[U-Boot] [PATCH 08/93] arm: Remove guruplug board
Simon Glass
sjg at chromium.org
Mon Nov 19 15:52:48 UTC 2018
This board has not been converted to CONFIG_DM_BLK by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg at chromium.org>
---
arch/arm/mach-kirkwood/Kconfig | 1 -
board/Marvell/guruplug/Kconfig | 12 ---
board/Marvell/guruplug/MAINTAINERS | 6 --
board/Marvell/guruplug/Makefile | 7 --
board/Marvell/guruplug/guruplug.c | 138 --------------------------
board/Marvell/guruplug/guruplug.h | 22 -----
board/Marvell/guruplug/kwbimage.cfg | 144 ----------------------------
configs/guruplug_defconfig | 43 ---------
include/configs/guruplug.h | 82 ----------------
9 files changed, 455 deletions(-)
delete mode 100644 board/Marvell/guruplug/Kconfig
delete mode 100644 board/Marvell/guruplug/MAINTAINERS
delete mode 100644 board/Marvell/guruplug/Makefile
delete mode 100644 board/Marvell/guruplug/guruplug.c
delete mode 100644 board/Marvell/guruplug/guruplug.h
delete mode 100644 board/Marvell/guruplug/kwbimage.cfg
delete mode 100644 configs/guruplug_defconfig
delete mode 100644 include/configs/guruplug.h
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index 3b860c4f55f..00ed62591ea 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -73,7 +73,6 @@ config SYS_SOC
source "board/Marvell/openrd/Kconfig"
source "board/Marvell/dreamplug/Kconfig"
source "board/Synology/ds109/Kconfig"
-source "board/Marvell/guruplug/Kconfig"
source "board/Marvell/sheevaplug/Kconfig"
source "board/buffalo/lsxl/Kconfig"
source "board/cloudengines/pogo_e02/Kconfig"
diff --git a/board/Marvell/guruplug/Kconfig b/board/Marvell/guruplug/Kconfig
deleted file mode 100644
index 529e6e3b4ba..00000000000
--- a/board/Marvell/guruplug/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_GURUPLUG
-
-config SYS_BOARD
- default "guruplug"
-
-config SYS_VENDOR
- default "Marvell"
-
-config SYS_CONFIG_NAME
- default "guruplug"
-
-endif
diff --git a/board/Marvell/guruplug/MAINTAINERS b/board/Marvell/guruplug/MAINTAINERS
deleted file mode 100644
index b5d07348316..00000000000
--- a/board/Marvell/guruplug/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-GURUPLUG BOARD
-M: Siddarth Gore <gores at marvell.com>
-S: Maintained
-F: board/Marvell/guruplug/
-F: include/configs/guruplug.h
-F: configs/guruplug_defconfig
diff --git a/board/Marvell/guruplug/Makefile b/board/Marvell/guruplug/Makefile
deleted file mode 100644
index b0dfc0cd6d9..00000000000
--- a/board/Marvell/guruplug/Makefile
+++ /dev/null
@@ -1,7 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Siddarth Gore <gores at marvell.com>
-
-obj-y := guruplug.o
diff --git a/board/Marvell/guruplug/guruplug.c b/board/Marvell/guruplug/guruplug.c
deleted file mode 100644
index 466f85eb081..00000000000
--- a/board/Marvell/guruplug/guruplug.c
+++ /dev/null
@@ -1,138 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Siddarth Gore <gores at marvell.com>
- */
-
-#include <common.h>
-#include <miiphy.h>
-#include <asm/mach-types.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include "guruplug.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
- /*
- * default gpio configuration
- * There are maximum 64 gpios controlled through 2 sets of registers
- * the below configuration configures mainly initial LED status
- */
- mvebu_config_gpio(GURUPLUG_OE_VAL_LOW,
- GURUPLUG_OE_VAL_HIGH,
- GURUPLUG_OE_LOW, GURUPLUG_OE_HIGH);
-
- /* Multi-Purpose Pins Functionality configuration */
- static const u32 kwmpp_config[] = {
- MPP0_NF_IO2,
- MPP1_NF_IO3,
- MPP2_NF_IO4,
- MPP3_NF_IO5,
- MPP4_NF_IO6,
- MPP5_NF_IO7,
- MPP6_SYSRST_OUTn,
- MPP7_GPO, /* GPIO_RST */
- MPP8_TW_SDA,
- MPP9_TW_SCK,
- MPP10_UART0_TXD,
- MPP11_UART0_RXD,
- MPP12_SD_CLK,
- MPP13_SD_CMD,
- MPP14_SD_D0,
- MPP15_SD_D1,
- MPP16_SD_D2,
- MPP17_SD_D3,
- MPP18_NF_IO0,
- MPP19_NF_IO1,
- MPP20_GE1_0,
- MPP21_GE1_1,
- MPP22_GE1_2,
- MPP23_GE1_3,
- MPP24_GE1_4,
- MPP25_GE1_5,
- MPP26_GE1_6,
- MPP27_GE1_7,
- MPP28_GE1_8,
- MPP29_GE1_9,
- MPP30_GE1_10,
- MPP31_GE1_11,
- MPP32_GE1_12,
- MPP33_GE1_13,
- MPP34_GE1_14,
- MPP35_GE1_15,
- MPP36_GPIO,
- MPP37_GPIO,
- MPP38_GPIO,
- MPP39_GPIO,
