[U-Boot] [PATCH v2] sun8i: h3: Add support for the Beelink-x2 STB
codekipper at gmail.com
codekipper at gmail.com
Thu Nov 15 08:49:07 UTC 2018
From: Marcus Cooper <marcusc at axis.com>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.
Signed-off-by: Marcus Cooper <codekipper at gmail.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun8i-h3-beelink-x2.dts | 179 +++++++++++++++++++++++++++
board/sunxi/MAINTAINERS | 5 +
configs/beelink_x2_defconfig | 19 +++
4 files changed, 204 insertions(+)
create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts
create mode 100644 configs/beelink_x2_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 1cbb45d679..cc217d4f98 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -370,6 +370,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
sun8i-h2-plus-orangepi-r1.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
+ sun8i-h3-beelink-x2.dtb \
sun8i-h3-libretech-all-h3-cc.dtb \
sun8i-h3-nanopi-m1.dtb \
sun8i-h3-nanopi-m1-plus.dtb \
diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts b/arch/arm/dts/sun8i-h3-beelink-x2.dts
new file mode 100644
index 0000000000..683c5c31a9
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
@@ -0,0 +1,179 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Device Tree Source for Beelink X2
+//
+// Copyright (C) 2018 Marcus Cooper <codekipper at gmail.com>
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Beelink X2";
+ compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ ethernet1 = &sdiowifi;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "beelink-x2:blue:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ default-state = "on";
+ };
+
+ red {
+ label = "beelink-x2:red:standby";
+ gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+
+ sound_spdif {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "On-board SPDIF";
+
+ simple-audio-card,cpu {
+ sound-dai = <&spdif>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&spdif_out>;
+ };
+ };
+
+ spdif_out: spdif-out {
+ #sound-dai-cells = <0>;
+ compatible = "linux,spdif-dit";
+ };
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ /*
+ * Explicitly define the sdio device, so that we can add an ethernet
+ * alias for it (which e.g. makes u-boot set a mac-address).
+ */
+ sdiowifi: sdio_wifi at 1 {
+ reg = <1>;
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+®_usb0_vbus {
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spdif_tx_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ /* USB VBUS is always on except for the OTG port */
+ status = "okay";
+ usb0_id_det-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA07 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index 478e37285f..6417158fd1 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -159,6 +159,11 @@ M: Jagan Teki <jagan at amarulasolutions.com>
S: Maintained
F: configs/bananapi_m64_defconfig
+BEELINK X2 BOARD
+M: Marcus Cooper <codekipper at gmail.com>
+S: Maintained
+F: configs/beelink_x2_defconfig
+
COLOMBUS BOARD
M: Maxime Ripard <maxime.ripard at bootlin.com>
S: Maintained
diff --git a/configs/beelink_x2_defconfig b/configs/beelink_x2_defconfig
new file mode 100644
index 0000000000..6508e470a0
--- /dev/null
+++ b/configs/beelink_x2_defconfig
@@ -0,0 +1,19 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=624
+CONFIG_DRAM_ZQ=3881979
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-beelink-x2"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_CONSOLE_MUX=y
+CONFIG_SPL_I2C_SUPPORT=y
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_SUN8I_EMAC=y
+CONFIG_SY8106A_POWER=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
--
2.19.1
More information about the U-Boot
mailing list