[U-Boot] [PATCH v2 27/32] spi: mxc: Drop non-dm code
Jagan Teki
jagan at amarulasolutions.com
Sun Nov 25 17:28:48 UTC 2018
Drop the non-dm code, those board which uses non-dm need
to define DM_SPI. u-boot build trigger the warning for
the same.
Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
---
Makefile | 2 +-
drivers/spi/Makefile | 2 +-
drivers/spi/mxc_spi.c | 123 ++----------------------------------------
3 files changed, 5 insertions(+), 122 deletions(-)
diff --git a/Makefile b/Makefile
index 7c1d934493..3be3bb3118 100644
--- a/Makefile
+++ b/Makefile
@@ -920,7 +920,7 @@ ifeq ($(CONFIG_DM_I2C_COMPAT)$(CONFIG_SANDBOX),y)
endif
ifeq ($(CONFIG_DM_SPI),)
ifeq ($(filter $(CONFIG_DAVINCI_SPI) $(CONFIG_KIRKWOOD_SPI) $(CONFIG_MPC8XXX_SPI) \
- $(CONFIG_TI_QSPI),y),y)
+ $(CONFIG_MXC_SPI) $(CONFIG_TI_QSPI),y),y)
@echo "===================== WARNING ======================"
@echo "This board uses SPI driver from drivers/spi/ without"
@echo "enabling CONFIG_DM_SPI. Please enable CONFIG_DM_SPI"
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 49e614e124..c682b014e7 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -9,6 +9,7 @@ obj-y += spi-uclass.o
obj-$(CONFIG_DAVINCI_SPI) += davinci_spi.o
obj-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o
obj-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o
+obj-$(CONFIG_MXC_SPI) += mxc_spi.o
obj-$(CONFIG_SANDBOX) += spi-emul-uclass.o
obj-$(CONFIG_SOFT_SPI) += soft_spi.o
obj-$(CONFIG_SPI_MEM) += spi-mem.o
@@ -33,7 +34,6 @@ obj-$(CONFIG_ICH_SPI) += ich.o
obj-$(CONFIG_MPC8XX_SPI) += mpc8xx_spi.o
obj-$(CONFIG_MT7621_SPI) += mt7621_spi.o
obj-$(CONFIG_MVEBU_A3700_SPI) += mvebu_a3700_spi.o
-obj-$(CONFIG_MXC_SPI) += mxc_spi.o
obj-$(CONFIG_ATCSPI200_SPI) += atcspi200_spi.o
obj-$(CONFIG_OMAP3_SPI) += omap3_spi.o
obj-$(CONFIG_PIC32_SPI) += pic32_spi.o
diff --git a/drivers/spi/mxc_spi.c b/drivers/spi/mxc_spi.c
index b2636909ce..f6c6685e7e 100644
--- a/drivers/spi/mxc_spi.c
+++ b/drivers/spi/mxc_spi.c
@@ -57,26 +57,6 @@ static inline struct mxc_spi_slave *to_mxc_spi_slave(struct spi_slave *slave)
return container_of(slave, struct mxc_spi_slave, slave);
}
-static void mxc_spi_cs_activate(struct mxc_spi_slave *mxcs)
-{
- if (CONFIG_IS_ENABLED(DM_SPI)) {
- dm_gpio_set_value(&mxcs->ss, 1);
- } else {
- if (mxcs->gpio > 0)
- gpio_set_value(mxcs->gpio, mxcs->ss_pol);
- }
-}
-
-static void mxc_spi_cs_deactivate(struct mxc_spi_slave *mxcs)
-{
- if (CONFIG_IS_ENABLED(DM_SPI)) {
- dm_gpio_set_value(&mxcs->ss, 0);
- } else {
- if (mxcs->gpio > 0)
- gpio_set_value(mxcs->gpio, !(mxcs->ss_pol));
- }
-}
-
u32 get_cspi_div(u32 div)
{
int i;
@@ -345,7 +325,7 @@ static int mxc_spi_xfer_internal(struct mxc_spi_slave *mxcs,
return -EINVAL;
if (flags & SPI_XFER_BEGIN)
- mxc_spi_cs_activate(mxcs);
+ dm_gpio_set_value(&mxcs->ss, 1);
while (n_bytes > 0) {
if (n_bytes < MAX_SPI_BYTES)
