[U-Boot] [PATCH u-boot-marvell v3 03/10] board: turris_mox: Check and configure modules

Stefan Roese sr at denx.de
Thu Nov 29 13:00:22 UTC 2018


On 20.11.18 13:04, Marek Behún wrote:
> Check if Mox modules are connected in supported mode, then configure
> the MDIO addresses of switch modules.
> 
> Signed-off-by: Marek Behún <marek.behun at nic.cz>
> ---
>   arch/arm/dts/armada-3720-turris-mox.dts |  11 ++
>   board/CZ.NIC/turris_mox/turris_mox.c    | 251 +++++++++++++++++++++++-
>   2 files changed, 261 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/dts/armada-3720-turris-mox.dts b/arch/arm/dts/armada-3720-turris-mox.dts
> index 7babc16679..9c96dd39a9 100644
> --- a/arch/arm/dts/armada-3720-turris-mox.dts
> +++ b/arch/arm/dts/armada-3720-turris-mox.dts
> @@ -110,6 +110,17 @@
>   		spi-max-frequency = <20000000>;
>   		m25p,fast-read;
>   	};
> +
> +	moxtet at 1 {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		compatible = "cznic,moxtet";
> +		reg = <1>;
> +		devrst-gpio = <&gpiosb 2 GPIO_ACTIVE_LOW>;
> +		spi-max-frequency = <1000000>;
> +		spi-cpol;
> +		spi-cpha;
> +	};
>   };
>   
>   &uart0 {
> diff --git a/board/CZ.NIC/turris_mox/turris_mox.c b/board/CZ.NIC/turris_mox/turris_mox.c
> index 3c0ab58756..39c26416a7 100644
> --- a/board/CZ.NIC/turris_mox/turris_mox.c
> +++ b/board/CZ.NIC/turris_mox/turris_mox.c
> @@ -4,11 +4,13 @@
>    */
>   
>   #include <common.h>
> +#include <asm/gpio.h>
>   #include <asm/io.h>
>   #include <dm.h>
>   #include <clk.h>
>   #include <spi.h>
>   #include <mvebu/comphy.h>
> +#include <miiphy.h>
>   #include <linux/string.h>
>   #include <linux/libfdt.h>
>   #include <fdt_support.h>
> @@ -239,11 +241,138 @@ int comphy_update_map(struct comphy_map *serdes_map, int count)
>   	return 0;
>   }
>   
> +#define SW_SMI_CMD_R(d, r)	(0x9800 | (((d) & 0x1f) << 5) | ((r) & 0x1f))
> +#define SW_SMI_CMD_W(d, r)	(0x9400 | (((d) & 0x1f) << 5) | ((r) & 0x1f))
> +
> +static int sw_multi_read(struct mii_dev *bus, int sw, int dev, int reg)
> +{
> +	bus->write(bus, sw, 0, 0, SW_SMI_CMD_R(dev, reg));
> +	mdelay(5);
> +	return bus->read(bus, sw, 0, 1);
> +}
> +
> +static void sw_multi_write(struct mii_dev *bus, int sw, int dev, int reg,
> +			   u16 val)
> +{
> +	bus->write(bus, sw, 0, 1, val);
> +	bus->write(bus, sw, 0, 0, SW_SMI_CMD_W(dev, reg));
> +	mdelay(5);
> +}
> +
> +static int sw_scratch_read(struct mii_dev *bus, int sw, int reg)
> +{
> +	sw_multi_write(bus, sw, 0x1c, 0x1a, (reg & 0x7f) << 8);
> +	return sw_multi_read(bus, sw, 0x1c, 0x1a) & 0xff;
> +}
> +
> +static void sw_led_write(struct mii_dev *bus, int sw, int port, int reg,
> +			 u16 val)
> +{
> +	sw_multi_write(bus, sw, port, 0x16, 0x8000 | ((reg & 7) << 12)
> +					    | (val & 0x7ff));
> +}
> +
> +static void sw_blink_leds(struct mii_dev *bus, int peridot, int topaz)
> +{
> +	int i, p;
> +	struct {
