[U-Boot] [PATCH v4 1/2] wandboard: Add support for the latest revd1 revision
Stefano Babic
sbabic at denx.de
Wed Oct 4 09:27:02 UTC 2017
On 02/10/2017 20:47, Fabio Estevam wrote:
> From: Fabio Estevam <fabio.estevam at nxp.com>
>
> Latest wandboard hardware revision is revd1, which brings the following
> new features:
>
> - PFUZE100 PMIC
> - AR8035 Ethernet PHY
> - Upgrade Wifi/BT chip to BCM4339/BCM43430.
>
> The detection mechanism is to probe the PMIC and when it is
> found, then the revision of the board is revd1.
>
> As the detection is done via PMIC, we need to print the board version
> at a later stage via CONFIG_DISPLAY_BOARDINFO_LATE and also need
> to disable CONFIG_DISPLAY_BOARDINFO, which is done much earlier.
>
> Make the necessary adjustments for the AR8035 PHY to work on revd1.
>
> Based on Richard Hu's work from Technexion's U-Boot tree.
>
> Signed-off-by: Fabio Estevam <fabio.estevam at nxp.com>
> ---
> Changes since v3:
> - Rebased against latest u-boot-imx
>
> board/wandboard/wandboard.c | 108 ++++++++++++++++++++++++++++++++++++++++++--
> configs/wandboard_defconfig | 1 +
> include/configs/wandboard.h | 11 +++++
> 3 files changed, 115 insertions(+), 5 deletions(-)
>
> diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c
> index dde4988..6d2609c 100644
> --- a/board/wandboard/wandboard.c
> +++ b/board/wandboard/wandboard.c
> @@ -30,6 +30,8 @@
> #include <phy.h>
> #include <input.h>
> #include <i2c.h>
> +#include <power/pmic.h>
> +#include <power/pfuze100_pmic.h>
>
> DECLARE_GLOBAL_DATA_PTR;
>
> @@ -51,8 +53,11 @@ DECLARE_GLOBAL_DATA_PTR;
> #define USDHC1_CD_GPIO IMX_GPIO_NR(1, 2)
> #define USDHC3_CD_GPIO IMX_GPIO_NR(3, 9)
> #define ETH_PHY_RESET IMX_GPIO_NR(3, 29)
> +#define ETH_PHY_AR8035_POWER IMX_GPIO_NR(7, 13)
> #define REV_DETECTION IMX_GPIO_NR(2, 28)
>
> +static bool with_pmic;
> +
> int dram_init(void)
> {
> gd->ram_size = imx_ddr_size();
> @@ -107,6 +112,11 @@ static iomux_v3_cfg_t const enet_pads[] = {
> IOMUX_PADS(PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)),
> };
>
> +static iomux_v3_cfg_t const enet_ar8035_power_pads[] = {
> + /* AR8035 POWER */
> + IOMUX_PADS(PAD_GPIO_18__GPIO7_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL)),
> +};
> +
> static iomux_v3_cfg_t const rev_detection_pad[] = {
> IOMUX_PADS(PAD_EIM_EB0__GPIO2_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL)),
> };
> @@ -120,6 +130,14 @@ static void setup_iomux_enet(void)
> {
> SETUP_IOMUX_PADS(enet_pads);
>
> + if (with_pmic) {
> + SETUP_IOMUX_PADS(enet_ar8035_power_pads);
> + /* enable AR8035 POWER */
> + gpio_direction_output(ETH_PHY_AR8035_POWER, 0);
> + }
> + /* wait until 3.3V of PHY and clock become stable */
> + mdelay(10);
> +
> /* Reset AR8031 PHY */
> gpio_direction_output(ETH_PHY_RESET, 0);
> mdelay(10);
> @@ -192,6 +210,7 @@ int board_mmc_init(bd_t *bis)
> static int ar8031_phy_fixup(struct phy_device *phydev)
> {
> unsigned short val;
> + int mask;
>
> /* To enable AR8031 ouput a 125MHz clk from CLK_25M */
> phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
> @@ -199,7 +218,12 @@ static int ar8031_phy_fixup(struct phy_device *phydev)
> phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
>
> val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
> - val &= 0xffe3;
> + if (with_pmic)
> + mask = 0xffe7; /* AR8035 */
> + else
> + mask = 0xffe3; /* AR8031 */
> +
> + val &= mask;
> val |= 0x18;
> phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
>
> @@ -257,6 +281,40 @@ struct i2c_pads_info mx6dl_i2c2_pad_info = {
> }
> };
>
> +struct i2c_pads_info mx6q_i2c3_pad_info = {
> + .scl = {
> + .i2c_mode = MX6Q_PAD_GPIO_5__I2C3_SCL
> + | MUX_PAD_CTRL(I2C_PAD_CTRL),
> + .gpio_mode = MX6Q_PAD_GPIO_5__GPIO1_IO05
> + | MUX_PAD_CTRL(I2C_PAD_CTRL),
> + .gp = IMX_GPIO_NR(1, 5)
> + },
> + .sda = {
> + .i2c_mode = MX6Q_PAD_GPIO_16__I2C3_SDA
> + | MUX_PAD_CTRL(I2C_PAD_CTRL),
> + .gpio_mode = MX6Q_PAD_GPIO_16__GPIO7_IO11
> + | MUX_PAD_CTRL(I2C_PAD_CTRL),
> + .gp = IMX_GPIO_NR(7, 11)
> + }
> +};
> +
> +struct i2c_pads_info mx6dl_i2c3_pad_info = {
> + .scl = {
> + .i2c_mode = MX6DL_PAD_GPIO_5__I2C3_SCL
> + | MUX_PAD_CTRL(I2C_PAD_CTRL),
> + .gpio_mode = MX6DL_PAD_GPIO_5__GPIO1_IO05
> + | MUX_PAD_CTRL(I2C_PAD_CTRL),
> + .gp = IMX_GPIO_NR(1, 5)
> + },
> + .sda = {
