[U-Boot] [PATCH] imx: Extend PCL063 support for phyCORE-i.MX6ULL SOM
Parthiban Nallathambi
parthitce at gmail.com
Sun Apr 7 17:56:54 UTC 2019
Extend PHYTEC phyBOARD-i.MX6UL for phyCORE-i.MX6UL SoM (PCL063)
with eMMC on SoM.
CPU: Freescale i.MX6ULL rev1.0 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 38C
Reset cause: POR
Model: Phytec phyBOARD-i.MX6ULL-Segin SBC
Board: PHYTEC phyCORE-i.MX6ULL
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial at 02020000
Out: serial at 02020000
Err: serial at 02020000
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- eMMC
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Parthiban Nallathambi <parthitce at gmail.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/imx6ul-phycore-segin.dts | 3 +-
arch/arm/dts/imx6ull-phycore-segin.dts | 81 ++++++++++++
...{imx6ul-pcl063.dtsi => pcl063-common.dtsi} | 31 ++++-
arch/arm/mach-imx/mx6/Kconfig | 12 ++
board/phytec/pcl063/Kconfig | 13 ++
board/phytec/pcl063/MAINTAINERS | 6 +-
board/phytec/pcl063/pcl063.c | 5 +-
board/phytec/pcl063/spl.c | 76 +++++++++++-
configs/phycore_pcl063_ull_defconfig | 54 ++++++++
include/configs/pcl063_ull.h | 117 ++++++++++++++++++
11 files changed, 388 insertions(+), 11 deletions(-)
create mode 100644 arch/arm/dts/imx6ull-phycore-segin.dts
rename arch/arm/dts/{imx6ul-pcl063.dtsi => pcl063-common.dtsi} (84%)
create mode 100644 configs/phycore_pcl063_ull_defconfig
create mode 100644 include/configs/pcl063_ull.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 0e2ffdb87f..431afb915f 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -539,6 +539,7 @@ dtb-$(CONFIG_MX6UL) += \
dtb-$(CONFIG_MX6ULL) += \
imx6ull-14x14-evk.dtb \
imx6ull-colibri.dtb \
+ imx6ull-phycore-segin.dtb
dtb-$(CONFIG_MX7) += imx7d-sdb.dtb \
imx7d-sdb-qspi.dtb \
diff --git a/arch/arm/dts/imx6ul-phycore-segin.dts b/arch/arm/dts/imx6ul-phycore-segin.dts
index a46012e2b4..9e6984e137 100644
--- a/arch/arm/dts/imx6ul-phycore-segin.dts
+++ b/arch/arm/dts/imx6ul-phycore-segin.dts
@@ -16,7 +16,8 @@
/dts-v1/;
-#include "imx6ul-pcl063.dtsi"
+#include "imx6ul.dtsi"
+#include "pcl063-common.dtsi"
/ {
model = "Phytec phyBOARD-i.MX6UL-Segin SBC";
diff --git a/arch/arm/dts/imx6ull-phycore-segin.dts b/arch/arm/dts/imx6ull-phycore-segin.dts
new file mode 100644
index 0000000000..c20a867c90
--- /dev/null
+++ b/arch/arm/dts/imx6ull-phycore-segin.dts
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce at gmail.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+
+#include "imx6ull.dtsi"
+#include "pcl063-common.dtsi"
+
+/ {
+ model = "Phytec phyBOARD-i.MX6ULL-Segin SBC";
+ compatible = "phytec,phyboard-imx6ull-segin", "phytec,imx6ull-pcl063",
+ "fsl,imx6ull";
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&i2c1 {
+ i2c_rtc: rtc at 68 {
+ compatible = "microcrystal,rv4162";
+ reg = <0x68>;
+ status = "okay";
+ };
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usdhc2 {
+ status = "okay";
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1_id>;
+ dr_mode = "otg";
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1
+ MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x1b0b1
+ MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1_id: usbotg1idgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059
+ >;
+ };
+
+};
diff --git a/arch/arm/dts/imx6ul-pcl063.dtsi b/arch/arm/dts/pcl063-common.dtsi
similarity index 84%
rename from arch/arm/dts/imx6ul-pcl063.dtsi
rename to arch/arm/dts/pcl063-common.dtsi
index 24a6a47983..f505f62230 100644
--- a/arch/arm/dts/imx6ul-pcl063.dtsi
+++ b/arch/arm/dts/pcl063-common.dtsi
@@ -7,10 +7,6 @@
* Author: Christian Hemp <c.hemp at phytec.de>
*/
-/dts-v1/;
-
-#include "imx6ul.dtsi"
-
/ {
model = "Phytec phyCORE-i.MX6 Ultra Lite SOM";
compatible = "phytec,imx6ul-pcl063", "fsl,imx6ul";
@@ -99,6 +95,18 @@
status = "okay";
};
+&usdhc2 {
+ u-boot,dm-spl;
+ u-boot,dm-pre-reloc;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <8>;
+ no-1-8-v;
+ non-removable;
+ keep-power-in-suspend;
+ status = "disabled";
+};
+
&iomuxc {
pinctrl-names = "default";
@@ -170,4 +178,19 @@
>;
};
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9
+ >;
+ };
};
