[U-Boot] [PATCH v2 12/58] keymile: Make distinct kmeter1, and kmcoge5ne configs

Mario Six mario.six at gdsys.cc
Mon Nov 5 14:44:26 UTC 2018


The kmeter1, and kmcoge5ne boards also build from the same config
file with #ifdef logic.

Create a separate include config for each board with the #ifdef logic
resolved as needed.

Signed-off-by: Mario Six <mario.six at gdsys.cc>

---

v1 -> v2:
* Combined config creation and simplification patches

---
 arch/powerpc/cpu/mpc83xx/Kconfig          |  11 +-
 board/keymile/km83xx/Kconfig              |  17 +-
 board/keymile/km83xx/km83xx.c             |   2 +-
 configs/kmcoge5ne_defconfig               |   3 +-
 configs/kmeter1_defconfig                 |   3 +-
 include/configs/{km8360.h => kmcoge5ne.h} |  29 --
 include/configs/kmeter1.h                 | 462 ++++++++++++++++++++++++++++++
 7 files changed, 489 insertions(+), 38 deletions(-)
 rename include/configs/{km8360.h => kmcoge5ne.h} (95%)
 create mode 100644 include/configs/kmeter1.h

diff --git a/arch/powerpc/cpu/mpc83xx/Kconfig b/arch/powerpc/cpu/mpc83xx/Kconfig
index 1ebb092f0bf..29d84f363d1 100644
--- a/arch/powerpc/cpu/mpc83xx/Kconfig
+++ b/arch/powerpc/cpu/mpc83xx/Kconfig
@@ -80,8 +80,15 @@ config TARGET_IDS8313
 	select DM
 	imply CMD_DM
 
-config TARGET_KM8360
-	bool "Support km8360"
+config TARGET_KMETER1
+	bool "Support kmeter1"
+	select ARCH_MPC8360
+	imply CMD_CRAMFS
+	imply CMD_DIAG
+	imply FS_CRAMFS
+
+config TARGET_KMCOGE5NE
+	bool "Support kmcoge5ne"
 	select ARCH_MPC8360
 	imply CMD_CRAMFS
 	imply CMD_DIAG
diff --git a/board/keymile/km83xx/Kconfig b/board/keymile/km83xx/Kconfig
index 0c4fa0b7fdb..fbbbb17034f 100644
--- a/board/keymile/km83xx/Kconfig
+++ b/board/keymile/km83xx/Kconfig
@@ -1,4 +1,4 @@
-if TARGET_KM8360
+if TARGET_KMETER1
 
 config SYS_BOARD
 	default "km83xx"
@@ -7,7 +7,20 @@ config SYS_VENDOR
 	default "keymile"
 
 config SYS_CONFIG_NAME
-	default "km8360"
+	default "kmeter1"
+
+endif
+
+if TARGET_KMCOGE5NE
+
+config SYS_BOARD
+	default "km83xx"
+
+config SYS_VENDOR
+	default "keymile"
+
+config SYS_CONFIG_NAME
+	default "kmcoge5ne"
 
 endif
 
diff --git a/board/keymile/km83xx/km83xx.c b/board/keymile/km83xx/km83xx.c
index 12044ee0d70..1fd6f919014 100644
--- a/board/keymile/km83xx/km83xx.c
+++ b/board/keymile/km83xx/km83xx.c
@@ -271,7 +271,7 @@ int last_stage_init(void)
 	}
 #endif
 
-#if defined(CONFIG_KMCOGE5NE)
+#if defined(CONFIG_TARGET_KMCOGE5NE)
 	struct bfticu_iomap *base =
 		(struct bfticu_iomap *)CONFIG_SYS_BFTIC3_BASE;
 	u8 dip_switch = in_8((u8 *)&(base->mswitch)) & BFTICU_DIPSWITCH_MASK;
diff --git a/configs/kmcoge5ne_defconfig b/configs/kmcoge5ne_defconfig
index 8a41d1ddc90..2a3f03f28e4 100644
--- a/configs/kmcoge5ne_defconfig
+++ b/configs/kmcoge5ne_defconfig
@@ -1,10 +1,9 @@
 CONFIG_PPC=y
 CONFIG_SYS_TEXT_BASE=0xF0000000
 CONFIG_MPC83xx=y
-CONFIG_TARGET_KM8360=y
+CONFIG_TARGET_KMCOGE5NE=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="KMCOGE5NE"
 CONFIG_MISC_INIT_R=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_BOARD_EARLY_INIT_R=y
diff --git a/configs/kmeter1_defconfig b/configs/kmeter1_defconfig
index 3f78854da78..3d37333c258 100644
--- a/configs/kmeter1_defconfig
+++ b/configs/kmeter1_defconfig
@@ -1,10 +1,9 @@
 CONFIG_PPC=y
 CONFIG_SYS_TEXT_BASE=0xF0000000
 CONFIG_MPC83xx=y
-CONFIG_TARGET_KM8360=y
+CONFIG_TARGET_KMETER1=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="KMETER1"
 CONFIG_MISC_INIT_R=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_BOARD_EARLY_INIT_R=y
diff --git a/include/configs/km8360.h b/include/configs/kmcoge5ne.h
similarity index 95%
rename from include/configs/km8360.h
rename to include/configs/kmcoge5ne.h
index 59fe2c216ee..6bf6b765d68 100644
--- a/include/configs/km8360.h
+++ b/include/configs/kmcoge5ne.h
@@ -12,11 +12,6 @@
 #define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
 #define CONFIG_SYS_KMBEC_FPGA_SIZE	64
 
