[U-Boot] [PATCH RESEND 10/10] imx: support i.MX8QM MEK board
Peng Fan
peng.fan at nxp.com
Tue Apr 9 12:48:32 UTC 2019
Hi Stefano, Fabio
Any comments on this patchset?
Thanks,
Peng.
> -----Original Message-----
> From: Peng Fan [mailto:peng.fan at nxp.com]
> Sent: 2019年3月5日 10:33
> To: sbabic at denx.de; Fabio Estevam <fabio.estevam at nxp.com>
> Cc: u-boot at lists.denx.de; van.freenix at gmail.com; dl-uboot-imx
> <uboot-imx at nxp.com>; Peng Fan <peng.fan at nxp.com>
> Subject: [PATCH RESEND 10/10] imx: support i.MX8QM MEK board
>
> Add i.MX8QM MEK board support.
> Included a basic dts, enabled SPL FIT
>
> Boot log as below:
> U-Boot SPL 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)
> Normal Boot Trying to boot from MMC2_2
>
> U-Boot 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)
>
> CPU: NXP i.MX8QM RevB A53 at 142933 MHz
>
> Model: Freescale i.MX8QM MEK
> Board: iMX8QM MEK
> Build: SCFW 9330215b
> Boot: SD1
> DRAM: 6 GiB
> MMC: FSL_SDHC: 0, FSL_SDHC: 1
> Loading Environment from MMC... *** Warning - bad CRC, using default
> environment
>
> In: serial at 5a060000
> Out: serial at 5a060000
> Err: serial at 5a060000
> Net:
> Error: ethernet at 5b040000 address not set.
> eth-1: ethernet at 5b040000
> Hit any key to stop autoboot: 0
>
> Signed-off-by: Peng Fan <peng.fan at nxp.com>
> ---
> arch/arm/dts/Makefile | 4 +-
> arch/arm/dts/fsl-imx8qm-mek-u-boot.dtsi | 112 +++++++++++++++++++
> arch/arm/dts/fsl-imx8qm-mek.dts | 184
> ++++++++++++++++++++++++++++++++
> arch/arm/mach-imx/imx8/Kconfig | 6 ++
> board/freescale/imx8qm_mek/Kconfig | 14 +++
> board/freescale/imx8qm_mek/MAINTAINERS | 6 ++
> board/freescale/imx8qm_mek/Makefile | 8 ++
> board/freescale/imx8qm_mek/README | 57 ++++++++++
> board/freescale/imx8qm_mek/imx8qm_mek.c | 157
> +++++++++++++++++++++++++++
> board/freescale/imx8qm_mek/imximage.cfg | 19 ++++
> board/freescale/imx8qm_mek/spl.c | 75 +++++++++++++
> configs/imx8qm_mek_defconfig | 75 +++++++++++++
> include/configs/imx8qm_mek.h | 176
> ++++++++++++++++++++++++++++++
> 13 files changed, 892 insertions(+), 1 deletion(-) create mode 100644
> arch/arm/dts/fsl-imx8qm-mek-u-boot.dtsi
> create mode 100644 arch/arm/dts/fsl-imx8qm-mek.dts create mode
> 100644 board/freescale/imx8qm_mek/Kconfig
> create mode 100644 board/freescale/imx8qm_mek/MAINTAINERS
> create mode 100644 board/freescale/imx8qm_mek/Makefile
> create mode 100644 board/freescale/imx8qm_mek/README create mode
> 100644 board/freescale/imx8qm_mek/imx8qm_mek.c
> create mode 100644 board/freescale/imx8qm_mek/imximage.cfg
> create mode 100644 board/freescale/imx8qm_mek/spl.c create mode
> 100644 configs/imx8qm_mek_defconfig create mode 100644
> include/configs/imx8qm_mek.h
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index
> 2a040b20a5..954d595391 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -486,7 +486,9 @@ dtb-$(CONFIG_MX7) += imx7d-sdb.dtb \
>
> dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-evk.dtb
>
> -dtb-$(CONFIG_ARCH_IMX8) += fsl-imx8qxp-mek.dtb
> +dtb-$(CONFIG_ARCH_IMX8) += \
> + fsl-imx8qxp-mek.dtb \
> + fsl-imx8qm-mek.dtb \
>
> dtb-$(CONFIG_ARCH_IMX8M) += fsl-imx8mq-evk.dtb
>
> diff --git a/arch/arm/dts/fsl-imx8qm-mek-u-boot.dtsi
> b/arch/arm/dts/fsl-imx8qm-mek-u-boot.dtsi
> new file mode 100644
> index 0000000000..5d50eb028e
> --- /dev/null
> +++ b/arch/arm/dts/fsl-imx8qm-mek-u-boot.dtsi
