[U-Boot] [PATCH] mmc: fsl_esdhc: Avoid infinite loop in esdhc_send_cmd_common()

[Baruch Siach]

Hi Fabio,

On Mon, Nov 19, 2018 at 09:15:24AM -0200, Fabio Estevam wrote:
> The following hang is observed on a Hummingboard 2 MicroSOM
> i2eX iMX6D - rev 1.3 with no eMMC populated on board:
> 
> U-Boot SPL 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)
> Trying to boot from MMC1
> 
> U-Boot 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)
> 
> CPU:   Freescale i.MX6D rev1.5 996 MHz (running at 792 MHz)
> CPU:   Extended Commercial temperature grade (-20C to 105C) at 33C
> Reset cause: POR
> Board: MX6 HummingBoard2
> DRAM:  1 GiB
> MMC:   FSL_SDHC: 0, FSL_SDHC: 1
> Loading Environment from MMC... *** Warning - bad CRC, using default environment
> 
> No panel detected: default to HDMI
> Display: HDMI (1024x768)
> In:    serial
> Out:   serial
> Err:   serial
> ---> hangs
> 
> which is caused by the following infinite loop inside esdhc_send_cmd_common()
> 
> 	while (!(esdhc_read32(&regs->irqstat) & flags))
> 		;
> 
> Instead of looping forever, provide an exit path so that a timeout
> error can be propagated in the case irqstat does not report
> any interrupts, which may happen when no eMMC is populated on
> board.
> 
> Reported-by: Ricardo Salveti <rsalveti at rsalveti.net>
> Signed-off-by: Fabio Estevam <festevam at gmail.com>
> ---
>  drivers/mmc/fsl_esdhc.c | 8 ++++++--
>  1 file changed, 6 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c
> index 3cdfa7f..7c17b79 100644
> --- a/drivers/mmc/fsl_esdhc.c
> +++ b/drivers/mmc/fsl_esdhc.c
> @@ -396,6 +396,7 @@ static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc,
>  	uint	irqstat;
>  	u32	flags = IRQSTAT_CC | IRQSTAT_CTOE;
>  	struct fsl_esdhc *regs = priv->esdhc_regs;
> +	unsigned long start;
>  
>  #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC111
>  	if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION)
> @@ -453,8 +454,11 @@ static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc,
>  		flags = IRQSTAT_BRR;
>  
>  	/* Wait for the command to complete */
> -	while (!(esdhc_read32(&regs->irqstat) & flags))
> -		;
> +	start = get_timer(0);
> +	while (!(esdhc_read32(&regs->irqstat) & flags)) {
> +		if (get_timer(start) > 1000)
> +			return -ETIMEDOUT;

Most other error paths in this routine do 'goto out' instead. The code under 
the 'out' label resets the module.

baruch

> +	}
>  
>  	irqstat = esdhc_read32(&regs->irqstat);

-- 
     http://baruch.siach.name/blog/                  ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch at tkos.co.il - tel: +972.2.679.5364, http://www.tkos.co.il -