- MPP40_TDM_SPI_SCK,
- MPP41_TDM_SPI_MISO,
- MPP42_TDM_SPI_MOSI,
- MPP43_GPIO,
- MPP44_GPIO,
- MPP45_GPIO,
- MPP46_GPIO, /* M_RLED */
- MPP47_GPIO, /* M_GLED */
- MPP48_GPIO, /* B_RLED */
- MPP49_GPIO, /* B_GLED */
- 0
- };
- kirkwood_mpp_conf(kwmpp_config, NULL);
- return 0;
-}
-
-int board_init(void)
-{
- /*
- * arch number of board
- */
- gd->bd->bi_arch_number = MACH_TYPE_GURUPLUG;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
-
- return 0;
-}
-
-#ifdef CONFIG_RESET_PHY_R
-void mv_phy_88e1121_init(char *name)
-{
- u16 reg;
- u16 devadr;
-
- if (miiphy_set_current_dev(name))
- return;
-
- /* command to read PHY dev address */
- if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
- printf("Err..%s could not read PHY dev address\n",
- __FUNCTION__);
- return;
- }
-
- /*
- * Enable RGMII delay on Tx and Rx for CPU port
- * Ref: sec 4.7.2 of chip datasheet
- */
- miiphy_write(name, devadr, MV88E1121_PGADR_REG, 2);
- miiphy_read(name, devadr, MV88E1121_MAC_CTRL2_REG, ®);
- reg |= (MV88E1121_RGMII_RXTM_CTRL | MV88E1121_RGMII_TXTM_CTRL);
- miiphy_write(name, devadr, MV88E1121_MAC_CTRL2_REG, reg);
- miiphy_write(name, devadr, MV88E1121_PGADR_REG, 0);
-
- /* reset the phy */
- miiphy_reset(name, devadr);
-
- printf("88E1121 Initialized on %s\n", name);
-}
-
-void reset_phy(void)
-{
- /* configure and initialize both PHY's */
- mv_phy_88e1121_init("egiga0");
- mv_phy_88e1121_init("egiga1");
-}
-#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/guruplug/guruplug.h b/board/Marvell/guruplug/guruplug.h
deleted file mode 100644
index a7023668132..00000000000
--- a/board/Marvell/guruplug/guruplug.h
+++ /dev/null
@@ -1,22 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Siddarth Gore <gores at marvell.com>
- */
-
-#ifndef __GURUPLUG_H
-#define __GURUPLUG_H
-
-#define GURUPLUG_OE_LOW (~(0))
-#define GURUPLUG_OE_HIGH (~(0))
-#define GURUPLUG_OE_VAL_LOW 0
-#define GURUPLUG_OE_VAL_HIGH (0xf << 16) /* 4 LED Pins high */
-
-/* PHY related */
-#define MV88E1121_MAC_CTRL2_REG 21
-#define MV88E1121_PGADR_REG 22
-#define MV88E1121_RGMII_TXTM_CTRL (1 << 4)
-#define MV88E1121_RGMII_RXTM_CTRL (1 << 5)
-
-#endif /* __GURUPLUG_H */
diff --git a/board/Marvell/guruplug/kwbimage.cfg b/board/Marvell/guruplug/kwbimage.cfg
deleted file mode 100644
index 8a0d752c91c..00000000000
--- a/board/Marvell/guruplug/kwbimage.cfg
+++ /dev/null
@@ -1,144 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Siddarth Gore <gores at marvell.com>
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM nand
-NAND_ECC_MODE default
-NAND_PAGE_SIZE 0x0800
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0/1 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1b1b9b9b
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000c30 # DDR Configuration register
-# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
-# bit 4: 0=addr/cmd in smame cycle
-# bit 5: 0=clk is driven during self refresh, we don't care for APX
-# bit 6: 0=use recommended falling edge of clk for addr/cmd
-# bit14: 0=input buffer always powered up
-# bit18: 1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31: 0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
-# bit3-0: TRAS lsbs
-# bit7-4: TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20: TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
-# bit6-0: TRFC
-# bit8-7: TR2R
-# bit10-9: TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x000000cc # DDR Address Control
-# bit1-0: 01, Cs0width=x8
-# bit3-2: 10, Cs0size=1Gb
-# bit5-4: 01, Cs1width=x8
-# bit7-6: 10, Cs1size=1Gb
-# bit9-8: 00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16: 0, Cs0AddrSel
-# bit17: 0, Cs1AddrSel
-# bit18: 0, Cs2AddrSel
-# bit19: 0, Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
-# bit0: 0, OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000 # DDR Operation
-# bit3-0: 0x0, DDR cmd
-# bit31-4: 0 required
-
-DATA 0xFFD0141C 0x00000C52 # DDR Mode
-# bit2-0: 2, BurstLen=2 required
-# bit3: 0, BurstType=0 required
-# bit6-4: 4, CL=5
-# bit7: 0, TestMode=0 normal
-# bit8: 0, DLL reset=0 normal
-# bit11-9: 6, auto-precharge write recovery ????????????
