[U-Boot] [U-Boot,v2,04/23] spl: Set up the bloblist in SPL

Simon Glass sjg at chromium.org
Fri Nov 16 00:29:06 UTC 2018


Hi Tom,

On 15 November 2018 at 16:10, Tom Rini <trini at konsulko.com> wrote:
> On Thu, Nov 15, 2018 at 04:07:59PM -0800, Simon Glass wrote:
>> Hi Tom,
>>
>> On 9 November 2018 at 10:43, Tom Rini <trini at konsulko.com> wrote:
>> > On Tue, Oct 02, 2018 at 05:22:34AM -0600, Simon Glass wrote:
>> >> The bloblist is normally set up in SPL ready for use by U-Boot. Add
>> >> a simple implementation of this to the common SPL code.
>> >>
>> >> Signed-off-by: Simon Glass <sjg at chromium.org>
>> >> ---
>> >>
>> >> Changes in v2: None
>> >>
>> >>  common/spl/spl.c | 18 ++++++++++++++++--
>> >>  include/spl.h    | 27 +++++++++++++++++++++++++++
>> >>  2 files changed, 43 insertions(+), 2 deletions(-)
>> >>
>> >> diff --git a/common/spl/spl.c b/common/spl/spl.c
>> >> index b917624e61d..2ca900ae9ed 100644
>> >> --- a/common/spl/spl.c
>> >> +++ b/common/spl/spl.c
>> >> @@ -7,6 +7,7 @@
>> >>   */
>> >>
>> >>  #include <common.h>
>> >> +#include <bloblist.h>
>> >>  #include <binman_sym.h>
>> >>  #include <dm.h>
>> >>  #include <spl.h>
>> >> @@ -345,6 +346,14 @@ static int spl_common_init(bool setup_malloc)
>> >>               return ret;
>> >>       }
>> >>  #endif
>> >> +     if (CONFIG_IS_ENABLED(BLOBLIST)) {
>> >> +             ret = bloblist_init();
>> >> +             if (ret) {
>> >> +                     debug("%s: Failed to set up bloblist: ret=%d\n",
>> >> +                           __func__, ret);
>> >> +                     return ret;
>> >> +             }
>> >> +     }
>> >>       if (CONFIG_IS_ENABLED(OF_CONTROL) && !CONFIG_IS_ENABLED(OF_PLATDATA)) {
>> >>               ret = fdtdec_setup();
>> >>               if (ret) {
>> >> @@ -483,6 +492,7 @@ void board_init_r(gd_t *dummy1, ulong dummy2)
>> >>               BOOT_DEVICE_NONE,
>> >>       };
>> >>       struct spl_image_info spl_image;
>> >> +     int ret;
>> >>
>> >>       debug(">>spl:board_init_r()\n");
>> >>
>> >> @@ -529,6 +539,12 @@ void board_init_r(gd_t *dummy1, ulong dummy2)
>> >>       }
>> >>
>> >>       spl_perform_fixups(&spl_image);
>> >> +     if (CONFIG_IS_ENABLED(BLOBLIST)) {
>> >> +             ret = bloblist_finish();
>> >> +             if (ret)
>> >> +                     printf("Warning: Failed to finish bloblist (ret=%d)\n",
>> >> +                            ret);
>> >> +     }
>> >>
>> >>  #ifdef CONFIG_CPU_V7M
>> >>       spl_image.entry_point |= 0x1;
>> >> @@ -558,8 +574,6 @@ void board_init_r(gd_t *dummy1, ulong dummy2)
>> >>             gd->malloc_ptr / 1024);
>> >>  #endif
>> >>  #ifdef CONFIG_BOOTSTAGE_STASH
>> >> -     int ret;
>> >> -
>> >>       bootstage_mark_name(BOOTSTAGE_ID_END_SPL, "end_spl");
>> >>       ret = bootstage_stash((void *)CONFIG_BOOTSTAGE_STASH_ADDR,
>> >>                             CONFIG_BOOTSTAGE_STASH_SIZE);
>> >
>> > I think we'll need a __maybe_unused on ret above for !BOOTSTAGE_STASH &&
>> > !BLOBLIST.
>> >
>>
>> The code for BLOBLIST uses if() rather than #if so it seems OK:
>>
>> if (CONFIG_IS_ENABLED(BLOBLIST)) {
>
> So long as it doesn't warn, OK :)

That's right. One of the benefits of if() is we can avoid #ifdefs
around local variables .

Regards,
Simon


More information about the U-Boot mailing list