[U-Boot] [PATCH] gpio: mscc-bitbang-spi: Add a simple gpio driver for bitbgang spi
Daniel Schwierzeck
daniel.schwierzeck at gmail.com
Wed Sep 26 19:46:27 UTC 2018
On 25.09.2018 15:16, Gregory CLEMENT wrote:
> The VCore III SoCs such as the Luton but also the Ocelot can remap an SPI
> flash directly in memory. However, for writing in the flash the
> communication has to be done by software.
>
> Each of the signal used for the SPI are exposed in a single register. In
> order to be able to use the soft-spi driver, the management of this pin
> is done through this simple gpio driver.
>
> Even if the main purpose of this driver is to be used by soft-spi, it can
> still be used as a normal gpio driver but with limitation: for example
> the first pin can't be used as output.
>
> Signed-off-by: Gregory CLEMENT <gregory.clement at bootlin.com>
> ---
> drivers/gpio/Kconfig | 7 ++
> drivers/gpio/Makefile | 1 +
> drivers/gpio/gpio-mscc-bitbang-spi.c | 126 +++++++++++++++++++++++++++
> 3 files changed, 134 insertions(+)
> create mode 100644 drivers/gpio/gpio-mscc-bitbang-spi.c
>
> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> index 5cd8b34400..947a59cce3 100644
> --- a/drivers/gpio/Kconfig
> +++ b/drivers/gpio/Kconfig
> @@ -99,6 +99,13 @@ config LPC32XX_GPIO
> help
> Support for the LPC32XX GPIO driver.
>
> +config MSCC_BITBANG_SPI_GPIO
> + bool "Microsemi bitbang spi GPIO driver"
> + depends on DM_GPIO && SOC_VCOREIII
> + help
> + Support controlling the GPIO used for SPI bitbang by software. Can
> + be used by the VCoreIII SoCs, but it was mainly useful for Luton.
> +
> config MSM_GPIO
> bool "Qualcomm GPIO driver"
> depends on DM_GPIO
> diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> index f186120684..2085dd3cba 100644
> --- a/drivers/gpio/Makefile
> +++ b/drivers/gpio/Makefile
> @@ -58,3 +58,4 @@ obj-$(CONFIG_MVEBU_GPIO) += mvebu_gpio.o
> obj-$(CONFIG_MSM_GPIO) += msm_gpio.o
> obj-$(CONFIG_$(SPL_)PCF8575_GPIO) += pcf8575_gpio.o
> obj-$(CONFIG_PM8916_GPIO) += pm8916_gpio.o
> +obj-$(CONFIG_MSCC_BITBANG_SPI_GPIO) += gpio-mscc-bitbang-spi.o
> diff --git a/drivers/gpio/gpio-mscc-bitbang-spi.c b/drivers/gpio/gpio-mscc-bitbang-spi.c
> new file mode 100644
> index 0000000000..572107d010
> --- /dev/null
> +++ b/drivers/gpio/gpio-mscc-bitbang-spi.c
> @@ -0,0 +1,126 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Microsemi SoCs pinctrl driver
> + *
> + * Author: <gregory.clement at bootlin.com>
> + * License: Dual MIT/GPL
> + * Copyright (c) 2018 Microsemi Corporation
> + */
> +
> +#include <common.h>
> +#include <asm-generic/gpio.h>
> +#include <asm/io.h>
> +#include <dm.h>
> +#include <errno.h>
> +
> +enum {
> + SDI,
> + CS0,
> + CS1,
> + CS2,
> + CS3,
> + SDO,
> + SCK
> +};
> +
> +int pinmap[] = {0, 5, 6, 7, 8, 10, 12};
static const int?
> +
> +#define SW_SPI_CSn_OE 0x1E /* bits 1 to 4 */
> +#define SW_SPI_CS0_OE BIT(1)
> +#define SW_SPI_SDO_OE BIT(9)
> +#define SW_SPI_SCK_OE BIT(11)
> +#define SW_PIN_CTRL_MODE BIT(13)
> +
> +struct mscc_bb_spi_gpio {
> + u32 *regs;
void __iomem * ?
> + u32 cache_val;
> +};
> +
> +static int mscc_bb_spi_gpio_set(struct udevice *dev, unsigned oft, int val)
> +{
> + struct mscc_bb_spi_gpio *gpio = dev_get_priv(dev);
> +
> + if (val)
> + gpio->cache_val |= BIT(pinmap[oft]);
> + else
> + gpio->cache_val &= ~BIT(pinmap[oft]);
> +
> + writel(gpio->cache_val, gpio->regs);
> +
> + return 0;
> +}
> +
> +static int mscc_bb_spi_gpio_direction_output(struct udevice *dev, unsigned oft,
> + int val)
> +{
> + if (oft == 0) {
> + pr_err("SW_SPI_DSI can't be used as output\n");
> + return -ENOTSUPP;
> + }
> +
> + mscc_bb_spi_gpio_set(dev, oft, val);
> +
> + return 0;
> +}
> +
> +static int mscc_bb_spi_gpio_direction_input(struct udevice *dev, unsigned oft)
> +{
> + return 0;
> +}
> +
> +static int mscc_bb_spi_gpio_get(struct udevice *dev, unsigned int oft)
> +{
> + struct mscc_bb_spi_gpio *gpio = dev_get_priv(dev);
> + u32 val = readl(gpio->regs);
> +
> + return !!(val & BIT(pinmap[oft]));
> +}
> +
> +static const struct dm_gpio_ops mscc_bb_spi_gpio_ops = {
> + .direction_output = mscc_bb_spi_gpio_direction_output,
> + .direction_input = mscc_bb_spi_gpio_direction_input,
> + .set_value = mscc_bb_spi_gpio_set,
> + .get_value = mscc_bb_spi_gpio_get,
> +};
> +
> +static int mscc_bb_spi_gpio_probe(struct udevice *dev)
> +{
> + struct mscc_bb_spi_gpio *gpio = dev_get_priv(dev);
> + struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
> + fdt_addr_t addr;
> + fdt_size_t size;
> +
> + addr = devfdt_get_addr_size_index(dev, 0, &size);
> + if (addr == FDT_ADDR_T_NONE)
> + return -EINVAL;
> +
> + gpio->regs = ioremap(addr, size);
this sequence can be simplified with dev_remap_addr()
> +
> + uc_priv->bank_name = dev->name;
> + uc_priv->gpio_count = ARRAY_SIZE(pinmap);
> + /*
> + * Enable software mode to control the SPI pin, enables the
> + * output mode for most of the pin and initialize the cache
> + * value in the same time
> + */
> +
> + gpio->cache_val = SW_PIN_CTRL_MODE | SW_SPI_SCK_OE | SW_SPI_SDO_OE |
> + SW_SPI_CS0_OE;
> + writel(gpio->cache_val, gpio->regs);
> +
> + return 0;
> +}
> +
> +static const struct udevice_id mscc_bb_spi_gpio_ids[] = {
> + { .compatible = "mscc,spi-bitbang-gpio" },
> + { }
> +};
> +
> +U_BOOT_DRIVER(gpio_mscc_bb_spi) = {
> + .name = "gpio-mscc-spi-bitbang",
> + .id = UCLASS_GPIO,
> + .ops = &mscc_bb_spi_gpio_ops,
> + .probe = mscc_bb_spi_gpio_probe,
> + .of_match = of_match_ptr(mscc_bb_spi_gpio_ids),
> + .priv_auto_alloc_size = sizeof(struct mscc_bb_spi_gpio),
> +};
>
--
- Daniel
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180926/fa3e87a0/attachment.sig>
More information about the U-Boot
mailing list