> @@ -0,0 +1,112 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright 2018 NXP
> + */
> +
> +&mu {
> + u-boot,dm-spl;
> +};
> +
> +&clk {
> + u-boot,dm-spl;
> +};
> +
> +&iomuxc {
> + u-boot,dm-spl;
> +};
> +
> +&pd_lsio {
> + u-boot,dm-spl;
> +};
> +
> +&pd_lsio_gpio0 {
> + u-boot,dm-spl;
> +};
> +
> +&pd_lsio_gpio1 {
> + u-boot,dm-spl;
> +};
> +
> +&pd_lsio_gpio2 {
> + u-boot,dm-spl;
> +};
> +
> +&pd_lsio_gpio3 {
> + u-boot,dm-spl;
> +};
> +
> +&pd_lsio_gpio4 {
> + u-boot,dm-spl;
> +};
> +
> +&pd_lsio_gpio5 {
> + u-boot,dm-spl;
> +};
> +
> +&pd_lsio_gpio6 {
> + u-boot,dm-spl;
> +};
> +
> +&pd_lsio_gpio7 {
> + u-boot,dm-spl;
> +};
> +
> +&pd_conn {
> + u-boot,dm-spl;
> +};
> +
> +&pd_conn_sdch0 {
> + u-boot,dm-spl;
> +};
> +
> +&pd_conn_sdch1 {
> + u-boot,dm-spl;
> +};
> +
> +&pd_conn_sdch2 {
> + u-boot,dm-spl;
> +};
> +
> +&gpio0 {
> + u-boot,dm-spl;
> +};
> +
> +&gpio1 {
> + u-boot,dm-spl;
> +};
> +
> +&gpio2 {
> + u-boot,dm-spl;
> +};
> +
> +&gpio3 {
> + u-boot,dm-spl;
> +};
> +
> +&gpio4 {
> + u-boot,dm-spl;
> +};
> +
> +&gpio5 {
> + u-boot,dm-spl;
> +};
> +
> +&gpio6 {
> + u-boot,dm-spl;
> +};
> +
> +&gpio7 {
> + u-boot,dm-spl;
> +};
> +
> +&lpuart0 {
> + u-boot,dm-spl;
> +};
> +
> +&usdhc1 {
> + u-boot,dm-spl;
> +};
> +
> +&usdhc2 {
> + u-boot,dm-spl;
> +};
> diff --git a/arch/arm/dts/fsl-imx8qm-mek.dts
> b/arch/arm/dts/fsl-imx8qm-mek.dts new file mode 100644 index
> 0000000000..63908ba6bf
> --- /dev/null
> +++ b/arch/arm/dts/fsl-imx8qm-mek.dts
> @@ -0,0 +1,184 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright 2017-2018 NXP
> + */
> +
> +/dts-v1/;
> +
> +#include "fsl-imx8qm.dtsi"
> +#include "fsl-imx8qm-mek-u-boot.dtsi"
> +
> +/ {
> + model = "Freescale i.MX8QM MEK";
> + compatible = "fsl,imx8qm-mek", "fsl,imx8qm";
> +
> + chosen {
> + bootargs = "console=ttyLP0,115200
> earlycon=lpuart32,0x5a060000,115200";
> + stdout-path = &lpuart0;
> + };
> +
> + reg_usdhc2_vmmc: usdhc2_vmmc {
> + compatible = "regulator-fixed";
> + regulator-name = "sw-3p3-sd1";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio4 7 GPIO_ACTIVE_HIGH>;
> + off-on-delay = <4800>;
> + enable-active-high;
> + };
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
> +
> + imx8qm-mek {
> + pinctrl_hog: hoggrp {
> + fsl,pins = <
> + SC_P_MCLK_OUT0_AUD_ACM_MCLK_OUT0
> 0x0600004c
> + SC_P_QSPI1A_DATA1_LSIO_GPIO4_IO25 0x0600004c
> + SC_P_SCU_GPIO0_03_LSIO_GPIO0_IO31 0x0600004c
> + >;
> + };
> +
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <
> + SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD
> 0x000014a0
> + SC_P_ENET0_MDC_CONN_ENET0_MDC
> 0x06000020
> + SC_P_ENET0_MDIO_CONN_ENET0_MDIO
> 0x06000020
> +
> SC_P_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL
> 0x00000061
> + SC_P_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC
> 0x00000061
> + SC_P_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0
> 0x00000061
> + SC_P_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1
> 0x00000061
> + SC_P_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2
> 0x00000061
> + SC_P_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3
> 0x00000061
> + SC_P_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC
> 0x00000061
> +
> SC_P_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL
> 0x00000061
> + SC_P_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0
> 0x00000061
