[U-Boot] [PATCH] imx: Add PHYTEC phyBOARD-i.MX6UL-Segin
Martyn Welch
martyn.welch at collabora.com
Mon Nov 19 17:23:31 UTC 2018
On Thu, 2018-11-15 at 01:25 +0100, Lukasz Majewski wrote:
> Hi Martyn,
>
> > Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer.
> > Based on the PHYTEC phyCORE-i.MX6UL SOM (PCL063). This port
> > provides
> > both SPL and DCD based boot options (hence the two defconfigs).
> >
> > CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
> > CPU: Industrial temperature grade (-40C to 105C) at 44C
> > Reset cause: POR
> > Board: PHYTEC phyCORE-i.MX6UL
> > I2C: ready
> > DRAM: 256 MiB
> > NAND: 512 MiB
> > MMC: FSL_SDHC: 0
> > In: serial
> > Out: serial
> > Err: serial
> > Net: FEC0
> >
> > Working:
> > - Eth0
> > - Eth1
> > - i2C
> > - MMC/SD
> > - NAND
> > - UART (1 & 5)
> > - USB (host & otg)
>
> Could you double check if maybe you could use Driver Model versions
> of
> some drivers? To be more specific - the ETH interfaces, I2C, eMMC,
> etc.
>
Hi Lukasz,
I've so far managed to get SD card, i2c and USB working via the driver
model, though I'm stuggling to get the Eth interfaces working - the
driver model probe doesn't seem to get the PHY addresses from the
device tree and I suspect it's also not able to pick up that both phys
are on the same MDIO bus form it either. Is this support still work in
progress?
Martyn
> > Signed-off-by: Martyn Welch <martyn.welch at collabora.com>
> >
> > ---
> >
> > arch/arm/mach-imx/mx6/Kconfig | 8 +
> > board/phytec/pcl063/Kconfig | 12 +
> > board/phytec/pcl063/MAINTAINERS | 7 +
> > board/phytec/pcl063/Makefile | 7 +
> > board/phytec/pcl063/README | 43 +++
> > board/phytec/pcl063/imximage.cfg | 177 +++++++++++++
> > board/phytec/pcl063/pcl063.c | 379
> > +++++++++++++++++++++++++++ board/phytec/pcl063/spl.c |
> > 118 +++++++++ configs/phycore_pcl063_defconfig | 47 ++++
> > configs/phycore_pcl063_spl_defconfig | 55 ++++
> > include/configs/pcl063.h | 107 ++++++++
> > 11 files changed, 960 insertions(+)
> > create mode 100644 board/phytec/pcl063/Kconfig
> > create mode 100644 board/phytec/pcl063/MAINTAINERS
> > create mode 100644 board/phytec/pcl063/Makefile
> > create mode 100644 board/phytec/pcl063/README
> > create mode 100644 board/phytec/pcl063/imximage.cfg
> > create mode 100644 board/phytec/pcl063/pcl063.c
> > create mode 100644 board/phytec/pcl063/spl.c
> > create mode 100644 configs/phycore_pcl063_defconfig
> > create mode 100644 configs/phycore_pcl063_spl_defconfig
> > create mode 100644 include/configs/pcl063.h
> >
> > diff --git a/arch/arm/mach-imx/mx6/Kconfig
> > b/arch/arm/mach-imx/mx6/Kconfig index 06c25bae36..22aea99f8f 100644
> > --- a/arch/arm/mach-imx/mx6/Kconfig
> > +++ b/arch/arm/mach-imx/mx6/Kconfig
> > @@ -428,6 +428,13 @@ config TARGET_PFLA02
> > select MX6QDL
> > select SUPPORT_SPL
> >
> > +config TARGET_PCL063
> > + bool "PHYTEC PCL063 (phyCORE-i.MX6UL)"
> > + select MX6UL
> > + select DM
> > + select DM_THERMAL
> > + select SUPPORT_SPL
>
> Your board is only selecting DM_THERMAL.
>
> One good way to check the list of DM aware (used) blocks is to run
> "dm
> list"
>
> > +
> > config TARGET_SECOMX6
> > bool "secomx6 boards"
> >
> > @@ -550,6 +557,7 @@ source "board/freescale/mx6ullevk/Kconfig"
> > source "board/grinn/liteboard/Kconfig"
> > source "board/phytec/pcm058/Kconfig"
> > source "board/phytec/pfla02/Kconfig"
> > +source "board/phytec/pcl063/Kconfig"
> > source "board/gateworks/gw_ventana/Kconfig"
> > source "board/kosagi/novena/Kconfig"
> > source "board/samtec/vining_2000/Kconfig"
> > diff --git a/board/phytec/pcl063/Kconfig
> > b/board/phytec/pcl063/Kconfig
> > new file mode 100644
> > index 0000000000..977db70f64
> > --- /dev/null
> > +++ b/board/phytec/pcl063/Kconfig
> > @@ -0,0 +1,12 @@
> > +if TARGET_PCL063
> > +
> > +config SYS_BOARD
> > + default "pcl063"
> > +
> > +config SYS_VENDOR
> > + default "phytec"
> > +
> > +config SYS_CONFIG_NAME
> > + default "pcl063"
> > +
> > +endif
> > diff --git a/board/phytec/pcl063/MAINTAINERS
> > b/board/phytec/pcl063/MAINTAINERS new file mode 100644
> > index 0000000000..8edc45827c
> > --- /dev/null
> > +++ b/board/phytec/pcl063/MAINTAINERS
> > @@ -0,0 +1,7 @@
> > +PCL063 BOARD
> > +M: Martyn Welch <martyn.welch at collabora.com>
> > +S: Maintained
> > +F: board/phytec/pcl063/
> > +F: configs/phycore_pcl063_defconfig
> > +F: configs/phycore_pcl063_spl_defconfig
> > +F: include/configs/pcl063.h
> > diff --git a/board/phytec/pcl063/Makefile
> > b/board/phytec/pcl063/Makefile new file mode 100644
> > index 0000000000..53c73c9b08
> > --- /dev/null
> > +++ b/board/phytec/pcl063/Makefile
> > @@ -0,0 +1,7 @@
> > +# Copyright (C) 2018 Collabora Ltd.
