS_DV__GPIO1_IO25	| MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-static void setup_iomux_enet(void)
-{
-	SETUP_IOMUX_PADS(enet_pads);
-
-	/* Reset AR8031 PHY */
-	gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
-	mdelay(10);
-	gpio_set_value(IMX_GPIO_NR(1, 25), 1);
-	udelay(100);
-}
-
 static iomux_v3_cfg_t const ecspi1_pads[] = {
 	IOMUX_PADS(PAD_KEY_COL0__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)),
 	IOMUX_PADS(PAD_KEY_COL1__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)),
@@ -383,14 +348,6 @@ int overwrite_console(void)
 	return 1;
 }
 
-int board_eth_init(bd_t *bis)
-{
-	setup_iomux_enet();
-	setup_pcie();
-
-	return cpu_eth_init(bis);
-}
-
 int board_early_init_f(void)
 {
 	setup_iomux_uart();
@@ -414,6 +371,8 @@ int board_init(void)
 	else
 		setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1);
 
+	setup_pcie();
+
 	return 0;
 }
 
-- 
1.9.1