> + .i2c_mode = MX6DL_PAD_GPIO_16__I2C3_SDA
> + | MUX_PAD_CTRL(I2C_PAD_CTRL),
> + .gpio_mode = MX6DL_PAD_GPIO_16__GPIO7_IO11
> + | MUX_PAD_CTRL(I2C_PAD_CTRL),
> + .gp = IMX_GPIO_NR(7, 11)
> + }
> +};
> +
> static iomux_v3_cfg_t const fwadapt_7wvga_pads[] = {
> IOMUX_PADS(PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK),
> IOMUX_PADS(PAD_DI0_PIN2__IPU1_DI0_PIN02), /* HSync */
> @@ -385,6 +443,31 @@ int board_early_init_f(void)
> return 0;
> }
>
> +#define PMIC_I2C_BUS 2
> +
> +int power_init_board(void)
> +{
> + struct pmic *p;
> + u32 reg;
> +
> + /* configure PFUZE100 PMIC */
> + power_pfuze100_init(PMIC_I2C_BUS);
> + p = pmic_get("PFUZE100");
> + if (p && !pmic_probe(p)) {
> + pmic_reg_read(p, PFUZE100_DEVICEID, ®);
> + printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
> + with_pmic = true;
> +
> + /* Set VGEN2 to 1.5V and enable */
> + pmic_reg_read(p, PFUZE100_VGEN2VOL, ®);
> + reg &= ~(LDO_VOL_MASK);
> + reg |= (LDOA_1_50V | (1 << (LDO_EN)));
> + pmic_reg_write(p, PFUZE100_VGEN2VOL, reg);
> + }
> +
> + return 0;
> +}
> +
> /*
> * Do not overwrite the console
> * Use always serial for U-Boot console
> @@ -414,6 +497,14 @@ static bool is_revc1(void)
> return false;
> }
>
> +static bool is_revd1(void)
> +{
> + if (with_pmic)
> + return true;
> + else
> + return false;
> +}
> +
> int board_late_init(void)
> {
> #ifdef CONFIG_CMD_BMODE
> @@ -426,7 +517,9 @@ int board_late_init(void)
> else
> env_set("board_rev", "MX6DL");
>
> - if (is_revc1())
> + if (is_revd1())
> + env_set("board_name", "D1");
> + else if (is_revc1())
> env_set("board_name", "C1");
> else
> env_set("board_name", "B1");
> @@ -441,10 +534,13 @@ int board_init(void)
>
> #if defined(CONFIG_VIDEO_IPUV3)
> setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c2_pad_info);
> - if (is_mx6dq())
> + if (is_mx6dq()) {
> setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c2_pad_info);
> - else
> + setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c3_pad_info);
> + } else {
> setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c2_pad_info);
> + setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c3_pad_info);
> + }
>
> setup_display();
> #endif
> @@ -454,7 +550,9 @@ int board_init(void)
>
> int checkboard(void)
> {
> - if (is_revc1())
> + if (is_revd1())
> + puts("Board: Wandboard rev D1\n");
> + else if (is_revc1())
> puts("Board: Wandboard rev C1\n");
> else
> puts("Board: Wandboard rev B1\n");
> diff --git a/configs/wandboard_defconfig b/configs/wandboard_defconfig
> index 9765f13..8097e6e 100644
> --- a/configs/wandboard_defconfig
> +++ b/configs/wandboard_defconfig
> @@ -15,6 +15,7 @@ CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,MX6QDL"
> # CONFIG_CONSOLE_MUX is not set
> CONFIG_SYS_CONSOLE_IS_IN_ENV=y
> CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
> +# CONFIG_DISPLAY_BOARDINFO is not set
> CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_SPL=y
> CONFIG_SPL_EXT_SUPPORT=y
> diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h
> index 3ba4c29..ba88d02 100644
> --- a/include/configs/wandboard.h
> +++ b/include/configs/wandboard.h
> @@ -13,6 +13,7 @@
> #include "mx6_common.h"
>
> #include "imx6_spl.h"
> +#define CONFIG_DISPLAY_BOARDINFO_LATE
>
> #define CONFIG_MACH_TYPE MACH_TYPE_WANDBOARD_IMX6
>
> @@ -44,6 +45,12 @@
> #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
> #define CONFIG_SYS_I2C_SPEED 100000
>
> +/* PMIC */
> +#define CONFIG_POWER
> +#define CONFIG_POWER_I2C
> +#define CONFIG_POWER_PFUZE100
> +#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
> +
> /* MMC Configuration */
> #define CONFIG_SYS_FSL_USDHC_NUM 2
> #define CONFIG_SYS_FSL_ESDHC_ADDR 0
> @@ -102,6 +109,10 @@
> "fi; " \
> "fi\0" \
> "findfdt="\
> + "if test $board_name = D1 && test $board_rev = MX6Q ; then " \
> + "setenv fdtfile imx6q-wandboard-revd1.dtb; fi; " \
> + "if test $board_name = D1 && test $board_rev = MX6DL ; then " \
> + "setenv fdtfile imx6dl-wandboard-revd1.dtb; fi; " \
> "if test $board_name = C1 && test $board_rev = MX6Q ; then " \
> "setenv fdtfile imx6q-wandboard.dtb; fi; " \
> "if test $board_name = C1 && test $board_rev = MX6DL ; then " \
>
Applied to u-boot-imx, -master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
More information about the U-Boot
mailing list