> > +#
> > +# SPDX-License-Identifier: GPL-2.0+
> > +#
> > +
> > +obj-y := pcl063.o
> > +obj-$(CONFIG_SPL_BUILD) += spl.o
> > diff --git a/board/phytec/pcl063/README
> > b/board/phytec/pcl063/README
> > new file mode 100644
> > index 0000000000..d73e90e83d
> > --- /dev/null
> > +++ b/board/phytec/pcl063/README
> > @@ -0,0 +1,43 @@
> > +How to use U-Boot on PHYTEC phyBOARD-i.MX6UL-Segin
> > +--------------------------------------------------
> > +
> > +- Clean U-Boot tree:
> > +
> > + $ make mrproper
> > +
> > +- Configure U-Boot for phyCORE-i.MX6UL (using DCD):
> > +
> > + $ make phycore_pcl063_defconfig
> > +
> > + Or for build with SPL:
> > +
> > + $ make phycore_pcl063_spl_defconfig
> > +
> > +- Build U-Boot
> > +
> > + $ make
> > +
> > + This will either generate an u-boot.imx image or SPL and
> > u-boot-dtb.img
> > + images depending on the config chosen.
> > +
> > +- When an u-boot.imx image has been built, flash this into a micro
> > SD card as
> > + follows:
> > +
> > + $ sudo dd if=u-boot.imx of=/dev/mmcblk0 bs=1k seek=1; sync
> > +
> > +- If the SPL and u-boot-dtb.img image have been built both need to
> > be flashed
> > + into the micro SD card:
> > +
> > + $ sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
> > + $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69;
> > sync
> > +
> > +- Jumper settings:
> > +
> > + JP1: Open: Boot from NAND
> > + Closed: Boot from SD/MMC1
> > +
> > +- Connect the Serial cable to UART0 and the PC for the console.
> > +
> > +- Insert the micro SD card in the board and power it up.
> > +
> > +- U-Boot messages should come up.
> > diff --git a/board/phytec/pcl063/imximage.cfg
> > b/board/phytec/pcl063/imximage.cfg new file mode 100644
> > index 0000000000..a50aaa4711
> > --- /dev/null
> > +++ b/board/phytec/pcl063/imximage.cfg
> > @@ -0,0 +1,177 @@
> > +/*
> > + * Copyright (C) 2018 Collabora Ltd.
> > + *
> > + * Values taken from: Barebox:
> > + * - arch/arm/boards/phytec-som-imx6/flash-header-phytec-
> > pcl063.h
> > + * -
> > arch/arm/boards/phytec-som-imx6/flash-header-phytec-pcl063-
> > 256mb.imxcfg
> > + *
> > + * Based on board/ccv/xpress/imximage.cfg:
> > + * Copyright (C) 2015-2016 Stefan Roese <sr at denx.de>
> > + *
> > + * SPDX-License-Identifier: GPL-2.0+
> > + */
> > +
> > +#define __ASSEMBLY__
> > +#include <config.h>
> > +
> > +IMAGE_VERSION 2
> > +
> > +/*
> > + * Boot Device : one of
> > + * sd, nand
> > + */
> > +BOOT_FROM sd
> > +
> > +/*
> > + * Device Configuration Data (DCD)
> > + *
> > + * Each entry must have the format:
> > + * Addr-type Address Value
> > + *
> > + * where:
> > + * Addr-type register length (1,2 or 4 bytes)
> > + * Address absolute address of the register
> > + * value value to be stored in the register
> > + */
> > +
> > +/* Enable all clocks */
> > +DATA 4 0x020c4068 0xffffffff
> > +DATA 4 0x020c406c 0xffffffff
> > +DATA 4 0x020c4070 0xffffffff
> > +DATA 4 0x020c4074 0xffffffff
> > +DATA 4 0x020c4078 0xffffffff
> > +DATA 4 0x020c407c 0xffffffff
> > +DATA 4 0x020c4080 0xffffffff
> > +
> > +/* ddr io type */
> > +DATA 4 0x020e04b4 0x000C0000 /* IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE */
> > +DATA 4 0x020e04ac 0x00000000 /* IOMUXC_SW_PAD_CTL_GRP_DDRPKE */
> > +
> > +/* clock */
> > +DATA 4 0x020e027c 0x00000030 /*
> > IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK0_P
> > */ +
> > +/* control and address */
> > +DATA 4 0x020E024C 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RAS */
> > +DATA 4 0x020E0250 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_CAS */
> > +DATA 4 0x020E0490 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_ADDDS */
> > +DATA 4 0x020E0288 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RESET
> > */
> > +DATA 4 0x020E0270 0x00000000 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDBA2 -
> > DSE can be
> > + configured using Group Control
> > Register:
> > + IOMUXC_SW_PAD_CTL_GRP_CTLDS */
> > +DATA 4 0x020E0260 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT0 */
> > +DATA 4 0x020E0264 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT1 */
> > +DATA 4 0x020E04A0 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_CTLDS */
> > +
> > +/* data strobes */
> > +DATA 4 0x020e0494 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL
> > */
> > +DATA 4 0x020e0280 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0_P
> > */
> > +DATA 4 0x020e0284 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1_P
> > */
> > +
> > +/* data */
> > +DATA 4 0x020E04B0 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE */
> > +DATA 4 0x020E0498 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B0DS */
> > +DATA 4 0x020E04A4 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B1DS */
> > +DATA 4 0x020E0244 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM0 */
> > +DATA 4 0x020E0248 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM1 */
> > +
> > +/*
> > + * DDR Controller Registers
> > + *
> > + * Manufacturer: Micron
> > + * Device Part Number: MT41K256M16TW-107 IT:P
> > + * Clock Freq.: 933MHz
> > + * Density per CS in Gb: 1
> > + * Chip Selects used: 1
> > + * Number of Banks: 8
> > + * Row address: 15
> > + * Column address: 10
> > + * Data bus width 16
> > + */
> > +DATA 4 0x021b001c 0x00008000 /* MMDC0_MDSCR, set the Configuration
> > request bit
> > + during MMDC set up */
> > +
> > +/*
> > + * Calibration setup
> > + */
> > +DATA 4 0x021b0800 0xA1390003 /* DDR_PHY_P0_MPZQHWCTRL, enable both
> > one-time &
> > + periodic HW ZQ calibration. */
> > +
> > +/*
> > + * For target board, may need to run write leveling calibration to
> > fine tune
> > + * these settings.