> + SC_P_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1
> 0x00000061
> + SC_P_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2
> 0x00000061
> + SC_P_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3
> 0x00000061
> + >;
> + };
> +
> + pinctrl_fec2: fec2grp {
> + fsl,pins = <
> + SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD
> 0x000014a0
> +
> SC_P_ENET1_RGMII_TX_CTL_CONN_ENET1_RGMII_TX_CTL
> 0x00000060
> + SC_P_ENET1_RGMII_TXC_CONN_ENET1_RGMII_TXC
> 0x00000060
> + SC_P_ENET1_RGMII_TXD0_CONN_ENET1_RGMII_TXD0
> 0x00000060
> + SC_P_ENET1_RGMII_TXD1_CONN_ENET1_RGMII_TXD1
> 0x00000060
> + SC_P_ENET1_RGMII_TXD2_CONN_ENET1_RGMII_TXD2
> 0x00000060
> + SC_P_ENET1_RGMII_TXD3_CONN_ENET1_RGMII_TXD3
> 0x00000060
> + SC_P_ENET1_RGMII_RXC_CONN_ENET1_RGMII_RXC
> 0x00000060
> +
> SC_P_ENET1_RGMII_RX_CTL_CONN_ENET1_RGMII_RX_CTL
> 0x00000060
> + SC_P_ENET1_RGMII_RXD0_CONN_ENET1_RGMII_RXD0
> 0x00000060
> + SC_P_ENET1_RGMII_RXD1_CONN_ENET1_RGMII_RXD1
> 0x00000060
> + SC_P_ENET1_RGMII_RXD2_CONN_ENET1_RGMII_RXD2
> 0x00000060
> + SC_P_ENET1_RGMII_RXD3_CONN_ENET1_RGMII_RXD3
> 0x00000060
> + >;
> + };
> +
> + pinctrl_lpuart0: lpuart0grp {
> + fsl,pins = <
> + SC_P_UART0_RX_DMA_UART0_RX 0x06000020
> + SC_P_UART0_TX_DMA_UART0_TX 0x06000020
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + SC_P_EMMC0_CLK_CONN_EMMC0_CLK
> 0x06000041
> + SC_P_EMMC0_CMD_CONN_EMMC0_CMD
> 0x00000021
> + SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0
> 0x00000021
> + SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1
> 0x00000021
> + SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2
> 0x00000021
> + SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3
> 0x00000021
> + SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4
> 0x00000021
> + SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5
> 0x00000021
> + SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6
> 0x00000021
> + SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7
> 0x00000021
> + SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE
> 0x00000041
> + SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B
> 0x00000021
> + >;
> + };
> +
> + pinctrl_usdhc2_gpio: usdhc2grpgpio {
> + fsl,pins = <
> + SC_P_USDHC1_DATA6_LSIO_GPIO5_IO21 0x00000021
> + SC_P_USDHC1_DATA7_LSIO_GPIO5_IO22 0x00000021
> + SC_P_USDHC1_RESET_B_LSIO_GPIO4_IO07
> 0x00000021
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + SC_P_USDHC1_CLK_CONN_USDHC1_CLK
> 0x06000041
> + SC_P_USDHC1_CMD_CONN_USDHC1_CMD
> 0x00000021
> + SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0
> 0x00000021
> + SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1
> 0x00000021
> + SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2
> 0x00000021
> + SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3
> 0x00000021
> + SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT
> 0x00000021
> + >;
> + };
> + };
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> + bus-width = <4>;
> + cd-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
> + wp-gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>;
> + vmmc-supply = <®_usdhc2_vmmc>;
> + status = "okay";
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> + phy-mode = "rgmii-txid";
> + phy-handle = <ðphy0>;
> + fsl,magic-packet;
> + fsl,rgmii_rxc_dly;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy at 0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + at803x,eee-disabled;
