[U-Boot] [RFC] usb: musb-new: omap2430: Enable DM_USB and OF support
Adam Ford
aford173 at gmail.com
Tue Jul 31 09:57:07 UTC 2018
On Sun, Jul 22, 2018 at 3:31 PM Lukasz Majewski <lukma at denx.de> wrote:
>
> Hi Adam,
>
> > On Sun, Jul 22, 2018 at 11:45 AM Adam Ford <aford173 at gmail.com> wrote:
> > >
> > > With upcoming changes that require CONFIG_BLK, this broke
> > > USB Mass Storage on the OMAP3 boards because if CONFIG_BLK is
> > > enabled, it assumes that DM_USB is enabled, but it wasn't yet
> > > available on omap3 and omap4 boards.
> > >
> > > This patch converts the OMAP2430 MUSB glue to support DM_USB and
> > > extracts the necessary information based on the device tree.
> > >
> > > It's based on the ti-musb driver, but there are enough significant
> > > differences in both the architecture and device tree entires between
> > > am33xx and OMAP3/OMAP4, that I think it makes sense to continue to
> > > keep the separate.
> > >
> >
> > I forgot to mention that, I based this patch on top of an existing
> > patch, that hasn't yet been reviewed which strips out a bunch of dead
> > code
> > https://patchwork.ozlabs.org/patch/943813/
> >
> > I did it to make it easier for me to read.
> >
> > > This RFC has functional USB Host working, but it's hard coded to be
> > > host or peripheral based on the config file. Unfortunately,
> > > USB Peripherals like fastboot, etc don't appear to be
> > > working at all. At least on omap3_logic (DM3730/OMAP35xx).
> > > Any suggestions are appreciated in how to setup the MUSB in OTG mode
> > > and get it to start USB in either host or gadget mode.
>
> Has it been working from the outset? Is the old musb driver working
> correctly with gadget infrastructure?
Currently, the omap3_logic board selects the USB_MUSB_GADGET using the
new MUSB driver. Host is disabled, but when I do usb start, the
device enumerates.
When I enact fastboot usb 0, my host PC shows
[307816.691237] usb 3-2: USB disconnect, device number 39
[307866.180431] usb 3-2: new high-speed USB device number 41 using xhci_hcd
[307866.328908] usb 3-2: New USB device found, idVendor=0451, idProduct=d022
[307866.328912] usb 3-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[307866.328914] usb 3-2: Product: USB download gadget
[307866.328916] usb 3-2: Manufacturer: TI
>
> > >
> > > Unless an OTG adapter is connected with a USB device, the only
> > > message I get when issing 'usb start' is
> > >
> > > USB0: Port not available.
>
> I assume that without your patches it works? It was not clear from your
> commit message.
>
In gadget mode, yet, see above.
> > >
> > > Signed-off-by: Adam Ford <aford173 at gmail.com>
> > >
> > > diff --git a/drivers/usb/musb-new/omap2430.c
> > > b/drivers/usb/musb-new/omap2430.c index fd63c07789..8b56e1a42a
> > > 100644 --- a/drivers/usb/musb-new/omap2430.c
> > > +++ b/drivers/usb/musb-new/omap2430.c
> > > @@ -9,14 +9,18 @@
> > > * This file is part of the Inventra Controller Driver for Linux.
> > > */
> > > #include <common.h>
> > > +#include <dm.h>
> > > +#include <dm/device-internal.h>
> > > +#include <dm/lists.h>
> > > +#include <linux/usb/otg.h>
> > > #include <asm/omap_common.h>
> > > #include <asm/omap_musb.h>
> > > #include <twl4030.h>
> > > #include <twl6030.h>
> > > #include "linux-compat.h"
> > > -
> > > #include "musb_core.h"
> > > #include "omap2430.h"
> > > +#include "musb_uboot.h"
> > >
> > > static inline void omap2430_low_level_exit(struct musb *musb)
> > > {
> > > @@ -43,6 +47,7 @@ static int omap2430_musb_init(struct musb *musb)
> > > u32 l;
> > > int status = 0;
> > > unsigned long int start;
> > > +
> > > struct omap_musb_board_data *data =
> > > (struct omap_musb_board_data *)musb->controller;
> > >
> > > @@ -129,3 +134,144 @@ const struct musb_platform_ops omap2430_ops =
> > > { .enable = omap2430_musb_enable,
> > > .disable = omap2430_musb_disable,
> > > };
> > > +
> > > +#if defined(CONFIG_DM_USB)
> > > +
> > > +struct omap2430_musb_platdata {
> > > + void *base;
> > > + void *ctrl_mod_base;
> > > + struct musb_hdrc_platform_data plat;
> > > + struct musb_hdrc_config musb_config;
> > > + struct omap_musb_board_data otg_board_data;
> > > +};
> > > +
> > > +static int omap2430_musb_ofdata_to_platdata(struct udevice *dev)
> > > +{
> > > + struct omap2430_musb_platdata *platdata =
> > > dev_get_platdata(dev);
> > > + const void *fdt = gd->fdt_blob;
> > > + int node = dev_of_offset(dev);