> > + */
> > +DATA 4 0x021b080c 0x00000000
> > +
> > +/* Read DQS Gating calibration */
> > +DATA 4 0x021b083c 0x41480148 /* MPDGCTRL0 PHY0 */
> > +
> > +/* Read calibration */
> > +DATA 4 0x021b0848 0x40403E42 /* MPRDDLCTL PHY0 */
> > +
> > +/* Write calibration */
> > +DATA 4 0x021b0850 0x40405852 /* MPWRDLCTL PHY0 */
> > +
> > +/*
> > + * read data bit delay: (3 is the reccommended default value,
> > although out of
> > + * reset value is 0)
> > + */
> > +DATA 4 0x021b081c 0x33333333 /* DDR_PHY_P0_MPREDQBY0DL3 */
> > +DATA 4 0x021b0820 0x33333333 /* DDR_PHY_P0_MPREDQBY1DL3 */
> > +DATA 4 0x021b082c 0xF3333333
> > +DATA 4 0x021b0830 0xF3333333
> > +
> > +DATA 4 0x021b08c0 0x00922012
> > +
> > +/* Clock Fine Tuning */
> > +DATA 4 0x021B0858 0x00000F00 /* [MMDC_MPSDCTRL] MMDC PHY CK
> > Control
> > Register */ +
> > +/* Complete calibration by forced measurement: */
> > +DATA 4 0x021b08b8 0x00000800 /* DDR_PHY_P0_MPMUR0, frc_msr */
> > +/*
> > + * Calibration setup end
> > + */
> > +
> > +/* MMDC init: */
> > +DATA 4 0x021b0004 0x0002002D /* MMDC0_MDPDC */
> > +DATA 4 0x021b0008 0x1B333030 /* MMDC0_MDOTC */
> > +DATA 4 0x021b000c 0x676B52F3 /* MMDC0_MDCFG0 */
> > +DATA 4 0x021b0010 0xB66D0B63 /* MMDC0_MDCFG1 */
> > +DATA 4 0x021b0014 0x01FF00DB /* MMDC0_MDCFG2 */
> > +
> > +/*
> > + * MDMISC: RALAT kept to the high level of 5.
> > + * MDMISC: consider reducing RALAT if your 528MHz board design
> > allow
> > that.
> > + * Lower RALAT benefits:
> > + * a. better operation at low frequency, for LPDDR2 freq < 100MHz,
> > change RALAT
> > + * to 3
> > + * b. Small performence improvment
> > + */
> > +DATA 4 0x021b0018 0x00211740 /* MMDC0_MDMISC */
> > +
> > +DATA 4 0x021b001c 0x00008000 /* MMDC0_MDSCR, set the Configuration
> > request bit
> > + during MMDC set up */
> > +
> > +DATA 4 0x021b002c 0x000026D2 /* MMDC0_MDRWD */
> > +DATA 4 0x021b0030 0x006B1023 /* MMDC0_MDOR */
> > +DATA 4 0x021b0040 0x00000047 /* Chan0 CS0_END */
> > +DATA 4 0x021b0000 0x83180000 /* MMDC0_MDCTL */
> > +
> > +/* Mode register writes */
> > +DATA 4 0x021b001c 0x02008032 /* MMDC0_MDSCR, MR2 write, CS0 */
> > +DATA 4 0x021b001c 0x00008033 /* MMDC0_MDSCR, MR3 write, CS0 */
> > +DATA 4 0x021b001c 0x00048031 /* MMDC0_MDSCR, MR1 write, CS0 */
> > +DATA 4 0x021b001c 0x15208030 /* MMDC0_MDSCR, MR0 write, CS0 */
> > +DATA 4 0x021b001c 0x04008040 /* MMDC0_MDSCR, ZQ calibration
> > command
> > sent to
> > + device on CS0 */
> > +
> > +DATA 4 0x021b0020 0x00007800 /* MMDC0_MDREF */
> > +DATA 4 0x021b0818 0x00000227 /* DDR_PHY_P0_MPODTCTRL */
> > +DATA 4 0x021b0004 0x0002556D /* MMDC0_MDPDC now SDCTL power down
> > enabled */ +DATA 4 0x021b0404 0x00011006 /* MMDC0_MAPSR ADOPT power
> > down enabled, MMDC will
> > + enter automatically to self-refresh
> > while the
> > + number of idle cycle reached. */
> > +DATA 4 0x021b001c 0x00000000 /* MMDC0_MDSCR, clear this register
> > (especially
> > + the configuration bit as
> > initialization is
> > + complete) */
> > +
> > +DATA 4 0x021b0890 0x00400A38
> > diff --git a/board/phytec/pcl063/pcl063.c
> > b/board/phytec/pcl063/pcl063.c new file mode 100644
> > index 0000000000..c376b64730
> > --- /dev/null
> > +++ b/board/phytec/pcl063/pcl063.c
> > @@ -0,0 +1,379 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright (C) 2018 Collabora Ltd.