> + at803x,vddio-1p8v;
> + };
> +
> + ethphy1: ethernet-phy at 1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + at803x,eee-disabled;
> + at803x,vddio-1p8v;
> + status = "disabled";
> + };
> + };
> +};
> +
> +&lpuart0 { /* console */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lpuart0>;
> + status = "okay";
> +};
> +
> +&gpio1 {
> + status = "okay";
> +};
> diff --git a/arch/arm/mach-imx/imx8/Kconfig
> b/arch/arm/mach-imx/imx8/Kconfig index 4336a8c236..c32f7dbb61 100644
> --- a/arch/arm/mach-imx/imx8/Kconfig
> +++ b/arch/arm/mach-imx/imx8/Kconfig
> @@ -32,8 +32,14 @@ config TARGET_IMX8QXP_MEK
> select BOARD_LATE_INIT
> select IMX8QXP
>
> +config TARGET_IMX8QM_MEK
> + bool "Support i.MX8QM MEK board"
> + select BOARD_LATE_INIT
> + select IMX8QM
> +
> endchoice
>
> source "board/freescale/imx8qxp_mek/Kconfig"
> +source "board/freescale/imx8qm_mek/Kconfig"
>
> endif
> diff --git a/board/freescale/imx8qm_mek/Kconfig
> b/board/freescale/imx8qm_mek/Kconfig
> new file mode 100644
> index 0000000000..93d7d5f9c5
> --- /dev/null
> +++ b/board/freescale/imx8qm_mek/Kconfig
> @@ -0,0 +1,14 @@
> +if TARGET_IMX8QM_MEK
> +
> +config SYS_BOARD
> + default "imx8qm_mek"
> +
> +config SYS_VENDOR
> + default "freescale"
> +
> +config SYS_CONFIG_NAME
> + default "imx8qm_mek"
> +
> +source "board/freescale/common/Kconfig"
> +
> +endif
> diff --git a/board/freescale/imx8qm_mek/MAINTAINERS
> b/board/freescale/imx8qm_mek/MAINTAINERS
> new file mode 100644
> index 0000000000..115830df19
> --- /dev/null
> +++ b/board/freescale/imx8qm_mek/MAINTAINERS
> @@ -0,0 +1,6 @@
> +i.MX8QM MEK BOARD
> +M: Peng Fan <peng.fan at nxp.com>
> +S: Maintained
> +F: board/freescale/imx8qm_mek/
> +F: include/configs/imx8qm_mek.h
> +F: configs/imx8qm_mek_defconfig
> diff --git a/board/freescale/imx8qm_mek/Makefile
> b/board/freescale/imx8qm_mek/Makefile
> new file mode 100644
> index 0000000000..bc9a1260bd
> --- /dev/null
> +++ b/board/freescale/imx8qm_mek/Makefile
> @@ -0,0 +1,8 @@
> +#
> +# Copyright 2018 NXP
> +#
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +
> +obj-y += imx8qm_mek.o
> +obj-$(CONFIG_SPL_BUILD) += spl.o
> diff --git a/board/freescale/imx8qm_mek/README
> b/board/freescale/imx8qm_mek/README
> new file mode 100644
> index 0000000000..c3523801ae
> --- /dev/null
> +++ b/board/freescale/imx8qm_mek/README
> @@ -0,0 +1,57 @@
> +U-Boot for the NXP i.MX8QM EVK board
> +
> +Quick Start
> +===========
> +
> +- Build the ARM Trusted firmware binary
> +- Get scfw_tcm.bin and ahab-container.img
> +- Build U-Boot
> +- Flash the binary into the SD card
> +- Boot
> +
> +Get and Build the ARM Trusted firmware
> +======================================
> +
> +$ git clone https://source.codeaurora.org/external/imx/imx-atf
> +$ cd imx-atf/
> +$ git checkout origin/imx_4.14.78_1.0.0_ga -b imx_4.14.78_1.0.0_ga $
> +make PLAT=imx8qm bl31
> +
> +Get scfw_tcm.bin and ahab-container.img
> ==============================
> +
> +$ wget
> +https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-sc-firmware-1.1.bin
> +$ chmod +x imx-sc-firmware-1.1.bin
> +$ ./imx-sc-firmware-1.1.bin
> +$ wget
> https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin
> +$ chmod +x firmware-imx-8.0.bin
> +$ ./firmware-imx-8.0.bin
> +
> +Copy the following binaries to U-Boot folder:
> +
> +$ cp imx-atf/build/imx8qm/release/bl31.bin .