> > > +
> > > + platdata->base = (void *)dev_read_addr_ptr(dev);
> > > +
> > > + platdata->musb_config.multipoint = fdtdec_get_int(fdt, node,
> > > +
> > > "multipoint",
> > > + -1);
> > > + if (platdata->musb_config.multipoint < 0) {
> > > + pr_err("MUSB multipoint DT entry missing\n");
> > > + return -ENOENT;
> > > + }
> > > +
> > > + platdata->musb_config.dyn_fifo = 1;
> > > + platdata->musb_config.num_eps = fdtdec_get_int(fdt, node,
> > > + "num-eps",
> > > -1);
> > > + if (platdata->musb_config.num_eps < 0) {
> > > + pr_err("MUSB num-eps DT entry missing\n");
> > > + return -ENOENT;
> > > + }
> > > +
> > > + platdata->musb_config.ram_bits = fdtdec_get_int(fdt, node,
> > > + "ram-bits",
> > > -1);
> > > + if (platdata->musb_config.ram_bits < 0) {
> > > + pr_err("MUSB ram-bits DT entry missing\n");
> > > + return -ENOENT;
> > > + }
> > > +
> > > + platdata->plat.power = fdtdec_get_int(fdt, node,
> > > +
> > > "power", -1);
> > > + if (platdata->plat.power < 0) {
> > > + pr_err("MUSB power DT entry missing\n");
> > > + return -ENOENT;
> > > + }
> > > +
> > > + platdata->otg_board_data.interface_type =
> > > fdtdec_get_int(fdt, node,
> > > +
> > > "interface-type", -1);
> > > + if (platdata->otg_board_data.interface_type < 0) {
> > > + pr_err("MUSB interface-type DT entry missing\n");
> > > + return -ENOENT;
> > > + }
> > > +
> > > +#if 0 /* In a perfect world, mode would be set to OTG, mode 3 from
> > > DT */
> > > + platdata->plat.mode = fdtdec_get_int(fdt, node,
> > > +
> > > "mode", -1);
> > > + if (platdata->plat.mode < 0) {
> > > + pr_err("MUSB mode DT entry missing\n");
> > > + return -ENOENT;
> > > + }
> > > +#else /* MUSB_OTG, it doesn't work */
> > > +#ifdef CONFIG_USB_MUSB_HOST /* Host seems to be the only option
> > > that works */
> > > + platdata->plat.mode = MUSB_HOST;
> > > +#else /* For that matter, MUSB_PERIPHERAL doesn't either */
> > > + platdata->plat.mode = MUSB_PERIPHERAL;
> > > +#endif
> > > +#endif
> > > + platdata->otg_board_data.dev = dev;
> > > + platdata->plat.config = &platdata->musb_config;
> > > + platdata->plat.platform_ops = &omap2430_ops;
> > > + platdata->plat.board_data = &platdata->otg_board_data;
> > > + return 0;
> > > +}
> > > +
> > > +static int omap2430_musb_probe(struct udevice *dev)
> > > +{
> > > +#ifdef CONFIG_USB_MUSB_HOST
> > > + struct musb_host_data *host = dev_get_priv(dev);
> > > +#endif
> > > + struct omap2430_musb_platdata *platdata =
> > > dev_get_platdata(dev);
> > > + struct usb_bus_priv *priv = dev_get_uclass_priv(dev);
> > > + struct omap_musb_board_data *otg_board_data;
> > > + int ret;
> > > + void *base = dev_read_addr_ptr(dev);
> > > +
> > > + priv->desc_before_addr = true;
> > > +
> > > + otg_board_data = &platdata->otg_board_data;
> > > +
> > > +#ifdef CONFIG_USB_MUSB_HOST
> > > + host->host = musb_init_controller(&platdata->plat,
> > > + (struct device
> > > *)otg_board_data,
> > > + platdata->base);
> > > + if (!host->host) {
> > > + return -EIO;
> > > + }
> > > +
> > > + ret = musb_lowlevel_init(host);
> > > +#else
> > > + ret = musb_register(&platdata->plat,
> > > + (struct device *)otg_board_data,
> > > + platdata->base);
> > > +#endif
> > > + return ret;
> > > +}
> > > +
> > > +static int omap2430_musb_remove(struct udevice *dev)
> > > +{
> > > + struct musb_host_data *host = dev_get_priv(dev);
> > > +
> > > + musb_stop(host->host);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static const struct udevice_id omap2430_musb_ids[] = {
> > > + { .compatible = "ti,omap3-musb" },
> > > + { .compatible = "ti,omap4-musb" },
> > > + { }
> > > +};
> > > +
> > > +U_BOOT_DRIVER(omap2430_musb) = {
> > > + .name = "omap2430-musb",
> > > +#ifdef CONFIG_USB_MUSB_HOST
> > > + .id = UCLASS_USB,
> > > +#else
> > > + .id = UCLASS_USB_DEV_GENERIC,
> > > +#endif
> > > + .of_match = omap2430_musb_ids,
> > > + .ofdata_to_platdata = omap2430_musb_ofdata_to_platdata,
> > > + .probe = omap2430_musb_probe,
> > > + .remove = omap2430_musb_remove,
> > > + .ops = &musb_usb_ops,
> > > + .platdata_auto_alloc_size = sizeof(struct
> > > omap2430_musb_platdata),
> > > + .priv_auto_alloc_size = sizeof(struct musb_host_data),
> > > +};
> > > +
> > > +#endif /* CONFIG_DM_USB */
> > > --
> > > 2.17.1
> > >
>
>
>
>
> Best regards,
>
> Lukasz Majewski
>
> --
>
> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
More information about the U-Boot
mailing list