> > + *
> > + * Based on board/ccv/xpress/xpress.c:
> > + * Copyright (C) 2015-2016 Stefan Roese <sr at denx.de>
> > + */
> > +
> > +#include <asm/arch/clock.h>
> > +#include <asm/arch/crm_regs.h>
> > +#include <asm/arch/mx6-pins.h>
> > +#include <asm/arch/sys_proto.h>
> > +#include <asm/mach-imx/iomux-v3.h>
> > +#include <asm/mach-imx/mxc_i2c.h>
> > +#include <fsl_esdhc.h>
> > +#include <linux/bitops.h>
> > +#include <miiphy.h>
> > +#include <netdev.h>
> > +#include <usb.h>
> > +#include <usb/ehci-ci.h>
> > +
> > +DECLARE_GLOBAL_DATA_PTR;
> > +
> > +int dram_init(void)
> > +{
> > + gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
> > PHYS_SDRAM_SIZE); +
> > + return 0;
> > +}
> > +
> > +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |
> > \
> > + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
> > + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | \
> > + PAD_CTL_HYS)
> > +
> > +static iomux_v3_cfg_t const uart1_pads[] = {
> > + MX6_PAD_UART1_TX_DATA__UART1_DCE_TX |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > + MX6_PAD_UART1_RX_DATA__UART1_DCE_RX |
> > MUX_PAD_CTRL(UART_PAD_CTRL), +};
> > +
> > +static iomux_v3_cfg_t const uart5_pads[] = {
> > + MX6_PAD_UART5_TX_DATA__UART5_DCE_TX |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > + MX6_PAD_UART5_RX_DATA__UART5_DCE_RX |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > + MX6_PAD_GPIO1_IO09__UART5_DCE_CTS |
> > MUX_PAD_CTRL(UART_PAD_CTRL),
> > + MX6_PAD_GPIO1_IO08__UART5_DCE_RTS |
> > MUX_PAD_CTRL(UART_PAD_CTRL), +};
> > +
> > +static void setup_iomux_uart(void)
> > +{
> > + imx_iomux_v3_setup_multiple_pads(uart1_pads,
> > ARRAY_SIZE(uart1_pads));
> > + imx_iomux_v3_setup_multiple_pads(uart5_pads,
> > ARRAY_SIZE(uart5_pads)); +}
> > +
> > +#ifdef CONFIG_USB_EHCI_MX6
> > +
> > +#define USB_OTHERREGS_OFFSET 0x800
> > +#define UCTRL_PWR_POL BIT(9)
> > +
> > +#define OTGID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
> > + PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
> > + PAD_CTL_DSE_80ohm | PAD_CTL_HYS | \
> > + PAD_CTL_SRE_FAST)
> > +
> > +static iomux_v3_cfg_t const usb_otg_pads[] = {
> > + /* OTG1 */
> > + MX6_PAD_SD1_CMD__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
> > + MX6_PAD_SD1_DATA0__ANATOP_OTG1_ID |
> > MUX_PAD_CTRL(OTGID_PAD_CTRL),
> > + /* OTG2 */
> > + MX6_PAD_SD1_DATA1__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
> > + MX6_PAD_SD1_DATA3__ANATOP_OTG2_ID |
> > MUX_PAD_CTRL(OTGID_PAD_CTRL), +};
> > +
> > +static void setup_usb(void)
> > +{
> > + imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
> > + ARRAY_SIZE(usb_otg_pads));
> > +}
> > +
> > +int board_usb_phy_mode(int port)
> > +{
> > + if (port == 1)
> > + return USB_INIT_HOST;
> > + else
> > + return usb_phy_mode(port);
> > +}
> > +
> > +int board_ehci_hcd_init(int port)
> > +{
> > + u32 *usbnc_usb_ctrl;
> > +
> > + if (port > 1)
> > + return -EINVAL;
> > +
> > + usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR +
> > USB_OTHERREGS_OFFSET +
> > + port * 4);
> > +
> > + /* Set Power polarity */
> > + setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
> > +
> > + return 0;
> > +}
> > +
> > +#endif /* CONFIG_USB_EHCI_MX6 */
> > +
> > +#ifdef CONFIG_SYS_I2C_MXC
> > +
> > +#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
> > + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
> > + PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
> > + PAD_CTL_ODE)
> > +
> > +#define I2CPC MUX_PAD_CTRL(I2C_PAD_CTRL)
> > +
> > +static struct i2c_pads_info i2c_pad_info1 = {
> > + .scl = {
> > + .i2c_mode = MX6_PAD_UART4_TX_DATA__I2C1_SCL | I2CPC,
> > + .gpio_mode = MX6_PAD_UART4_TX_DATA__GPIO1_IO28 |
> > I2CPC,
> > + .gp = IMX_GPIO_NR(1, 28),
> > + },
> > + .sda = {
> > + .i2c_mode = MX6_PAD_UART4_RX_DATA__I2C1_SDA | I2CPC,
> > + .gpio_mode = MX6_PAD_UART4_RX_DATA__GPIO1_IO29 |
> > I2CPC,
> > + .gp = IMX_GPIO_NR(1, 29),
> > + },
> > +};
> > +
> > +#endif /* CONFIG_SYS_I2C_MXC */
> > +
> > +#ifdef CONFIG_NAND_MXS
> > +
> > +#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | \
> > + PAD_CTL_PUS_100K_UP)
> > +
> > +#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
> > + PAD_CTL_SRE_FAST)
> > +
> > +#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
> > +
> > +#define GPMIPC MUX_PAD_CTRL(GPMI_PAD_CTRL2)
> > +
> > +static iomux_v3_cfg_t gpmi_pads[] = {
> > + IOMUX_PADS(PAD_NAND_DATA00__RAWNAND_DATA00 | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_DATA01__RAWNAND_DATA01 | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_DATA02__RAWNAND_DATA02 | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_DATA03__RAWNAND_DATA03 | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_DATA04__RAWNAND_DATA04 | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_DATA05__RAWNAND_DATA05 | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_DATA06__RAWNAND_DATA06 | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_DATA07__RAWNAND_DATA07 | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_CLE__RAWNAND_CLE | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_ALE__RAWNAND_ALE | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_CE0_B__RAWNAND_CE0_B | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_RE_B__RAWNAND_RE_B | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_WE_B__RAWNAND_WE_B | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_WP_B__RAWNAND_WP_B | GPMIPC),