> +$ cp u-boot/u-boot.bin .
> +
> +Copy the following firmwares U-Boot folder :
> +
> +$ cp firmware-imx-7.6/firmware/seco/ahab-container.img .
> +$ cp imx-sc-firmware-0.7/mx8qm-mek-scfw-tcm.bin .
> +
> +Build U-Boot
> +============
> +$ export ATF_LOAD_ADDR=0x80000000
> +$ export BL33_LOAD_ADDR=0x80020000
> +$ make imx8qm_mek_defconfig
> +$ make flash.bin
> +$ dd if=u-boot.itb of=flash.bin bs=512 seek=1984
> +
> +Flash the binary into the SD card
> +=================================
> +
> +Burn the flash.bin binary to SD card offset 32KB:
> +
> +$ sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32
> +
> +Boot
> +====
> +Set Boot switch SW2: 1100.
> diff --git a/board/freescale/imx8qm_mek/imx8qm_mek.c
> b/board/freescale/imx8qm_mek/imx8qm_mek.c
> new file mode 100644
> index 0000000000..e69efc4dd6
> --- /dev/null
> +++ b/board/freescale/imx8qm_mek/imx8qm_mek.c
> @@ -0,0 +1,157 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright 2018 NXP
> + */
> +
> +#include <common.h>
> +#include <errno.h>
> +#include <linux/libfdt.h>
> +#include <environment.h>
> +#include <asm/io.h>
> +#include <asm/gpio.h>
> +#include <asm/arch/clock.h>
> +#include <asm/arch/sci/sci.h>
> +#include <asm/arch/imx8-pins.h>
> +#include <asm/arch/iomux.h>
> +#include <asm/arch/sys_proto.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN <<
> PADRING_CONFIG_SHIFT) | \
> + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
> + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) |
> \
> + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
> +
> +static iomux_cfg_t uart0_pads[] = {
> + SC_P_UART0_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
> + SC_P_UART0_TX | MUX_PAD_CTRL(UART_PAD_CTRL), };
> +
> +static void setup_iomux_uart(void)
> +{
> + imx8_iomux_setup_multiple_pads(uart0_pads,
> ARRAY_SIZE(uart0_pads)); }
> +
> +int board_early_init_f(void)
> +{
> + int ret;
> + /* Set UART0 clock root to 80 MHz */
> + sc_pm_clock_rate_t rate = 80000000;
> +
> + /* Power up UART0 */
> + ret = sc_pm_set_resource_power_mode(-1, SC_R_UART_0,
> SC_PM_PW_MODE_ON);
> + if (ret)
> + return ret;
> +
> + ret = sc_pm_set_clock_rate(-1, SC_R_UART_0, 2, &rate);
> + if (ret)
> + return ret;
> +
> + /* Enable UART0 clock root */
> + ret = sc_pm_clock_enable(-1, SC_R_UART_0, 2, true, false);
> + if (ret)
> + return ret;
> +
> + setup_iomux_uart();
> +
> + sc_pm_set_resource_power_mode(-1, SC_R_GPIO_5,
> SC_PM_PW_MODE_ON);
> +
> + return 0;
> +}
> +
> +#if IS_ENABLED(CONFIG_DM_GPIO)
> +static void board_gpio_init(void)
> +{
> + /* TODO */
> +}
> +#else
> +static inline void board_gpio_init(void) {} #endif
> +
> +#if IS_ENABLED(CONFIG_FEC_MXC)
> +#include <miiphy.h>
> +
> +int board_phy_config(struct phy_device *phydev) {
> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
> +
> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00);
> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
> +
> + if (phydev->drv->config)
> + phydev->drv->config(phydev);
> +
> + return 0;