-#if defined CONFIG_KMETER1
-#define CONFIG_HOSTNAME		"kmeter1"
-#define CONFIG_KM_BOARD_NAME   "kmeter1"
-#define CONFIG_KM_DEF_NETDEV	"netdev=eth2\0"
-#elif defined CONFIG_KMCOGE5NE
 #define CONFIG_HOSTNAME		"kmcoge5ne"
 #define CONFIG_KM_BOARD_NAME	"kmcoge5ne"
 #define CONFIG_KM_DEF_NETDEV	"netdev=eth1\0"
@@ -28,9 +23,6 @@
 
 #define CONFIG_KM_UBI_PARTITION_NAME_BOOT	"ubi0"
 #define CONFIG_KM_UBI_PARTITION_NAME_APP	"ubi1"
-#else
-#error ("Board not supported")
-#endif
 
 /*
  * High Level Configuration Options
@@ -169,10 +161,8 @@
 #define CONFIG_UEC_ETH
 #define CONFIG_ETHPRIME		"UEC0"
 
-#if !defined(CONFIG_ARCH_MPC8309)
 #define CONFIG_UEC_ETH1		/* GETH1 */
 #define UEC_VERBOSE_DEBUG	1
-#endif
 
 #ifdef CONFIG_UEC_ETH1
 #define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
@@ -361,7 +351,6 @@
 
 #define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
 
-#ifdef CONFIG_KMCOGE5NE
 /**
  * KMCOGE5NE has 512 MB RAM
  */
@@ -372,12 +361,6 @@
 	CSCONFIG_BANK_BIT_3 | \
 	CSCONFIG_ROW_BIT_13 | \
 	CSCONFIG_COL_BIT_10)
-#else
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
-					 CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10 | \
-					 CSCONFIG_ODT_WR_ONLY_CURRENT)
-#endif
 
 #define CONFIG_SYS_DDR_CLK_CNTL (\
 	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
@@ -457,7 +440,6 @@
 	OR_GPCM_TRLX | \
 	OR_GPCM_EAD)
 
-#ifdef CONFIG_KMCOGE5NE
 /*
  * BFTIC3 on the local bus CS4
  */
@@ -476,7 +458,6 @@
 	OR_GPCM_SCY_2 |\
 	OR_GPCM_TRLX |\
 	OR_GPCM_EAD)
-#endif
 
 /*
  * MMU Setup
@@ -502,7 +483,6 @@
 
 #define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
 
-#ifdef CONFIG_KMCOGE5NE
 /* BFTIC3:  icache cacheable, but dcache-inhibit and guarded */
 #define CONFIG_SYS_IBAT6L (\
 	CONFIG_SYS_BFTIC3_BASE | \
@@ -542,15 +522,6 @@
 #define CONFIG_TESTPIN_REG  gprt3	/* for kmcoge5ne */
 #define CONFIG_TESTPIN_MASK 0x20	/* for kmcoge5ne */
 
-#else
-#define CONFIG_SYS_IBAT6L	(0)
-#define CONFIG_SYS_IBAT6U	(0)
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
-#endif
-
 #define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
 #define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
 
diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h
new file mode 100644
index 00000000000..b4cadd3e0f6
--- /dev/null
+++ b/include/configs/kmeter1.h
@@ -0,0 +1,462 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2012
+ * Holger Brunck, Keymile GmbH Hannover, <holger.brunck at keymile.com>
+ * Christian Herzig, Keymile AG Switzerland, <christian.herzig at keymile.com>
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* KMBEC FPGA (PRIO) */
+#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE	64
+
+#define CONFIG_HOSTNAME		"kmeter1"
+#define CONFIG_KM_BOARD_NAME   "kmeter1"
+#define CONFIG_KM_DEF_NETDEV	"netdev=eth2\0"
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_QE			/* Has QE */
+
+/* include common defines/options for all Keymile boards */
+#include "km/keymile-common.h"
+#include "km/km-powerpc.h"
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN		66000000
+#define CONFIG_SYS_CLK_FREQ		66000000
+#define CONFIG_83XX_PCICLK		66000000
+
+/*
+ * IMMR new address
+ */
+#define CONFIG_SYS_IMMR		0xE0000000
+
+/*
+ * Bus Arbitration Configuration Register (ACR)
+ */
+#define CONFIG_SYS_ACR_PIPE_DEP 3       /* pipeline depth 4 transactions */
+#define CONFIG_SYS_ACR_RPTCNT   3       /* 4 consecutive transactions */
+#define CONFIG_SYS_ACR_APARK    0       /* park bus to master (below) */
+#define CONFIG_SYS_ACR_PARKM    3       /* parking master = QuiccEngine */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
+
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
+					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+
+#define CFG_83XX_DDR_USES_CS0
+
+/*
+ * Manually set up DDR parameters
+ */
+#define CONFIG_DDR_II
+#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_FLASH_BASE		0xF0000000
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+/* Reserve 768 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+						GENERATED_GBL_DATA_SIZE)
+
+/*
+ * Init Local Bus Memory Controller:
+ *
+ * Bank Bus     Machine PortSz  Size  Device
+ * ---- ---     ------- ------  -----  ------
+ *  0   Local   GPCM    16 bit  256MB FLASH
+ *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
+ *
+ */
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
+#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
+#define CONFIG_SYS_FLASH_PROTECTION
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_256MB)
+
+#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE | \
+				BR_PS_16 | /* 16 bit port size */ \
+				BR_MS_GPCM | /* MSEL = GPCM */ \
+				BR_V)
+
+#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \
+				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
+				OR_GPCM_SCY_5 | \
+				OR_GPCM_TRLX_SET | OR_GPCM_EAD)
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
+#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+
+/*
+ * PRIO1/PIGGY on the local bus CS1
+ */
+/* Window base at flash base */
+#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_KMBEC_FPGA_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_128MB)
+
+#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_KMBEC_FPGA_BASE | \
+				BR_PS_8 | /* 8 bit port size */ \
+				BR_MS_GPCM | /* MSEL = GPCM */ \
+				BR_V)
+#define CONFIG_SYS_OR1_PRELIM	(MEG_TO_AM(CONFIG_SYS_KMBEC_FPGA_SIZE) | \
+				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
+				OR_GPCM_SCY_2 | \
+				OR_GPCM_TRLX_SET | OR_GPCM_EAD)
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#define CONFIG_ETHPRIME		"UEC0"
+
+#define CONFIG_UEC_ETH1		/* GETH1 */
+#define UEC_VERBOSE_DEBUG	1
+
+#ifdef CONFIG_UEC_ETH1
+#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
+#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
+#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR	0
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
+#endif
+
+/*
+ * Environment
+ */
+
+#ifndef CONFIG_SYS_RAMBOOT
+#ifndef CONFIG_ENV_ADDR
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
+					CONFIG_SYS_MONITOR_LEN)
+#endif
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
+#ifndef CONFIG_ENV_OFFSET
+#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
+#endif
+
+/* Address and size of Redundant Environment Sector	*/
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
+						CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
+
+#else /* CFG_SYS_RAMBOOT */
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_SIZE		0x2000
+#endif /* CFG_SYS_RAMBOOT */
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_NUM_I2C_BUSES	4
+#define CONFIG_SYS_I2C_MAX_HOPS		1
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	200000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED	200000
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
+#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
+		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
+		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
+		{1, {I2C_NULL_HOP} } }
+
+#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
+
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_NAND_KMETER1
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
+#endif
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
+
+/*
+ * Core HID Setup
+ */
+#define CONFIG_SYS_HID0_INIT		0x000000000
+#define CONFIG_SYS_HID0_FINAL		(HID0_ENABLE_MACHINE_CHECK | \
+					 HID0_ENABLE_INSTRUCTION_CACHE)
+#define CONFIG_SYS_HID2			HID2_HBE
+
+/*
+ * MMU Setup
+ */
+
+#define CONFIG_HIGH_BATS	1	/* High BATs supported */
