[U-Boot] [PATCH][v2] board/lx2160ardb: Add distro boot support
Priyanka Jain
priyanka.jain at nxp.com
Thu Nov 29 09:00:37 UTC 2018
Add u-boot enviroments to support distro boot which scan
boot.scr from external storage devices
(e.g. SD/USB/SATA/SCSI disk) and execute autoboot script.
Signed-off-by: Priyanka Jain <priyanka.jain at nxp.com>
---
Depends on https://patchwork.ozlabs.org/patch/990094/
Changes for v2:
xspi_bootcmd, sd_bootcmd env variables are
dependent on board. So, move the definition
from lx2160a_common.h file to lx2160ardb.h file
configs/lx2160ardb_tfa_defconfig | 3 +-
include/configs/lx2160a_common.h | 84 +++++++++++++++++++++++++++++++++++-----
include/configs/lx2160ardb.h | 29 +++++++-------
3 files changed, 90 insertions(+), 26 deletions(-)
diff --git a/configs/lx2160ardb_tfa_defconfig b/configs/lx2160ardb_tfa_defconfig
index 64cc31d..86fdcfc 100644
--- a/configs/lx2160ardb_tfa_defconfig
+++ b/configs/lx2160ardb_tfa_defconfig
@@ -6,7 +6,6 @@ CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
CONFIG_DEFAULT_DEVICE_TREE="fsl-lx2160a-rdb"
CONFIG_NR_DRAM_BANKS=3
CONFIG_DM=y
-CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
@@ -14,7 +13,7 @@ CONFIG_TFABOOT=y
CONFIG_BOOTDELAY=10
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyAMA0,115200 root=/dev/ram0 earlycon=pl011,mmio32,0x21c0000 ramdisk_size=0x2000000 default_hugepagesz=1024m hugepagesz=1024m hugepages=2 pci=pcie_bus_perf"
-# CONFIG_CMD_IMLS is not set
+# CONFIG_USE_BOOTCOMMAND is not set
CONFIG_CMD_GREPENV=y
CONFIG_CMD_EEPROM=y
CONFIG_CMD_GPT=y
diff --git a/include/configs/lx2160a_common.h b/include/configs/lx2160a_common.h
index 19053b43a1..5b4fabe 100644
--- a/include/configs/lx2160a_common.h
+++ b/include/configs/lx2160a_common.h
@@ -194,16 +194,6 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
/* Initial environment variables */
-#define XSPI_NOR_BOOTCOMMAND "fsl_mc apply dpl 0x20d00000;" \
- "sf probe 0:0;" \
- "sf read 0xa0000000 0x1000000 0x3000000;" \
- "bootm 0xa0000000"
-
-#define SD_BOOTCOMMAND "mmc read 0xa0000000 0x6800 0xA0;" \
- "fsl_mc apply dpl 0xa0000000;" \
- "mmc read 0xb0000000 0x8000 0x1d000;" \
- "bootm 0xb0000000"
-
#define XSPI_MC_INIT_CMD \
"fsl_mc start mc 0x20a00000 0x20e00000\0"
@@ -212,4 +202,78 @@ unsigned long get_board_ddr_clk(void);
"mmc read 0x80100000 0x7000 0x800;" \
"fsl_mc start mc 0x80000000 0x80100000\0"
+#define EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:bank_intlv=auto\0" \
+ "ramdisk_addr=0x800000\0" \
+ "ramdisk_size=0x2000000\0" \
+ "fdt_high=0xa0000000\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "fdt_addr=0x64f00000\0" \
+ "kernel_start=0x1000000\0" \
+ "kernelheader_start=0x800000\0" \
+ "scriptaddr=0x80000000\0" \
+ "scripthdraddr=0x80080000\0" \
+ "fdtheader_addr_r=0x80100000\0" \
+ "kernelheader_addr_r=0x80200000\0" \
+ "kernel_addr_r=0x81000000\0" \
+ "kernelheader_size=0x40000\0" \
+ "fdt_addr_r=0x90000000\0" \
+ "load_addr=0xa0000000\0" \
+ "kernel_size=0x2800000\0" \
+ "kernel_addr_sd=0x8000\0" \
+ "kernel_size_sd=0x1d000\0" \
+ "console=ttyAMA0,38400n8\0" \
+ BOOTENV \
+ "mcmemsize=0x70000000\0" \
+ XSPI_MC_INIT_CMD \