> +}
> +#endif
> +
> +void build_info(void)
> +{
> + u32 sc_build = 0, sc_commit = 0;
> +
> + /* Get SCFW build and commit id */
> + sc_misc_build_info(-1, &sc_build, &sc_commit);
> + if (!sc_build) {
> + printf("SCFW does not support build info\n");
> + sc_commit = 0; /* Display 0 when the build info is not supported*/
> + }
> + printf("Build: SCFW %x\n", sc_commit); }
> +
> +int checkboard(void)
> +{
> + puts("Board: iMX8QM MEK\n");
> +
> + build_info();
> + print_bootinfo();
> +
> + return 0;
> +}
> +
> +int board_init(void)
> +{
> + /* Power up base board */
> + sc_pm_set_resource_power_mode(-1, SC_R_BOARD_R1,
> SC_PM_PW_MODE_ON);
> +
> + board_gpio_init();
> +
> + return 0;
> +}
> +
> +void detail_board_ddr_info(void)
> +{
> + puts("\nDDR ");
> +}
> +
> +/*
> + * Board specific reset that is system reset.
> + */
> +void reset_cpu(ulong addr)
> +{
> + /* TODO */
> +}
> +
> +#ifdef CONFIG_OF_BOARD_SETUP
> +int ft_board_setup(void *blob, bd_t *bd) {
> + return 0;
> +}
> +#endif
> +
> +int board_mmc_get_env_dev(int devno)
> +{
> + return devno;
> +}
> +
> +int board_late_init(void)
> +{
> +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> + env_set("board_name", "MEK");
> + env_set("board_rev", "iMX8QM");
> +#endif
> +
> + return 0;
> +}
> diff --git a/board/freescale/imx8qm_mek/imximage.cfg
> b/board/freescale/imx8qm_mek/imximage.cfg
> new file mode 100644
> index 0000000000..7dc6b93eb5
> --- /dev/null
> +++ b/board/freescale/imx8qm_mek/imximage.cfg
> @@ -0,0 +1,19 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Copyright 2018 NXP
> + */
> +
> +#define __ASSEMBLY__
> +
> +/* Boot from SD, sector size 0x400 */
> +BOOT_FROM SD 0x400
> +/* SoC type IMX8QM */
> +SOC_TYPE IMX8QM
> +/* Append seco container image */
> +APPEND mx8qm-ahab-container.img
> +/* Create the 2nd container */
> +CONTAINER
> +/* Add scfw image with exec attribute */ IMAGE SCU
> +mx8qm-mek-scfw-tcm.bin
> +/* Add ATF image with exec attribute */ IMAGE A35 spl/u-boot-spl.bin
> +0x00100000
> diff --git a/board/freescale/imx8qm_mek/spl.c
> b/board/freescale/imx8qm_mek/spl.c
> new file mode 100644
> index 0000000000..95ce9f37e8
> --- /dev/null
> +++ b/board/freescale/imx8qm_mek/spl.c
> @@ -0,0 +1,75 @@
> +/*
> + * Copyright 2018 NXP
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <dm.h>
> +#include <spl.h>
> +#include <dm/uclass.h>
> +#include <dm/device.h>
> +#include <dm/uclass-internal.h>
> +#include <dm/device-internal.h>
> +#include <dm/lists.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +void spl_board_init(void)
> +{
> + struct udevice *dev;
> + int offset;
> +
> + uclass_find_first_device(UCLASS_MISC, &dev);
> +
> + for (; dev; uclass_find_next_device(&dev)) {
> + if (device_probe(dev))
> + continue;
> + }
> +
> + offset = fdt_node_offset_by_compatible(gd->fdt_blob, -1,
> "nxp,imx8-pd");
> + while (offset != -FDT_ERR_NOTFOUND) {
> + lists_bind_fdt(gd->dm_root, offset_to_ofnode(offset),
> + NULL, true);
> + offset = fdt_node_offset_by_compatible(gd->fdt_blob, offset,