> +		int port;
> +		u16 val;
> +		int wait;
> +	} regs[] = {
> +		{ 2, 0xef, 1 }, { 2, 0xfe, 1 }, { 2, 0x33, 0 },
> +		{ 4, 0xef, 1 }, { 4, 0xfe, 1 }, { 4, 0x33, 0 },
> +		{ 3, 0xfe, 1 }, { 3, 0xef, 1 }, { 3, 0x33, 0 },
> +		{ 1, 0xfe, 1 }, { 1, 0xef, 1 }, { 1, 0x33, 0 }
> +	};
> +
> +	for (i = 0; i < 12; ++i) {
> +		for (p = 0; p < peridot; ++p) {
> +			sw_led_write(bus, 0x10 + p, regs[i].port, 0,
> +				     regs[i].val);
> +			sw_led_write(bus, 0x10 + p, regs[i].port + 4, 0,
> +				     regs[i].val);
> +		}
> +		if (topaz) {
> +			sw_led_write(bus, 0x2, 0x10 + regs[i].port, 0,
> +				     regs[i].val);
> +		}
> +
> +		if (regs[i].wait)
> +			mdelay(75);
> +	}
> +}
> +
> +static void check_switch_address(struct mii_dev *bus, int addr)
> +{
> +	if (sw_scratch_read(bus, addr, 0x70) >> 3 != addr)
> +		printf("Check of switch MDIO address failed for 0x%02x\n",
> +		       addr);
> +}
> +
> +static int sfp, pci, topaz, peridot, usb, passpci;
> +static int sfp_pos, peridot_pos[3];
> +static int module_count;
> +
> +static int configure_peridots(struct gpio_desc *reset_gpio)
> +{
> +	int i, ret;
> +	u8 dout[MAX_MOX_MODULES];
> +
> +	memset(dout, 0, MAX_MOX_MODULES);
> +
> +	/* set addresses of Peridot modules */
> +	for (i = 0; i < peridot; ++i)
> +		dout[module_count - peridot_pos[i]] = (~i) & 3;
> +
> +	/*
> +	 * if there is a SFP module connected to the last Peridot module, set
> +	 * the P10_SMODE to 1 for the Peridot module
> +	 */
> +	if (sfp)
> +		dout[module_count - peridot_pos[i - 1]] |= 1 << 3;
> +
> +	dm_gpio_set_value(reset_gpio, 1);
> +	mdelay(10);
> +
> +	ret = mox_do_spi(NULL, dout, module_count + 1);
> +
> +	mdelay(10);
> +	dm_gpio_set_value(reset_gpio, 0);
> +
> +	mdelay(50);
> +
> +	return ret;
> +}
> +
> +static int get_reset_gpio(struct gpio_desc *reset_gpio)
> +{
> +	int node;
> +
> +	node = fdt_node_offset_by_compatible(gd->fdt_blob, 0, "cznic,moxtet");
> +	if (node < 0) {
> +		printf("Cannot find Moxtet bus device node!\n");
> +		return -1;
> +	}
> +
> +	gpio_request_by_name_nodev(offset_to_ofnode(node), "devrst-gpio", 0,
> +				   reset_gpio, GPIOD_IS_OUT);
> +
> +	if (!dm_gpio_is_valid(reset_gpio)) {
> +		printf("Cannot find reset GPIO for Moxtet bus!\n");
> +		return -1;
> +	}
> +
> +	return 0;
> +}
> +
>   int last_stage_init(void)
>   {
>   	int ret, i;
>   	const u8 *topology;
> -	int module_count, is_sd;
> +	int is_sd;
> +	struct mii_dev *bus;
> +	struct gpio_desc reset_gpio = {};
>   
>   	ret = mox_get_topology(&topology, &module_count, &is_sd);
>   	if (ret) {
> @@ -278,6 +407,126 @@ int last_stage_init(void)
>   		}
>   	}
>   
> +	/* now check if modules are connected in supported mode */
> +
> +	for (i = 0; i < module_count; ++i) {
> +		switch (topology[i]) {
> +		case MOX_MODULE_SFP:
> +			if (sfp) {
> +				printf("Error: Only one SFP module is "
> +				       "supported!\n");