> > + IOMUX_PADS(PAD_NAND_READY_B__RAWNAND_READY_B | GPMIPC),
> > +};
> > +
> > +static void setup_gpmi_nand(void)
> > +{
> > + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg
> > *)CCM_BASE_ADDR; +
> > + /* config gpmi nand iomux */
> > + SETUP_IOMUX_PADS(gpmi_pads);
> > +
> > + clrbits_le32(&mxc_ccm->CCGR4,
> > + MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
> > + MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK
> > +
> > MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
> > + MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
> > + MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
> > +
> > + /*
> > + * config gpmi and bch clock to 100 MHz
> > + * bch/gpmi select PLL2 PFD2 400M
> > + * 100M = 400M / 4
> > + */
> > + clrbits_le32(&mxc_ccm->cscmr1,
> > + MXC_CCM_CSCMR1_BCH_CLK_SEL |
> > + MXC_CCM_CSCMR1_GPMI_CLK_SEL);
> > + clrsetbits_le32(&mxc_ccm->cscdr1,
> > + MXC_CCM_CSCDR1_BCH_PODF_MASK |
> > + MXC_CCM_CSCDR1_GPMI_PODF_MASK,
> > + (3 << MXC_CCM_CSCDR1_BCH_PODF_OFFSET) |
> > + (3 << MXC_CCM_CSCDR1_GPMI_PODF_OFFSET));
> > +
> > + /* enable gpmi and bch clock gating */
> > + setbits_le32(&mxc_ccm->CCGR4,
> > + MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
> > + MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK
> > +
> > MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
> > + MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
> > + MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
> > +
> > + /* enable apbh clock gating */
> > + setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
> > +}
> > +
> > +#endif /* CONFIG_NAND_MXS */
> > +
> > +#ifdef CONFIG_FEC_MXC
> > +
> > +#define ENET_CLK_PAD_CTRL (PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
> > +
> > +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP |
> > PAD_CTL_PUE |
> > \
> > + PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm |
> > \
> > + PAD_CTL_SRE_FAST)
> > +
> > +#define MDIO_PAD_CTRL (PAD_CTL_PUS_100K_UP |
> > PAD_CTL_PUE | \
> > + PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST | \
> > + PAD_CTL_ODE)
> > +
> > +/*
> > + * pin conflicts for fec1 and fec2, GPIO1_IO06 and GPIO1_IO07 can
> > only
> > + * be used for ENET1 or ENET2, cannot be used for both.
> > + */
> > +static iomux_v3_cfg_t const fec1_pads[] = {
> > + MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
> > + MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_TX_EN__ENET1_TX_EN |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 |
> > MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
> > + MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_RX_ER__ENET1_RX_ER |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET1_RX_EN__ENET1_RX_EN |
> > MUX_PAD_CTRL(ENET_PAD_CTRL), +};
> > +
> > +static iomux_v3_cfg_t const fec2_pads[] = {
> > + MX6_PAD_GPIO1_IO06__ENET2_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
> > + MX6_PAD_GPIO1_IO07__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
> > +
> > + MX6_PAD_ENET2_TX_DATA0__ENET2_TDATA00 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET2_TX_DATA1__ENET2_TDATA01 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 |
> > MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
> > + MX6_PAD_ENET2_TX_EN__ENET2_TX_EN |
> > MUX_PAD_CTRL(ENET_PAD_CTRL), +
> > + MX6_PAD_ENET2_RX_DATA0__ENET2_RDATA00 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET2_RX_DATA1__ENET2_RDATA01 |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET2_RX_EN__ENET2_RX_EN |
> > MUX_PAD_CTRL(ENET_PAD_CTRL),
> > + MX6_PAD_ENET2_RX_ER__ENET2_RX_ER |
> > MUX_PAD_CTRL(ENET_PAD_CTRL), +};
> > +
> > +static void setup_iomux_fec(int fec_id)
> > +{
> > + if (fec_id == 0)
> > + imx_iomux_v3_setup_multiple_pads(fec1_pads,
> > +
> > ARRAY_SIZE(fec1_pads));
> > + else
> > + imx_iomux_v3_setup_multiple_pads(fec2_pads,
> > +
> > ARRAY_SIZE(fec2_pads)); +}
> > +
> > +int board_eth_init(bd_t *bis)
> > +{
> > + setup_iomux_fec(CONFIG_FEC_ENET_DEV);
> > +
> > + return fecmxc_initialize_multi(bis, CONFIG_FEC_ENET_DEV,
> > + CONFIG_FEC_MXC_PHYADDR,
> > IMX_FEC_BASE); +}
> > +
> > +static int setup_fec(int fec_id)
> > +{
> > + struct iomuxc *const iomuxc_regs = (struct iomuxc
> > *)IOMUXC_BASE_ADDR;
> > + int ret;
> > +
> > + if (fec_id == 0) {
> > + /*
> > + * Use 50M anatop loopback REF_CLK1 for ENET1,
> > + * clear gpr1[13], set gpr1[17].
> > + */
> > + clrsetbits_le32(&iomuxc_regs->gpr[1],
> > IOMUX_GPR1_FEC1_MASK,
> > + IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
> > + } else {
> > + /*
> > + * Use 50M anatop loopback REF_CLK2 for ENET2,
> > + * clear gpr1[14], set gpr1[18].