-# bit12: 0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000040 # DDR Extended Mode
-# bit0: 0, DDR DLL enabled
-# bit1: 0, DDR drive strenght normal
-# bit2: 0, DDR ODT control lsd (disabled)
-# bit5-3: 000, required
-# bit6: 1, DDR ODT control msb, (disabled)
-# bit9-7: 000, required
-# bit10: 0, differential DQS enabled
-# bit11: 0, required
-# bit12: 0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
-# bit2-0: 111, required
-# bit3 : 1 , MBUS Burst Chop disabled
-# bit6-4: 111, required
-# bit7 : 0
-# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9 : 0 , no half clock cycle addition to dataout
-# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0 required
-
-DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
-# bit0: 1, Window enabled
-# bit1: 0, Write Protect disabled
-# bit3-2: 00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x0F, Size (i.e. 256MB)
-
-DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
-DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
-
-DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low)
-DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
-# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
-# bit3-2: 01, ODT1 active NEVER!
-# bit31-4: zero, required
-
-DATA 0xFFD0149C 0x0000E803 # CPU ODT Control
-DATA 0xFFD01480 0x00000001 # DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
diff --git a/configs/guruplug_defconfig b/configs/guruplug_defconfig
deleted file mode 100644
index 9998e48ab9c..00000000000
--- a/configs/guruplug_defconfig
+++ /dev/null
@@ -1,43 +0,0 @@
-CONFIG_ARM=y
-CONFIG_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_TARGET_GURUPLUG=y
-CONFIG_IDENT_STRING="\nMarvell-GuruPlug"
-CONFIG_NR_DRAM_BANKS=2
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_BOOTDELAY=3
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_IDE=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_JFFS2=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:896K(uboot),128K(uboot_env),- at 1M(root)"
-CONFIG_CMD_UBI=y
-CONFIG_ISO_PARTITION=y
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="kirkwood-guruplug-server-plus"
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_DM=y
-CONFIG_MVSATA_IDE=y
-# CONFIG_MMC is not set
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_DM_RTC=y
-CONFIG_RTC_MV=y
-CONFIG_SYS_NS16550=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_LZMA=y
diff --git a/include/configs/guruplug.h b/include/configs/guruplug.h
deleted file mode 100644
index 739ab320f63..00000000000
--- a/include/configs/guruplug.h
+++ /dev/null
@@ -1,82 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009-2014
- * Gerald Kerma <dreagle at doukki.net>
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Siddarth Gore <gores at marvell.com>
- */
-
-#ifndef _CONFIG_GURUPLUG_H
-#define _CONFIG_GURUPLUG_H
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */
-
-/*
- * Standard filesystems
- */
-#define CONFIG_BZIP2
-
-/*
- * mv-plug-common.h should be defined after CMD configs since it used them
- * to enable certain macros
- */
-#include "mv-plug-common.h"
-
-/*
- * Environment variables configurations
- */
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
-#endif
-/*
- * max 4k env size is enough, but in case of nand
- * it has to be rounded to sector size
- */
-#define CONFIG_ENV_SIZE 0x20000 /* 128k */
-#define CONFIG_ENV_OFFSET 0xE0000 /* env starts here */
-/*
- * Environment is right behind U-Boot in flash. Make sure U-Boot
- * doesn't grow into the environment area.
- */
-#define CONFIG_BOARD_SIZE_LIMIT CONFIG_ENV_OFFSET
-
-/*
- * Default environment variables
- */
-#define CONFIG_BOOTCOMMAND \
- "setenv bootargs ${console} ${mtdparts} ${bootargs_root}; " \
- "ubi part root; " \
- "ubifsmount ubi:rootfs; " \
- "ubifsload 0x800000 ${kernel}; " \
- "ubifsload 0x700000 ${fdt}; " \
- "ubifsumount; " \
- "fdt addr 0x700000; fdt resize; fdt chosen; " \
- "bootz 0x800000 - 0x700000"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "console=console=ttyS0,115200\0" \
- "mtdids=nand0=orion_nand\0" \
- "mtdparts="CONFIG_MTDPARTS_DEFAULT \
- "kernel=/boot/zImage\0" \
- "fdt=/boot/guruplug-server-plus.dtb\0" \
- "bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw\0"
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */
-#define CONFIG_PHY_BASE_ADR 0
-#endif /* CONFIG_CMD_NET */
-
-/*
- * SATA Driver configuration
- */
-#ifdef CONFIG_MVSATA_IDE
-#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
-#endif /*CONFIG_MVSATA_IDE*/
-
-#endif /* _CONFIG_GURUPLUG_H */
--
2.19.1.1215.g8438c0b245-goog
More information about the U-Boot
mailing list