[U-Boot] [PATCH v2 3/3] imx: Add PHYTEC phyBOARD-i.MX6UL-Segin

[Marek Vasut]

On 11/23/2018 05:47 PM, Martyn Welch wrote:
> Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
> the PHYTEC phyCORE-i.MX6UL SOM (PCL063).

Nice ! A few nits below.

> This port provides both SPL and
> DCD based boot options (hence the two defconfigs).

Is the DCD option really needed or can it be dropped ? The SPL is far
more flexible.

> CPU:   Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
> CPU:   Industrial temperature grade (-40C to 105C) at 44C
> Reset cause: POR
> Board: PHYTEC phyCORE-i.MX6UL
> I2C:   ready
> DRAM:  256 MiB
> NAND:  512 MiB
> MMC:   FSL_SDHC: 0
> In:    serial
> Out:   serial
> Err:   serial
> Net:   FEC0
> 
> Working:
>  - Eth0
>  - i2C
>  - MMC/SD
>  - NAND
>  - UART (1 & 5)
>  - USB (host & otg)
> 
> Signed-off-by: Martyn Welch <martyn.welch at collabora.com>
> 
> ---
> 
> Changes in v2:
> - Switch to driver model
> 
>  arch/arm/dts/Makefile                 |   3 +-
>  arch/arm/dts/imx6ul-pcl063.dtsi       | 180 ++++++++++++++++++++++
>  arch/arm/dts/imx6ul-phycore-segin.dts |  76 ++++++++++
>  arch/arm/mach-imx/mx6/Kconfig         |  13 ++
>  board/phytec/pcl063/Kconfig           |  12 ++
>  board/phytec/pcl063/MAINTAINERS       |   9 ++
>  board/phytec/pcl063/Makefile          |   7 +
>  board/phytec/pcl063/README            |  43 ++++++
>  board/phytec/pcl063/imximage.cfg      | 177 ++++++++++++++++++++++
>  board/phytec/pcl063/pcl063.c          | 206 ++++++++++++++++++++++++++
>  board/phytec/pcl063/spl.c             | 118 +++++++++++++++
>  configs/phycore_pcl063_defconfig      |  66 +++++++++
>  configs/phycore_pcl063_spl_defconfig  |  71 +++++++++
>  include/configs/pcl063.h              | 100 +++++++++++++
>  14 files changed, 1080 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm/dts/imx6ul-pcl063.dtsi
>  create mode 100644 arch/arm/dts/imx6ul-phycore-segin.dts
>  create mode 100644 board/phytec/pcl063/Kconfig
>  create mode 100644 board/phytec/pcl063/MAINTAINERS
>  create mode 100644 board/phytec/pcl063/Makefile
>  create mode 100644 board/phytec/pcl063/README
>  create mode 100644 board/phytec/pcl063/imximage.cfg
>  create mode 100644 board/phytec/pcl063/pcl063.c
>  create mode 100644 board/phytec/pcl063/spl.c
>  create mode 100644 configs/phycore_pcl063_defconfig
>  create mode 100644 configs/phycore_pcl063_spl_defconfig
>  create mode 100644 include/configs/pcl063.h
> 
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index d36447d18d..ffda97a291 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -444,7 +444,8 @@ dtb-$(CONFIG_MX6UL) += \
>  	imx6ul-isiot-nand.dtb \
>  	imx6ul-opos6uldev.dtb \
>  	imx6ul-14x14-evk.dtb \
> -	imx6ul-9x9-evk.dtb
> +	imx6ul-9x9-evk.dtb \
> +	imx6ul-phycore-segin.dtb
>  
>  dtb-$(CONFIG_MX6ULL) += imx6ull-14x14-evk.dtb
>  
> diff --git a/arch/arm/dts/imx6ul-pcl063.dtsi b/arch/arm/dts/imx6ul-pcl063.dtsi
> new file mode 100644
> index 0000000000..fa63911480
> --- /dev/null
> +++ b/arch/arm/dts/imx6ul-pcl063.dtsi
> @@ -0,0 +1,180 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2018 Collabora Ltd.
> + *
> + * Based on dts[i] from Phytech barebox port:

"Phytec", fix globally.
But maybe you can pull the DT from upstream Linux instead ?

> + * Copyright (C) 2016 PHYTEC Messtechnik GmbH
> + * Author: Christian Hemp <c.hemp at phytec.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:

This is in the SPDX tag above, drop it.
[...]

> +int board_init(void)
> +{
> +	/* Address of boot parameters */
> +	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
> +
> +#ifdef CONFIG_NAND_MXS
> +	setup_gpmi_nand();
> +#endif
> +
> +#ifdef	CONFIG_FEC_MXC

ifdef[SPACE] instead of TAB, keep it consistent.

> +	setup_fec();
> +#endif
> +	return 0;
> +}

[...]
-- 
Best regards,
Marek Vasut