> > + */
> > + clrsetbits_le32(&iomuxc_regs->gpr[1],
> > IOMUX_GPR1_FEC2_MASK,
> > + IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
> > + }
> > +
> > + ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
> > + if (ret)
> > + return ret;
> > +
> > + enable_enet_clk(1);
> > +
> > + return 0;
> > +}
> > +
> > +int board_phy_config(struct phy_device *phydev)
> > +{
> > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
> > +
> > + if (phydev->drv->config)
> > + phydev->drv->config(phydev);
> > +
> > + return 0;
> > +}
> > +#endif /* CONFIG_FEC_MXC */
> > +
> > +#ifdef CONFIG_FSL_ESDHC
> > +
> > +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |
> > \
> > + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
> > + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | \
> > + PAD_CTL_HYS)
> > +
> > +static iomux_v3_cfg_t const usdhc1_pads[] = {
> > + MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > + MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > + MX6_PAD_SD1_DATA0__USDHC1_DATA0 |
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > + MX6_PAD_SD1_DATA1__USDHC1_DATA1 |
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > + MX6_PAD_SD1_DATA2__USDHC1_DATA2 |
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > + MX6_PAD_SD1_DATA3__USDHC1_DATA3 |
> > MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > + MX6_PAD_UART1_RTS_B__USDHC1_CD_B |
> > MUX_PAD_CTRL(USDHC_PAD_CTRL), +};
> > +
> > +static struct fsl_esdhc_cfg usdhc_cfg[] = {
> > + {
> > + .esdhc_base = USDHC1_BASE_ADDR,
> > + .max_bus_width = 4,
> > + },
> > +};
> > +
> > +int board_mmc_getcd(struct mmc *mmc)
> > +{
> > + return 1;
> > +}
> > +
> > +int board_mmc_init(bd_t *bis)
> > +{
> > + imx_iomux_v3_setup_multiple_pads(usdhc1_pads,
> > ARRAY_SIZE(usdhc1_pads));
> > + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
> > +
> > + return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
> > +}
> > +
> > +#endif /* CONFIG_FSL_ESDHC */
> > +
> > +int board_early_init_f(void)
> > +{
> > + setup_iomux_uart();
> > +
> > + return 0;
> > +}
> > +
> > +int board_init(void)
> > +{
> > + /* Address of boot parameters */
> > + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
> > +
> > +#ifdef CONFIG_SYS_I2C_MXC
> > + setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
> > +#endif
> > +
> > +#ifdef CONFIG_NAND_MXS
> > + setup_gpmi_nand();
> > +#endif
> > +
> > +#ifdef CONFIG_FEC_MXC
> > + setup_fec(CONFIG_FEC_ENET_DEV);
> > +#endif
> > +
> > +#ifdef CONFIG_USB_EHCI_MX6
> > + setup_usb();
> > +#endif
> > +
> > + return 0;
> > +}
> > +
> > +int checkboard(void)
> > +{
> > + puts("Board: PHYTEC phyCORE-i.MX6UL\n");
> > +
> > + return 0;
> > +}
> > diff --git a/board/phytec/pcl063/spl.c b/board/phytec/pcl063/spl.c
> > new file mode 100644
> > index 0000000000..e2a13efe91
> > --- /dev/null
> > +++ b/board/phytec/pcl063/spl.c
> > @@ -0,0 +1,118 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright (C) 2018 Collabora Ltd.
> > + *
> > + * Based on board/ccv/xpress/spl.c:
> > + * Copyright (C) 2015-2016 Stefan Roese <sr at denx.de>
> > + */
> > +
> > +#include <common.h>
> > +#include <spl.h>
> > +#include <asm/io.h>
> > +#include <asm/arch/mx6-ddr.h>
> > +#include <asm/arch/crm_regs.h>
> > +
> > +/* Configuration for Micron MT41K256M16TW-107 IT:P, 32M x 16 x 8
> > ->
> > 256MiB */ +
> > +static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
> > + .grp_addds = 0x00000030,
> > + .grp_ddrmode_ctl = 0x00020000,
> > + .grp_b0ds = 0x00000030,
> > + .grp_ctlds = 0x00000030,
> > + .grp_b1ds = 0x00000030,
> > + .grp_ddrpke = 0x00000000,
> > + .grp_ddrmode = 0x00020000,
> > + .grp_ddr_type = 0x000c0000,
> > +};
> > +
> > +static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
> > + .dram_dqm0 = 0x00000030,
> > + .dram_dqm1 = 0x00000030,
> > + .dram_ras = 0x00000030,
> > + .dram_cas = 0x00000030,
> > + .dram_odt0 = 0x00000030,
> > + .dram_odt1 = 0x00000030,
> > + .dram_sdba2 = 0x00000000,
> > + .dram_sdclk_0 = 0x00000030,
> > + .dram_sdqs0 = 0x00000030,
> > + .dram_sdqs1 = 0x00000030,
> > + .dram_reset = 0x00000030,
> > +};
> > +
> > +static struct mx6_mmdc_calibration mx6_mmcd_calib = {
> > + .p0_mpwldectrl0 = 0x00000000,
> > + .p0_mpdgctrl0 = 0x41480148,
> > + .p0_mprddlctl = 0x40403E42,
> > + .p0_mpwrdlctl = 0x40405852,
> > +};
> > +
> > +struct mx6_ddr_sysinfo ddr_sysinfo = {
> > + .dsize = 0, /* Bus size = 16bit */
> > + .cs_density = 18,
> > + .ncs = 1,
> > + .cs1_mirror = 0,
> > + .rtt_wr = 1,
> > + .rtt_nom = 1,