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index e782859b1e..5e2f08e500 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -443,6 +443,18 @@ config TARGET_PCL063
select DM_THERMAL
select SUPPORT_SPL
+config TARGET_PCL063_ULL
+ bool "PHYTEC PCL063 (phyCORE-i.MX6ULL)"
+ select MX6ULL
+ select DM
+ select DM_ETH
+ select DM_GPIO
+ select DM_I2C
+ select DM_MMC
+ select DM_SERIAL
+ select DM_THERMAL
+ select SUPPORT_SPL
+
config TARGET_SECOMX6
bool "secomx6 boards"
diff --git a/board/phytec/pcl063/Kconfig b/board/phytec/pcl063/Kconfig
index 977db70f64..58f72f2791 100644
--- a/board/phytec/pcl063/Kconfig
+++ b/board/phytec/pcl063/Kconfig
@@ -10,3 +10,16 @@ config SYS_CONFIG_NAME
default "pcl063"
endif
+
+if TARGET_PCL063_ULL
+
+config SYS_BOARD
+ default "pcl063"
+
+config SYS_VENDOR
+ default "phytec"
+
+config SYS_CONFIG_NAME
+ default "pcl063_ull"
+
+endif
diff --git a/board/phytec/pcl063/MAINTAINERS b/board/phytec/pcl063/MAINTAINERS
index c65a951f3d..70e03cfe71 100644
--- a/board/phytec/pcl063/MAINTAINERS
+++ b/board/phytec/pcl063/MAINTAINERS
@@ -1,8 +1,12 @@
PCL063 BOARD
M: Martyn Welch <martyn.welch at collabora.com>
+M: Parthiban Nallathambi <parthitce at gmail.com>
S: Maintained
-F: arch/arm/dts/imx6ul-pcl063.dtsi
F: arch/arm/dts/imx6ul-phycore-segin.dts
+F: arch/arm/dts/imx6ull-phycore-segin.dts
+F: arch/arm/dts/pcl063-common.dtsi
F: board/phytec/pcl063/
F: configs/phycore_pcl063_defconfig
+F: configs/phycore_pcl063_ull_defconfig
F: include/configs/pcl063.h
+F: include/configs/pcl063_ull.h
diff --git a/board/phytec/pcl063/pcl063.c b/board/phytec/pcl063/pcl063.c
index 38b233d1b0..17012df037 100644
--- a/board/phytec/pcl063/pcl063.c
+++ b/board/phytec/pcl063/pcl063.c
@@ -200,7 +200,10 @@ int board_init(void)
int checkboard(void)
{
- puts("Board: PHYTEC phyCORE-i.MX6UL\n");
+ u32 cpurev = get_cpu_rev();
+
+ printf("Board: PHYTEC phyCORE-i.MX%s\n",
+ get_imx_type((cpurev & 0xFF000) >> 12));
return 0;
}
diff --git a/board/phytec/pcl063/spl.c b/board/phytec/pcl063/spl.c
index b93cd493f2..73a774645d 100644
--- a/board/phytec/pcl063/spl.c
+++ b/board/phytec/pcl063/spl.c
@@ -13,6 +13,7 @@
#include <asm/arch/mx6-ddr.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/crm_regs.h>
+#include <asm/arch/sys_proto.h>
#include <fsl_esdhc.h>
/* Configuration for Micron MT41K256M16TW-107 IT:P, 32M x 16 x 8 -> 256MiB */
@@ -117,11 +118,32 @@ static iomux_v3_cfg_t const usdhc1_pads[] = {
MX6_PAD_UART1_RTS_B__USDHC1_CD_B | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};
+#ifndef CONFIG_NAND_MXS
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+#endif
+
static struct fsl_esdhc_cfg usdhc_cfg[] = {
{
.esdhc_base = USDHC1_BASE_ADDR,
.max_bus_width = 4,
},
+#ifndef CONFIG_NAND_MXS
+ {
+ .esdhc_base = USDHC2_BASE_ADDR,
+ .max_bus_width = 8,
+ },
+#endif
};
int board_mmc_getcd(struct mmc *mmc)
@@ -131,12 +153,58 @@ int board_mmc_getcd(struct mmc *mmc)
int board_mmc_init(bd_t *bis)
{
- imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
-
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+ int i, ret;
+
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ SETUP_IOMUX_PADS(usdhc1_pads);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+#ifndef CONFIG_NAND_MXS
+ case 1:
+ SETUP_IOMUX_PADS(usdhc2_pads);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+#endif
+ default:
+ printf("Warning - USDHC%d controller not supporting\n",
+ i + 1);
+ return 0;
+ }
+
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ if (ret) {
+ printf("Warning: failed to initialize mmc dev %d\n", i);
+ return ret;
+ }
+ }
+
+ return 0;
}
+void board_boot_order(u32 *spl_boot_list)
+{
+ u32 bmode = imx6_src_get_boot_mode();
+ u8 boot_dev = BOOT_DEVICE_MMC1;
+
+ switch ((bmode & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
+ case IMX6_BMODE_SD:
+ case IMX6_BMODE_ESD:
+ boot_dev = BOOT_DEVICE_MMC1;
+ break;
+ case IMX6_BMODE_MMC:
+ case IMX6_BMODE_EMMC:
+ boot_dev = BOOT_DEVICE_MMC2;
+ break;
+ default:
+ /* Default - BOOT_DEVICE_MMC1 */
+ printf("Wrong board boot order\n");
+ break;
+ }
+
+ spl_boot_list[0] = boot_dev;
+}
#endif /* CONFIG_FSL_ESDHC */
void board_init_f(ulong dummy)