@@ -366,9 +346,8 @@ static int mxc_spi_xfer_internal(struct mxc_spi_slave *mxcs,
n_bytes -= blk_size;
}
- if (flags & SPI_XFER_END) {
- mxc_spi_cs_deactivate(mxcs);
- }
+ if (flags & SPI_XFER_END)
+ dm_gpio_set_value(&mxcs->ss, 0);
return 0;
}
@@ -391,101 +370,6 @@ static int mxc_spi_claim_bus_internal(struct mxc_spi_slave *mxcs, int cs)
return 0;
}
-#ifndef CONFIG_DM_SPI
-int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
- void *din, unsigned long flags)
-{
- struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave);
-
- return mxc_spi_xfer_internal(mxcs, bitlen, dout, din, flags);
-}
-
-/*
- * Some SPI devices require active chip-select over multiple
- * transactions, we achieve this using a GPIO. Still, the SPI
- * controller has to be configured to use one of its own chipselects.
- * To use this feature you have to implement board_spi_cs_gpio() to assign
- * a gpio value for each cs (-1 if cs doesn't need to use gpio).
- * You must use some unused on this SPI controller cs between 0 and 3.
- */
-static int setup_cs_gpio(struct mxc_spi_slave *mxcs,
- unsigned int bus, unsigned int cs)
-{
- int ret;
-
- mxcs->gpio = board_spi_cs_gpio(bus, cs);
- if (mxcs->gpio == -1)
- return 0;
-
- gpio_request(mxcs->gpio, "spi-cs");
- ret = gpio_direction_output(mxcs->gpio, !(mxcs->ss_pol));
- if (ret) {
- printf("mxc_spi: cannot setup gpio %d\n", mxcs->gpio);
- return -EINVAL;
- }
-
- return 0;
-}
-
-static unsigned long spi_bases[] = {
- MXC_SPI_BASE_ADDRESSES
-};
-
-struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
- unsigned int max_hz, unsigned int mode)
-{
- struct mxc_spi_slave *mxcs;
- int ret;
-
- if (bus >= ARRAY_SIZE(spi_bases))
- return NULL;
-
- if (max_hz == 0) {
- printf("Error: desired clock is 0\n");
- return NULL;
- }
-
- mxcs = spi_alloc_slave(struct mxc_spi_slave, bus, cs);
- if (!mxcs) {
- puts("mxc_spi: SPI Slave not allocated !\n");
- return NULL;
- }
-
- mxcs->ss_pol = (mode & SPI_CS_HIGH) ? 1 : 0;
-
- ret = setup_cs_gpio(mxcs, bus, cs);
- if (ret < 0) {
- free(mxcs);
- return NULL;
- }
-
- mxcs->base = spi_bases[bus];
- mxcs->max_hz = max_hz;
- mxcs->mode = mode;
-
- return &mxcs->slave;
-}
-
-void spi_free_slave(struct spi_slave *slave)
-{
- struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave);
-
- free(mxcs);
-}
-
-int spi_claim_bus(struct spi_slave *slave)
-{
- struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave);
-
- return mxc_spi_claim_bus_internal(mxcs, slave->cs);
-}
-
-void spi_release_bus(struct spi_slave *slave)
-{
- /* TODO: Shut the controller down */
-}
-#else
-
static int mxc_spi_probe(struct udevice *bus)
{
struct mxc_spi_slave *plat = bus->platdata;
@@ -575,4 +459,3 @@ U_BOOT_DRIVER(mxc_spi) = {
.platdata_auto_alloc_size = sizeof(struct mxc_spi_slave),
.probe = mxc_spi_probe,
};
-#endif
--
2.18.0.321.gffc6fa0e3
More information about the U-Boot
mailing list