[U-Boot] [PATCH v7 00/17] ARM: i.MX6: SabreSD: Add dts support

[Jagan Teki]

On Fri, May 26, 2017 at 10:34 PM, Fabio Estevam <festevam at gmail.com> wrote:
> On Fri, May 26, 2017 at 1:55 PM, Jagan Teki <jagannadh.teki at gmail.com> wrote:
>
>> No, PMIC and I2C are as it is like old code, I never did any
>> modification to use it for dts since driver require dm.
>
> Let me try to clarify the problem.
>
> If I use the latest u-boot-imx:
>
> U-Boot SPL 2017.05-35079-g4c78028 (May 26 2017 - 13:58:48)
> Trying to boot from MMC1
>
>
> U-Boot 2017.05-35079-g4c78028 (May 26 2017 - 13:58:48 -0300)
>
> CPU:   Freescale i.MX6Q rev1.1 at 792MHz
> CPU:   Commercial temperature grade (0C to 95C) at 31C
> Reset cause: POR
> Board: MX6-SabreSD
> I2C:   ready
> DRAM:  1 GiB
> PMIC:  PFUZE100 ID=0x10
> MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
> PCI:   pcie phy link never came up
> No panel detected: default to Hannstar-XGA
> Display: Hannstar-XGA (1024x768)
> In:    serial
> Out:   serial
> Err:   serial
> Net:   FEC [PRIME]
> Hit any key to stop autoboot:  0
> => pmic
> pmic - PMIC
>
> Usage:
> pmic list - list available PMICs
> pmic name dump - dump named PMIC registers
> pmic name read <reg> - read register
> pmic name write <reg> <value> - write register
> pmic name bat state - write register
> pmic name bat charge - write register
>
> If I use your series:
>
> U-Boot SPL 2017.05-rc3-00037-g60e903a (May 26 2017 - 14:02:35)
> Trying to boot from MMC1
>
>
> U-Boot 2017.05-rc3-00037-g60e903a (May 26 2017 - 14:02:35 -0300)
>
> CPU:   Freescale i.MX6Q rev1.1 at 792MHz
> CPU:   Commercial temperature grade (0C to 95C) at 38C
> Reset cause: POR
> Model: Freescale i.MX6 Quad SABRE Smart Device Board
> DRAM:  1 GiB
> MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
> PCI:   pcie phy link never came up
> No panel detected: default to Hannstar-XGA
> Display: Hannstar-XGA (1024x768)
> In:    serial
> Out:   serial
> Err:   serial
> Net:   eth0: ethernet at 02188000
> Hit any key to stop autoboot:  0
> => pmic
> Unknown command 'pmic' - try 'help'

Can you please confirm, are you using v7 series? in this I kept the
PMIC as it is.

/* PMIC */
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_PFUZE100
#define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08

thanks!



-- 
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.