> > + .walat = 1, /* Write additional latency */
> > + .ralat = 5, /* Read additional latency */
> > + .mif3_mode = 3, /* Command prediction working
> > mode */
> > + .bi_on = 1, /* Bank interleaving enabled */
> > + .pd_fast_exit = 1,
> > + .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC
> > default) */
> > + .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC
> > default) */
> > + .ddr_type = DDR_TYPE_DDR3,
> > + .refsel = 1, /* Refresh cycles at 32KHz */
> > + .refr = 7, /* 8 refresh commands per refresh
> > cycle */ +};
> > +
> > +static struct mx6_ddr3_cfg mem_ddr = {
> > + .mem_speed = 933,
> > + .density = 4,
> > + .width = 16,
> > + .banks = 8,
> > + .rowaddr = 14,
> > + .coladdr = 10,
> > + .pagesz = 1,
> > + .trcd = 1391,
> > + .trcmin = 4791,
> > + .trasmin = 3400,
> > +};
> > +
> > +static void ccgr_init(void)
> > +{
> > + struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg
> > *)CCM_BASE_ADDR; +
> > + writel(0xFFFFFFFF, &ccm->CCGR0);
> > + writel(0xFFFFFFFF, &ccm->CCGR1);
> > + writel(0xFFFFFFFF, &ccm->CCGR2);
> > + writel(0xFFFFFFFF, &ccm->CCGR3);
> > + writel(0xFFFFFFFF, &ccm->CCGR4);
> > + writel(0xFFFFFFFF, &ccm->CCGR5);
> > + writel(0xFFFFFFFF, &ccm->CCGR6);
> > +}
> > +
> > +static void spl_dram_init(void)
> > +{
> > + mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs,
> > &mx6_grp_ioregs);
> > + mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
> > +}
> > +
> > +void board_init_f(ulong dummy)
> > +{
> > + ccgr_init();
> > +
> > + /* Setup AIPS and disable watchdog */
> > + arch_cpu_init();
> > +
> > + /* Setup iomux and i2c */
> > + board_early_init_f();
> > +
> > + /* Setup GP timer */
> > + timer_init();
> > +
> > + /* UART clocks enabled and gd valid - init serial console */
> > + preloader_console_init();
> > +
> > + /* DDR initialization */
> > + spl_dram_init();
> > +}
> > diff --git a/configs/phycore_pcl063_defconfig
> > b/configs/phycore_pcl063_defconfig new file mode 100644
> > index 0000000000..22f2d280f4
> > --- /dev/null
> > +++ b/configs/phycore_pcl063_defconfig
> > @@ -0,0 +1,47 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_MX6=y
> > +CONFIG_SYS_TEXT_BASE=0x87800000
> > +CONFIG_SPL_LIBCOMMON_SUPPORT=y
> > +CONFIG_SPL_LIBGENERIC_SUPPORT=y
> > +CONFIG_TARGET_PCL063=y
> > +CONFIG_DISTRO_DEFAULTS=y
> > +CONFIG_NR_DRAM_BANKS=8
> > +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/phytec/pcl063/imximage.
> > cfg"
> > +CONFIG_BOOTDELAY=3
> > +# CONFIG_USE_BOOTCOMMAND is not set
> > +CONFIG_BOARD_EARLY_INIT_F=y
> > +CONFIG_CMD_BOOTZ=y
> > +CONFIG_CMD_MEMTEST=y
> > +CONFIG_CMD_GPIO=y
> > +CONFIG_CMD_GPT=y
> > +# CONFIG_RANDOM_UUID is not set
> > +CONFIG_CMD_I2C=y
> > +CONFIG_CMD_MMC=y
> > +CONFIG_CMD_USB=y
> > +CONFIG_CMD_USB_SDP=y
> > +CONFIG_CMD_DHCP=y
> > +CONFIG_CMD_PING=y
> > +CONFIG_CMD_CACHE=y
> > +CONFIG_CMD_EXT2=y
> > +CONFIG_CMD_EXT4=y
> > +CONFIG_CMD_FAT=y
> > +CONFIG_CMD_UBI=y
> > +# CONFIG_ISO_PARTITION is not set
> > +# CONFIG_EFI_PARTITION is not set
> > +CONFIG_SYS_I2C_MXC=y
> > +CONFIG_FSL_ESDHC=y
> > +CONFIG_MTD=y
> > +CONFIG_NAND=y
> > +CONFIG_NAND_MXS=y
> > +CONFIG_PHYLIB=y
> > +CONFIG_PHY_MICREL=y
> > +CONFIG_MXC_UART=y
> > +CONFIG_USB=y
> > +CONFIG_USB_STORAGE=y
> > +CONFIG_USB_GADGET=y
> > +CONFIG_USB_GADGET_MANUFACTURER="Phytec"
> > +CONFIG_USB_GADGET_VENDOR_NUM=0x01b67
> > +CONFIG_USB_GADGET_PRODUCT_NUM=0x4fff
> > +CONFIG_CI_UDC=y
> > +CONFIG_USB_GADGET_DOWNLOAD=y
> > +CONFIG_OF_LIBFDT=y
> > diff --git a/configs/phycore_pcl063_spl_defconfig
> > b/configs/phycore_pcl063_spl_defconfig new file mode 100644
> > index 0000000000..0d3cda09a4
> > --- /dev/null
> > +++ b/configs/phycore_pcl063_spl_defconfig
> > @@ -0,0 +1,55 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_MX6=y
> > +CONFIG_SYS_TEXT_BASE=0x87800000
> > +CONFIG_SPL_LIBCOMMON_SUPPORT=y
> > +CONFIG_SPL_LIBGENERIC_SUPPORT=y
> > +CONFIG_TARGET_PCL063=y
> > +CONFIG_SPL_MMC_SUPPORT=y
> > +CONFIG_SPL_SERIAL_SUPPORT=y
> > +CONFIG_SPL_WATCHDOG_SUPPORT=y
> > +CONFIG_DISTRO_DEFAULTS=y
> > +CONFIG_NR_DRAM_BANKS=8
> > +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
> > +CONFIG_BOOTDELAY=3
> > +# CONFIG_USE_BOOTCOMMAND is not set
> > +CONFIG_BOARD_EARLY_INIT_F=y
> > +CONFIG_SPL=y
> > +CONFIG_SPL_RAW_IMAGE_SUPPORT=y
> > +CONFIG_SPL_USB_HOST_SUPPORT=y
> > +CONFIG_SPL_USB_GADGET_SUPPORT=y
> > +CONFIG_SPL_USB_SDP_SUPPORT=y
> > +CONFIG_CMD_BOOTZ=y
> > +CONFIG_CMD_MEMTEST=y
> > +CONFIG_CMD_GPIO=y
> > +CONFIG_CMD_GPT=y
> > +# CONFIG_RANDOM_UUID is not set