+ "boot_scripts=lx2160ardb_boot.scr\0" \
+ "boot_script_hdr=hdr_lx2160ardb_bs.out\0" \
+ "scan_dev_for_boot_part=" \
+ "part list ${devtype} ${devnum} devplist; " \
+ "env exists devplist || setenv devplist 1; " \
+ "for distro_bootpart in ${devplist}; do " \
+ "if fstype ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "bootfstype; then " \
+ "run scan_dev_for_boot; " \
+ "fi; " \
+ "done\0" \
+ "scan_dev_for_boot=" \
+ "echo Scanning ${devtype} " \
+ "${devnum}:${distro_bootpart}...; " \
+ "for prefix in ${boot_prefixes}; do " \
+ "run scan_dev_for_scripts; " \
+ "done;\0" \
+ "boot_a_script=" \
+ "load ${devtype} ${devnum}:${distro_bootpart} " \
+ "${scriptaddr} ${prefix}${script}; " \
+ "env exists secureboot && load ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "${scripthdraddr} ${prefix}${boot_script_hdr} " \
+ "&& esbc_validate ${scripthdraddr};" \
+ "source ${scriptaddr}\0"
+
+#define XSPI_NOR_BOOTCOMMAND \
+ "env exists mcinitcmd && env exists secureboot "\
+ "&& esbc_validate 0x20780000; " \
+ "env exists mcinitcmd && " \
+ "fsl_mc lazyapply dpl 0x20d00000; " \
+ "run distro_bootcmd;run xspi_bootcmd; " \
+ "env exists secureboot && esbc_halt;"
+
+#define SD_BOOTCOMMAND \
+ "env exists mcinitcmd && mmcinfo; " \
+ "mmc read 0x80001000 0x6800 0x800; " \
+ "env exists mcinitcmd && env exists secureboot " \
+ " && mmc read 0x80780000 0x3C00 0x10 " \
+ "&& esbc_validate 0x80780000;env exists mcinitcmd " \
+ "&& fsl_mc lazyapply dpl 0x80001000;" \
+ "run distro_bootcmd;run sd_bootcmd;" \
+ "env exists secureboot && esbc_halt;"
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(SCSI, scsi, 0)
+#include <config_distro_bootcmd.h>
+
#endif /* __LX2_COMMON_H */
diff --git a/include/configs/lx2160ardb.h b/include/configs/lx2160ardb.h
index 67d214d..8c91fea 100644
--- a/include/configs/lx2160ardb.h
+++ b/include/configs/lx2160ardb.h
@@ -81,21 +81,22 @@
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "hwconfig=fsl_ddr:bank_intlv=auto\0" \
- "scriptaddr=0x80800000\0" \
- "kernel_addr_r=0x81000000\0" \
- "pxefile_addr_r=0x81000000\0" \
- "fdt_addr_r=0x88000000\0" \
- "ramdisk_addr_r=0x89000000\0" \
- "loadaddr=0x80100000\0" \
- "kernel_addr=0x100000\0" \
- "ramdisk_addr=0x800000\0" \
- "ramdisk_size=0x2000000\0" \
- "fdt_high=0xa0000000\0" \
- "initrd_high=0xffffffffffffffff\0" \
- "kernel_start=0x21000000\0" \
+ EXTRA_ENV_SETTINGS \
"lx2160ardb_vdd_mv=800\0" \
- "mcmemsize=0x40000000\0"
+ "BOARD=lx2160ardb\0" \
+ "xspi_bootcmd=echo Trying load from flexspi..;" \
+ "sf probe 0:0 && sf read $load_addr " \
+ "$kernel_start $kernel_size ; env exists secureboot &&" \
+ "sf read $kernelheader_addr_r $kernelheader_start " \
+ "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
+ " bootm $load_addr#$BOARD\0" \
+ "sd_bootcmd=echo Trying load from sd card..;" \
+ "mmcinfo; mmc read $load_addr " \
+ "$kernel_addr_sd $kernel_size_sd ;" \
+ "env exists secureboot && mmc read $kernelheader_addr_r "\
+ "$kernelhdr_addr_sd $kernelhdr_size_sd " \
+ " && esbc_validate ${kernelheader_addr_r};" \
+ "bootm $load_addr#$BOARD\0"
#include <asm/fsl_secure_boot.h>
--
2.7.4
More information about the U-Boot
mailing list