+
+/* DDR: cache cacheable */
+#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
+				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
+
+/* IMMRBAR & PCI IO: cache-inhibit and guarded */
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
+				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS \
+					| BATU_VP)
+#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
+
+/* PRIO1, PIGGY:  icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_KMBEC_FPGA_BASE | BATL_PP_RW | \
+				BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_KMBEC_FPGA_BASE | BATU_BL_128M | \
+				BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_KMBEC_FPGA_BASE | BATL_PP_RW | \
+				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
+					BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_FLASH_BASE | BATU_BL_256M | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
+				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
+#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
+
+/*
+ * Internal Definitions
+ */
+#define BOOTFLASH_START	0xF0000000
+
+#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
+#define CONFIG_KM_DEF_ENV "km-common=empty\0"
+#endif
+
+#ifndef CONFIG_KM_DEF_ARCH
+#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	CONFIG_KM_DEF_ENV						\
+	CONFIG_KM_DEF_ARCH						\
+	"newenv="							\
+		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
+		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
+	"unlock=yes\0"							\
+	""
+
+#if defined(CONFIG_UEC_ETH)
+#define CONFIG_HAS_ETH0
+#endif
+
+/*
+ * System IO Setup
+ */
+#define CONFIG_SYS_SICRH		(SICRH_UC1EOBI | SICRH_UC2E1OBI)
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+	HRCWL_CSB_TO_CLKIN_4X1 | \
+	HRCWL_CORE_TO_CSB_2X1 | \
+	HRCWL_CE_PLL_VCO_DIV_2 | \
+	HRCWL_CE_TO_PLL_1X6)
+
+#define CONFIG_SYS_HRCW_HIGH (\
+	HRCWH_CORE_ENABLE | \
+	HRCWH_FROM_0X00000100 | \
+	HRCWH_BOOTSEQ_DISABLE | \
+	HRCWH_SW_WATCHDOG_DISABLE | \
+	HRCWH_ROM_LOC_LOCAL_16BIT | \
+	HRCWH_BIG_ENDIAN | \
+	HRCWH_LALE_EARLY | \
+	HRCWH_LDP_CLEAR)
+
+/**
+ * DDR RAM settings
+ */
+#define CONFIG_SYS_DDR_SDRAM_CFG (\
+	SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+	SDRAM_CFG_SREN | \
+	SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
+
+#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
+					 CSCONFIG_ROW_BIT_13 | \
+					 CSCONFIG_COL_BIT_10 | \
+					 CSCONFIG_ODT_WR_ONLY_CURRENT)
+
+#define CONFIG_SYS_DDR_CLK_CNTL (\
+	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+
+#define CONFIG_SYS_DDR_INTERVAL (\
+	(0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+	(0x203 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_BNDS			0x0000007f
+
+#define CONFIG_SYS_DDRCDR (\
+	DDRCDR_EN | \
+	DDRCDR_Q_DRN)
+#define CONFIG_SYS_DDR_MODE		0x47860452
+#define CONFIG_SYS_DDR_MODE2		0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0 (\
+	(2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+	(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+	(6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+	(2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+	(0 << TIMING_CFG0_WWT_SHIFT) | \
+	(0 << TIMING_CFG0_RRT_SHIFT) | \
+	(0 << TIMING_CFG0_WRT_SHIFT) | \
+	(0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_50) | \
+				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
+				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
+				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+				 (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2 (\
+	(0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+	(3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+	(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+	(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+	(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+	(5 << TIMING_CFG2_CPO_SHIFT) | \
+	(0 << TIMING_CFG2_ADD_LAT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3			0x00000000
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
+#define CONFIG_SYS_LCRR_EADC		LCRR_EADC_2
+#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_4
+
+/*
+ * PAXE on the local bus CS3
+ */
+#define CONFIG_SYS_PAXE_BASE		0xA0000000
+#define CONFIG_SYS_PAXE_SIZE		256
+
+#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_PAXE_BASE
+
+#define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000001C /* 512MB window size */
+
+#define CONFIG_SYS_BR3_PRELIM (\
+	CONFIG_SYS_PAXE_BASE | \
+	(1 << BR_PS_SHIFT) | \
+	BR_V)
+
+#define CONFIG_SYS_OR3_PRELIM (\
+	MEG_TO_AM(CONFIG_SYS_PAXE_SIZE) | \
+	OR_GPCM_CSNT | \
+	OR_GPCM_ACS_DIV2 | \
+	OR_GPCM_SCY_2 | \
+	OR_GPCM_TRLX | \
+	OR_GPCM_EAD)
+
+/*
+ * MMU Setup
+ */
+
+/* PAXE:  icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT5L (\
+	CONFIG_SYS_PAXE_BASE | \
+	BATL_PP_10 | \
+	BATL_MEMCOHERENCE)
+
+#define CONFIG_SYS_IBAT5U (\
+	CONFIG_SYS_PAXE_BASE | \
+	BATU_BL_256M | \
+	BATU_VS | \
+	BATU_VP)
+
+#define CONFIG_SYS_DBAT5L (\
+	CONFIG_SYS_PAXE_BASE | \
+	BATL_PP_10 | \
+	BATL_CACHEINHIBIT | \
+	BATL_GUARDEDSTORAGE)
+
+#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_IBAT6L	(0)
+#define CONFIG_SYS_IBAT6U	(0)
+#define CONFIG_SYS_IBAT7L	(0)
+#define CONFIG_SYS_IBAT7U	(0)
+#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
+#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
+
+#endif /* CONFIG */
-- 
2.11.0



More information about the U-Boot mailing list