[U-Boot] [PATCH] net: macb: Clean 64b dma addresses if they are not detected

[Michal Simek]

On 21.9.2018 14:38, Nicolas Ferre wrote:
> Michal,
> 
> On 20/09/2018 at 08:23, Michal Simek wrote:
>> On 19.9.2018 20:08, Edgar E. Iglesias wrote:
>>> On Wed, Sep 19, 2018 at 06:08:18PM +0200, Michal Simek wrote:
>>>> Clear ADDR64 dma bit in DMACFG register in case that HW_DMA_CAP_64B
>>>> is not detected on 64bit system.
>>>> The issue was observed when bootloader(u-boot) does not check macb
>>>> feature at DCFG6 register (DAW64_OFFSET) and enabling 64bit dma support
>>>> by default. Then macb driver is reading DMACFG register back and only
>>>> adding 64bit dma configuration but not cleaning it out.
>>>>
>>>> This is also align with other features which are also cleared if
>>>> they are not
>>>> present.
>>>
>>> Hi Michal,
>>>
>>>>
>>>> Signed-off-by: Michal Simek <michal.simek at xilinx.com>
>>>> ---
>>>>
>>>>   drivers/net/ethernet/cadence/macb_main.c | 2 ++
>>>>   1 file changed, 2 insertions(+)
>>>>
>>>> diff --git a/drivers/net/ethernet/cadence/macb_main.c
>>>> b/drivers/net/ethernet/cadence/macb_main.c
>>>> index 16e4ef7d7185..79707dff3f13 100644
>>>> --- a/drivers/net/ethernet/cadence/macb_main.c
>>>> +++ b/drivers/net/ethernet/cadence/macb_main.c
>>>> @@ -2163,6 +2163,8 @@ static void macb_configure_dma(struct macb *bp)
>>>>   #ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
>>>>           if (bp->hw_dma_cap & HW_DMA_CAP_64B)
>>>>               dmacfg |= GEM_BIT(ADDR64);
>>>> +        else
>>>> +            dmacfg &= ~GEM_BIT(ADDR64);
>>>>   #endif
>>>
>>> I think you might want to do this clearing outside of the #ifdef.
>>> If CONFIG_ARCH_DMA_ADDR_T_64BIT is not defined, we'd want to make
>>> sure the ADDR64 is cleared. E.g something like:
>>>
>>>               dmacfg &= ~GEM_BIT(ADDR64);
>>> #ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
>>>               if (bp->hw_dma_cap & HW_DMA_CAP_64B)
>>>                       dmacfg |= GEM_BIT(ADDR64);
>>> #endif
>>>
>>>
>>> Same thing for the USE_HWSTAMP/PTP flags below.
>>
>> Origin patch, which introduce this read with mask,
>> macfg = gem_readl(bp, DMACFG) & ~GEM_BF(RXBS, -1L);
>> was done in 2011 and from that time this function was extended a little
>> bit. I am even not quite sure if make sense to read this reg and apply
>> setting on the top of it.
>>
>> Nicolas: Isn't it better simply compose that reg from scratch?
> 
> I have several arguments against composing this register from scratch:
> 
> 1/ the reset value of this register is non-null for both of our
> platforms and it could be meaningful to keep some of these values.
> 
> 2/ one bitfield could use different values between Zynq and AT91: RXBMS
> (1kB to 8kB for Zynq and 512 to 4KB for AT91), with same encoding.
> 
> 3/ and well, this is the type of register with multiple bits that are
> marked as "reserved" and that experience tells that they might be
> connected to something...
> 
> So, I'm all for correcting the code like what Edgar suggests.

ok. I have sent v2.

M