This gives checkpatch warnings:

WARNING: quoted string split across lines
#492: FILE: board/CZ.NIC/turris_mox/turris_mox.c:417:
+                               printf("Error: Only one SFP module is "
+                                      "supported!\n");

I don't have strong feeling here, but in general I also like the strings
not being split, as its better for grepping / searching the code.

BTW: Could you please change your patch subject for all those patches
to reflect the architecture. Something like this:

board: turris_mox: Check and configure modules
->
arm: mvebu: turris_mox: Check and configure modules

Thanks,
Stefan

> +			} else if (topaz) {
> +				printf("Error: SFP module cannot be connected "
> +				       "after Topaz Switch module!\n");
> +			} else {
> +				sfp_pos = i;
> +				++sfp;
> +			}
> +			break;
> +		case MOX_MODULE_PCI:
> +			if (pci) {
> +				printf("Error: Only one Mini-PCIe module is "
> +				       "supported!\n");
> +			} else if (usb) {
> +				printf("Error: Mini-PCIe module cannot come "
> +				       "after USB 3.0 module!\n");
> +			} else if (i && (i != 1 || !passpci)) {
> +				printf("Error: Mini-PCIe module should be the "
> +				       "first connected module or come right "
> +				       "after Passthrough Mini-PCIe module!\n");
> +			} else {
> +				++pci;
> +			}
> +			break;
> +		case MOX_MODULE_TOPAZ:
> +			if (topaz) {
> +				printf("Error: Only one Topaz module is "
> +				       "supported!\n");
> +			} else if (peridot >= 3) {
> +				printf("Error: At most two Peridot modules "
> +				       "can come before Topaz module!\n");
> +			} else {
> +				++topaz;
> +			}
> +			break;
> +		case MOX_MODULE_PERIDOT:
> +			if (sfp || topaz) {
> +				printf("Error: Peridot module must come before "
> +				       "SFP or Topaz module!\n");
> +			} else if (peridot >= 3) {
> +				printf("Error: At most three Peridot modules "
> +				       "are supported!\n");
> +			} else {
> +				peridot_pos[peridot] = i;
> +				++peridot;
> +			}
> +			break;
> +		case MOX_MODULE_USB3:
> +			if (pci) {
> +				printf("Error: USB 3.0 module cannot come "
> +				       "after Mini-PCIe module!\n");
> +			} else if (usb) {
> +				printf("Error: Only one USB 3.0 module is "
> +				       "supported!\n");
> +			} else if (i && (i != 1 || !passpci)) {
> +				printf("Error: USB 3.0 module should be the "
> +				       "first connected module or come right "
> +				       "after Passthrough Mini-PCIe module!\n");
> +			} else {
> +				++usb;
> +			}
> +			break;
> +		case MOX_MODULE_PASSPCI:
> +			if (passpci) {
> +				printf("Error: Only one Passthrough Mini-PCIe "
> +				       "module is supported!\n");
> +			} else if (i != 0) {
> +				printf("Error: Passthrough Mini-PCIe module "
> +				       "should be the first connected "
> +				       "module!\n");
> +			} else {
> +				++passpci;
> +			}
> +		}
> +	}
> +
> +	/* now configure modules */
> +
> +	if (get_reset_gpio(&reset_gpio) < 0)
> +		return 0;
> +
> +	if (peridot > 0) {
> +		if (configure_peridots(&reset_gpio) < 0) {
> +			printf("Cannot configure Peridot modules!\n");
> +			peridot = 0;
> +		}
> +	} else {
> +		dm_gpio_set_value(&reset_gpio, 1);
> +		mdelay(50);
> +		dm_gpio_set_value(&reset_gpio, 0);
> +		mdelay(50);
> +	}
> +
> +	if (peridot || topaz) {
> +		/*
> +		 * now check if the addresses are set by reading Scratch & Misc
> +		 * register 0x70 of Peridot (and potentially Topaz) modules
> +		 */
> +
> +		bus = miiphy_get_dev_by_name("neta at 30000");
> +		if (!bus) {
> +			printf("Cannot get MDIO bus device!\n");
> +		} else {
> +			for (i = 0; i < peridot; ++i)
> +				check_switch_address(bus, 0x10 + i);
> +
> +			if (topaz)
> +				check_switch_address(bus, 0x2);
> +
> +			sw_blink_leds(bus, peridot, topaz);
> +		}
> +	}
> +
>   	printf("\n");
>   
>   	return 0;
> 

Viele Grüße,
Stefan

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de


More information about the U-Boot mailing list