[U-Boot] [PATCH u-boot 1/2] ARM: dts: sync meson-gxbb-nanopi-k2 from Linux 4.17
Neil Armstrong
narmstrong at baylibre.com
Mon Jun 25 14:50:16 UTC 2018
Get the meson-gxbb-nanopi-k2.dts file from Linux 4.17.
Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/meson-gxbb-nanopi-k2.dts | 323 ++++++++++++++++++++++++++++++++++
2 files changed, 324 insertions(+)
create mode 100644 arch/arm/dts/meson-gxbb-nanopi-k2.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 493652e..bcbaae2 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -53,6 +53,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3399-puma-ddr1866.dtb \
rv1108-evb.dtb
dtb-$(CONFIG_ARCH_MESON) += \
+ meson-gxbb-nanopi-k2.dtb \
meson-gxbb-odroidc2.dtb \
meson-gxl-s905x-p212.dtb \
meson-gxl-s905x-libretech-cc.dtb \
diff --git a/arch/arm/dts/meson-gxbb-nanopi-k2.dts b/arch/arm/dts/meson-gxbb-nanopi-k2.dts
new file mode 100644
index 0000000..7d5709c
--- /dev/null
+++ b/arch/arm/dts/meson-gxbb-nanopi-k2.dts
@@ -0,0 +1,323 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Andreas Färber
+ */
+
+/dts-v1/;
+
+#include "meson-gxbb.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
+
+ aliases {
+ serial0 = &uart_AO;
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ stat {
+ label = "nanopi-k2:blue:stat";
+ gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ panic-indicator;
+ };
+ };
+
+ vdd_5v: regulator-vdd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vddio_ao18: regulator-vddio-ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddio_ao3v3: regulator-vddio-ao3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vddio_tf: regulator-vddio-tf {
+ compatible = "regulator-gpio";
+
+ regulator-name = "VDDIO_TF";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+
+ states = <3300000 0>,
+ <1800000 1>;
+
+ regulator-settling-time-up-us = <100>;
+ regulator-settling-time-down-us = <5000>;
+ };
+
+ wifi_32k: wifi-32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi_32k>;
+ clock-names = "ext_clock";
+ };
+
+ vcc1v8: regulator-vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vcc3v3: regulator-vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+};
+
+ðmac {
+ status = "okay";
+ pinctrl-0 = <ð_rgmii_pins>;
+ pinctrl-names = "default";
+
+ phy-handle = <ð_phy0>;
+ phy-mode = "rgmii";
+
+ amlogic,tx-delay-ns = <2>;
+
+ snps,reset-gpio = <&gpio GPIOZ_14 0>;
+ snps,reset-delays-us = <0 10000 1000000>;
+ snps,reset-active-low;
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ eth_phy0: ethernet-phy at 0 {
+ /* Realtek RTL8211F (0x001cc916) */
+ reg = <0>;
+ interrupt-parent = <&gpio_intc>;
+ /* MAC_INTR on GPIOZ_15 */
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&pinctrl_aobus {
+ gpio-line-names = "UART TX", "UART RX", "Power Control", "Power Key In",
+ "VCCK En", "CON1 Header Pin31",
+ "I2S Header Pin6", "IR In", "I2S Header Pin7",
+ "I2S Header Pin3", "I2S Header Pin4",
+ "I2S Header Pin5", "HDMI CEC", "SYS LED",
+ /* GPIO_TEST_N */
+ "";
+};
+
+&pinctrl_periphs {
+ gpio-line-names = /* Bank GPIOZ */
+ "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
+ "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
+ "Eth RX D3", "Eth RGMII TX Clk", "Eth TX En",
+ "Eth TX D0", "Eth TX D1", "Eth TX D2", "Eth TX D3",
+ "Eth PHY nRESET", "Eth PHY Intc",
+ /* Bank GPIOH */
+ "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL",
+ "CON1 Header Pin33",
+ /* Bank BOOT */
+ "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3", "eMMC D4",
+ "eMMC D5", "eMMC D6", "eMMC D7", "eMMC Clk",
+ "eMMC Reset", "eMMC CMD",
+ "", "", "", "", "eMMC DS",
+ "", "",
+ /* Bank CARD */
+ "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+ "SDCard D3", "SDCard D2", "SDCard Det",
+ /* Bank GPIODV */
+ "", "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "",
+ "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
+ "VDDEE Regulator", "VCCK Regulator",
+ /* Bank GPIOY */
+ "CON1 Header Pin7", "CON1 Header Pin11",
+ "CON1 Header Pin13", "CON1 Header Pin15",
+ "CON1 Header Pin18", "CON1 Header Pin19",
+ "CON1 Header Pin22", "CON1 Header Pin21",
+ "CON1 Header Pin24", "CON1 Header Pin23",
+ "CON1 Header Pin26", "CON1 Header Pin29",
+ "CON1 Header Pin32", "CON1 Header Pin8",
+ "CON1 Header Pin10", "CON1 Header Pin16",
+ "CON1 Header Pin12",
+ /* Bank GPIOX */
+ "WIFI SDIO D0", "WIFI SDIO D1", "WIFI SDIO D2",
+ "WIFI SDIO D3", "WIFI SDIO CLK", "WIFI SDIO CMD",
+ "WIFI Power Enable", "WIFI WAKE HOST",
+ "Bluetooth PCM DOUT", "Bluetooth PCM DIN",
+ "Bluetooth PCM SYNC", "Bluetooth PCM CLK",
+ "Bluetooth UART TX", "Bluetooth UART RX",
+ "Bluetooth UART CTS", "Bluetooth UART RTS",
+ "", "", "", "WIFI 32K", "Bluetooth Enable",
+ "Bluetooth WAKE HOST", "",
+ /* Bank GPIOCLK */
+ "", "CON1 Header Pin35", "", "";
+};
+
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao18>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>, <&sdio_irq_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <200000000>;
+
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddio_ao3v3>;
+ vqmmc-supply = <&vddio_ao18>;
+
+ brcmf: wifi at 1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+ };
+};
+
+/* SD */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+
+ vmmc-supply = <&vddio_ao3v3>;
+ vqmmc-supply = <&vddio_tf>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "disabled";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc3v3>;
+ vqmmc-supply = <&vcc1v8>;
+};
+
+/* DBG_UART */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+/* Bluetooth on AP6212 */
+&uart_A {
+ status = "disabled";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+};
+
+/* 40-pin CON1 */
+&uart_C {
+ status = "disabled";
+ pinctrl-0 = <&uart_c_pins>;
+ pinctrl-names = "default";
+};
+
+&usb0_phy {
+ status = "okay";
+ phy-supply = <&vdd_5v>;
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
--
2.7.4
More information about the U-Boot
mailing list