> + "nxp,imx8-pd");
> + }
> +
> + uclass_find_first_device(UCLASS_POWER_DOMAIN, &dev);
> +
> + for (; dev; uclass_find_next_device(&dev)) {
> + if (device_probe(dev))
> + continue;
> + }
> +
> + arch_cpu_init();
> +
> + board_early_init_f();
> +
> + timer_init();
> +
> + preloader_console_init();
> +
> + puts("Normal Boot\n");
> +}
> +
> +#ifdef CONFIG_SPL_LOAD_FIT
> +int board_fit_config_name_match(const char *name) {
> + /* Just empty function now - can't decide what to choose */
> + debug("%s: %s\n", __func__, name);
> +
> + return 0;
> +}
> +#endif
> +
> +void board_init_f(ulong dummy)
> +{
> + /* Clear global data */
> + memset((void *)gd, 0, sizeof(gd_t));
> +
> + /* Clear the BSS. */
> + memset(__bss_start, 0, __bss_end - __bss_start);
> +
> + board_init_r(NULL, 0);
> +}
> diff --git a/configs/imx8qm_mek_defconfig b/configs/imx8qm_mek_defconfig
> new file mode 100644 index 0000000000..238d44d1f5
> --- /dev/null
> +++ b/configs/imx8qm_mek_defconfig
> @@ -0,0 +1,75 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_IMX8=y
> +CONFIG_SYS_TEXT_BASE=0x80020000
> +CONFIG_SPL_GPIO_SUPPORT=y
> +CONFIG_SPL_LIBCOMMON_SUPPORT=y
> +CONFIG_SPL_LIBGENERIC_SUPPORT=y
> +CONFIG_SYS_MALLOC_F_LEN=0x2000
> +CONFIG_TARGET_IMX8QM_MEK=y
> +CONFIG_SPL_MMC_SUPPORT=y
> +CONFIG_SPL_SERIAL_SUPPORT=y
> +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
> +CONFIG_SPL=y
> +CONFIG_NR_DRAM_BANKS=3
> +CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
> +CONFIG_FIT=y
> +CONFIG_SPL_LOAD_FIT=y
> +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/imx8qm_m
> ek/imximage.cfg"
> +CONFIG_BOOTDELAY=3
> +CONFIG_LOG=y
> +CONFIG_SPL_BOARD_INIT=y
> +CONFIG_SPL_SEPARATE_BSS=y
> +CONFIG_SPL_POWER_SUPPORT=y
> +CONFIG_SPL_POWER_DOMAIN=y
> +CONFIG_SPL_WATCHDOG_SUPPORT=y
> +CONFIG_CMD_CPU=y
> +# CONFIG_CMD_IMPORTENV is not set
> +CONFIG_CMD_CLK=y
> +CONFIG_CMD_DM=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_DHCP=y
> +CONFIG_CMD_MII=y
> +CONFIG_CMD_PING=y
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_FAT=y
> +CONFIG_SPL_OF_CONTROL=y
> +CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8qm-mek"
> +CONFIG_ENV_IS_IN_MMC=y
> +CONFIG_SPL_DM=y
> +CONFIG_SPL_CLK=y
> +CONFIG_CLK_IMX8=y
> +CONFIG_CPU=y
> +CONFIG_DM_GPIO=y
> +CONFIG_MXC_GPIO=y
> +CONFIG_DM_PCA953X=y
> +CONFIG_DM_I2C=y
> +CONFIG_SYS_I2C_IMX_LPI2C=y
> +CONFIG_I2C_MUX=y
> +CONFIG_I2C_MUX_PCA954x=y
> +CONFIG_MISC=y
> +CONFIG_DM_MMC=y
> +CONFIG_PHYLIB=y
> +CONFIG_PHY_ADDR_ENABLE=y
> +CONFIG_PHY_ATHEROS=y
> +CONFIG_DM_ETH=y
> +CONFIG_PHY_GIGE=y
> +CONFIG_FEC_MXC_SHARE_MDIO=y
> +CONFIG_FEC_MXC_MDIO_BASE=0x5B040000
> +CONFIG_FEC_MXC=y
> +CONFIG_MII=y
> +CONFIG_PINCTRL=y
> +CONFIG_SPL_PINCTRL=y
> +CONFIG_PINCTRL_IMX8=y
> +CONFIG_POWER_DOMAIN=y
> +CONFIG_IMX8_POWER_DOMAIN=y
> +CONFIG_DM_REGULATOR=y
> +CONFIG_SPL_DM_REGULATOR=y
> +CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DM_REGULATOR_GPIO=y
> +CONFIG_SPL_DM_REGULATOR_GPIO=y
> +CONFIG_DM_SERIAL=y
> +CONFIG_FSL_LPUART=y