> > +CONFIG_CMD_I2C=y
> > +CONFIG_CMD_MMC=y
> > +CONFIG_CMD_USB=y
> > +CONFIG_CMD_USB_SDP=y
> > +CONFIG_CMD_DHCP=y
> > +CONFIG_CMD_PING=y
> > +CONFIG_CMD_CACHE=y
> > +CONFIG_CMD_EXT2=y
> > +CONFIG_CMD_EXT4=y
> > +CONFIG_CMD_FAT=y
> > +CONFIG_CMD_UBI=y
> > +# CONFIG_ISO_PARTITION is not set
> > +# CONFIG_EFI_PARTITION is not set
> > +CONFIG_SYS_I2C_MXC=y
> > +CONFIG_FSL_ESDHC=y
> > +CONFIG_MTD=y
> > +CONFIG_NAND=y
> > +CONFIG_NAND_MXS=y
> > +CONFIG_PHYLIB=y
> > +CONFIG_PHY_MICREL=y
> > +CONFIG_MXC_UART=y
> > +CONFIG_USB=y
> > +CONFIG_USB_STORAGE=y
> > +CONFIG_USB_GADGET=y
> > +CONFIG_USB_GADGET_MANUFACTURER="Phytec"
> > +CONFIG_USB_GADGET_VENDOR_NUM=0x01b67
> > +CONFIG_USB_GADGET_PRODUCT_NUM=0x4fff
> > +CONFIG_CI_UDC=y
> > +CONFIG_USB_GADGET_DOWNLOAD=y
> > +CONFIG_OF_LIBFDT=y
> > diff --git a/include/configs/pcl063.h b/include/configs/pcl063.h
> > new file mode 100644
> > index 0000000000..83235a73c1
> > --- /dev/null
> > +++ b/include/configs/pcl063.h
> > @@ -0,0 +1,107 @@
> > +/* SPDX-License-Identifier: GPL-2.0+ */
> > +/*
> > + * Copyright (C) 2018 Collabora Ltd.
> > + *
> > + * Based on include/configs/xpress.h:
> > + * Copyright (C) 2015-2016 Stefan Roese <sr at denx.de>
> > + */
> > +#ifndef __PCL063_H
> > +#define __PCL063_H
> > +
> > +#include <linux/sizes.h>
> > +#include "mx6_common.h"
> > +
> > +/* SPL options */
> > +#include "imx6_spl.h"
> > +
> > +/*
> > + * There is a bug in some i.MX6UL processors that results in the
> > initial
> > + * portion of OCRAM being unavailable when booting from (at least)
> > an SD
> > + * card.
> > + *
> > + * Tweak the SPL text base address to avoid this.
> > + */
> > +#undef CONFIG_SPL_TEXT_BASE
> > +#define CONFIG_SPL_TEXT_BASE 0x00909000
> > +
> > +/* Size of malloc() pool */
> > +#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M)
> > +
> > +/* Console configs */
> > +#define CONFIG_MXC_UART_BASE UART1_BASE
> > +
> > +/* MMC Configs */
> > +#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
> > +
> > +/* I2C configs */
> > +#define CONFIG_SYS_I2C
> > +#ifndef CONFIG_SYS_I2C_MXC
> > +#define CONFIG_SYS_I2C_MXC
> > +#endif
> > +#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
> > +#define CONFIG_SYS_I2C_SPEED 100000
> > +
> > +/* Miscellaneous configurable options */
> > +#define CONFIG_SYS_MEMTEST_START 0x80000000
> > +#define CONFIG_SYS_MEMTEST_END
> > (CONFIG_SYS_MEMTEST_START + 0x10000000) +
> > +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
> > +#define CONFIG_SYS_HZ 1000
> > +
> > +/* Physical Memory Map */
> > +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
> > +#define PHYS_SDRAM_SIZE SZ_256M
> > +
> > +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
> > +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
> > +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
> > +
> > +#define CONFIG_SYS_INIT_SP_OFFSET \
> > + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
> > +#define CONFIG_SYS_INIT_SP_ADDR \
> > + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
> > +
> > +#define CONFIG_ENV_SIZE (16 << 10)
> > +#define CONFIG_ENV_OFFSET (512 << 10)
> > +
> > +/* NAND */
> > +#define CONFIG_SYS_MAX_NAND_DEVICE 1
> > +#define CONFIG_SYS_NAND_BASE 0x40000000
> > +
> > +/* USB Configs */
> > +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
> > +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI |
> > PORT_PTS_PTW) +#define CONFIG_MXC_USB_FLAGS 0
> > +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
> > +
> > +#ifdef CONFIG_CMD_NET
> > +#define CONFIG_FEC_MXC
> > +#define CONFIG_MII
> > +#define CONFIG_FEC_ENET_DEV 0
> > +
> > +#if (CONFIG_FEC_ENET_DEV == 0)
> > +#define IMX_FEC_BASE ENET_BASE_ADDR
> > +#define CONFIG_FEC_MXC_PHYADDR 0x1
> > +#define CONFIG_FEC_XCV_TYPE RMII
> > +#elif (CONFIG_FEC_ENET_DEV == 1)
> > +#define IMX_FEC_BASE ENET2_BASE_ADDR
> > +#define CONFIG_FEC_MXC_PHYADDR 0x2
> > +#define CONFIG_FEC_XCV_TYPE RMII
> > +#endif
> > +#define CONFIG_ETHPRIME "FEC"
> > +#endif /* CONFIG_CMD_NET */
> > +
> > +#define CONFIG_IMX_THERMAL
> > +
> > +#define CONFIG_EXTRA_ENV_SETTINGS \
> > + "console=ttymxc0\0" \
> > + BOOTENV
> > +
> > +#define BOOT_TARGET_DEVICES(func) \
> > + func(MMC, mmc, 0) \
> > + func(UBIFS, ubifs, 0) \
> > + func(DHCP, dhcp, na)
> > +
> > +#include <config_distro_bootcmd.h>
> > +
> > +#endif /* __PCL063_H */
>
>
>
> Best regards,
>
> Lukasz Majewski
>
> --
>
> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email:
> lukma at denx.de
More information about the U-Boot
mailing list