diff --git a/configs/phycore_pcl063_ull_defconfig b/configs/phycore_pcl063_ull_defconfig
new file mode 100644
index 0000000000..75408a8344
--- /dev/null
+++ b/configs/phycore_pcl063_ull_defconfig
@@ -0,0 +1,54 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x87800000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_TARGET_PCL063_ULL=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL=y
+# CONFIG_CMD_DEKBLOB is not set
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_NR_DRAM_BANKS=8
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_BOOTDELAY=3
+# CONFIG_USE_BOOTCOMMAND is not set
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_USB_HOST_SUPPORT=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+# CONFIG_RANDOM_UUID is not set
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_SDP=y
+CONFIG_CMD_CACHE=y
+# CONFIG_ISO_PARTITION is not set
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6ull-phycore-segin"
+CONFIG_DM_I2C_GPIO=y
+CONFIG_SYS_I2C_MXC=y
+CONFIG_FSL_ESDHC=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_MICREL=y
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_MXC_UART=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Phytec"
+CONFIG_USB_GADGET_VENDOR_NUM=0x01b67
+CONFIG_USB_GADGET_PRODUCT_NUM=0x4fff
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_LZO=y
diff --git a/include/configs/pcl063_ull.h b/include/configs/pcl063_ull.h
new file mode 100644
index 0000000000..0f1a010b4e
--- /dev/null
+++ b/include/configs/pcl063_ull.h
@@ -0,0 +1,117 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Board configuration file for Phytec phyBOARD-i.MX6ULL-Segin SBC
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce at gmail.com>
+ *
+ * Based on include/configs/xpress.h:
+ * Copyright (C) 2015-2016 Stefan Roese <sr at denx.de>
+ */
+#ifndef __PCL063_ULL_H
+#define __PCL063_ULL_H
+
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+/* SPL options */
+#include "imx6_spl.h"
+
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M)
+
+/* Environment settings */
+#define CONFIG_ENV_SIZE (0x4000)
+#define CONFIG_ENV_OFFSET (0x80000)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_OFFSET_REDUND \
+ (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+
+/* Environment in SD */
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_SYS_MMC_ENV_PART 0
+#define MMC_ROOTFS_DEV 0
+#define MMC_ROOTFS_PART 2
+
+/* Console configs */
+#define CONFIG_MXC_UART_BASE UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_FSL_USDHC
+
+#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+/* I2C configs */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_SPEED 100000
+#endif
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x10000000)
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_SYS_HZ 1000
+
+/* Physical Memory Map */
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE SZ_256M
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* NAND */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x40000000
+
+/* USB Configs */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
+
+#define CONFIG_IMX_THERMAL
+
+#define ENV_MMC \
+ "mmcdev=" __stringify(MMC_ROOTFS_DEV) "\0" \
+ "mmcpart=" __stringify(MMC_ROOTFS_PART) "\0" \
+ "fitpart=1\0" \
+ "bootdelay=3\0" \
+ "silent=1\0" \
+ "optargs=rw rootwait\0" \
+ "mmcautodetect=yes\0" \
+ "mmcrootfstype=ext4\0" \
+ "mmcfit_name=fitImage\0" \
+ "mmcloadfit=fatload mmc ${mmcdev}:${fitpart} ${fit_addr} " \
+ "${mmcfit_name}\0" \
+ "mmcargs=setenv bootargs " \
+ "root=/dev/mmcblk${mmcdev}p${mmcpart} ${optargs} " \
+ "console=${console} rootfstype=${mmcrootfstype}\0" \
+ "mmc_mmc_fit=run mmcloadfit;run mmcargs addcon; bootm ${fit_addr}\0" \
+
+/* Default environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "fdt_high=0xffffffff\0" \
+ "console=ttymxc0,115200n8\0" \
+ "addcon=setenv bootargs ${bootargs} console=${console},${baudrate}\0" \
+ "fit_addr=0x82000000\0" \
+ ENV_MMC
+
+#define CONFIG_BOOTCOMMAND "run mmc_mmc_fit"
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(MMC, mmc, 1) \
+ func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+
+#endif /* __PCL063_ULL_H */
--
2.17.2
More information about the U-Boot
mailing list