> +CONFIG_SPL_TINY_MEMSET=y
> +# CONFIG_EFI_LOADER is not set
> diff --git a/include/configs/imx8qm_mek.h b/include/configs/imx8qm_mek.h
> new file mode 100644 index 0000000000..02c5d1c054
> --- /dev/null
> +++ b/include/configs/imx8qm_mek.h
> @@ -0,0 +1,176 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Copyright 2018 NXP
> + */
> +
> +#ifndef __IMX8QM_MEK_H
> +#define __IMX8QM_MEK_H
> +
> +#include <linux/sizes.h>
> +#include <asm/arch/imx-regs.h>
> +
> +#ifdef CONFIG_SPL_BUILD
> +#define CONFIG_SPL_TEXT_BASE 0x0
> +#define CONFIG_SPL_MAX_SIZE (124 * 1024)
> +#define CONFIG_SYS_MONITOR_LEN (1024 * 1024)
> +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
> +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
> 0x800
> +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 0
> +
> +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
> +#define CONFIG_SPL_STACK 0x013E000
> +#define CONFIG_SPL_BSS_START_ADDR 0x00128000
> +#define CONFIG_SPL_BSS_MAX_SIZE 0x1000 /* 4 KB */
> +#define CONFIG_SYS_SPL_MALLOC_START 0x00120000
> +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x3000 /* 12 KB */
> +#define CONFIG_SERIAL_LPUART_BASE 0x5a060000
> +#define CONFIG_SYS_ICACHE_OFF
> +#define CONFIG_SYS_DCACHE_OFF
> +#define CONFIG_MALLOC_F_ADDR 0x00120000
> +
> +#define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE
> +
> +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
> +
> +#define CONFIG_OF_EMBED
> +#endif
> +
> +#define CONFIG_REMAKE_ELF
> +
> +#define CONFIG_BOARD_EARLY_INIT_F
> +
> +/* Flat Device Tree Definitions */
> +#define CONFIG_OF_BOARD_SETUP
> +
> +#undef CONFIG_CMD_EXPORTENV
> +#undef CONFIG_CMD_IMPORTENV
> +#undef CONFIG_CMD_IMLS
> +
> +#undef CONFIG_CMD_CRC32
> +#undef CONFIG_BOOTM_NETBSD
> +
> +#define CONFIG_FSL_ESDHC
> +#define CONFIG_FSL_USDHC
> +#define CONFIG_SYS_FSL_ESDHC_ADDR 0
> +#define USDHC1_BASE_ADDR 0x5B010000
> +#define USDHC2_BASE_ADDR 0x5B020000
> +#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
> +
> +#define CONFIG_ENV_OVERWRITE
> +
> +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> +
> +/* Initial environment variables */
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "script=boot.scr\0" \
> + "image=Image\0" \
> + "panel=NULL\0" \
> + "console=ttyLP0,${baudrate}
> earlycon=lpuart32,0x5a060000,${baudrate}\0" \
> + "fdt_addr=0x83000000\0" \
> + "fdt_high=0xffffffffffffffff\0" \
> + "boot_fdt=try\0" \
> + "fdt_file=fsl-imx8qxp-mek.dtb\0" \
> + "initrd_addr=0x83800000\0" \
> + "initrd_high=0xffffffffffffffff\0" \
> + "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
> + "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
> + "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
> + "mmcautodetect=yes\0" \
> + "mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
> + "loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr}
> ${script};\0" \
> + "bootscript=echo Running bootscript from mmc ...; " \
> + "source\0" \
> + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr}
> ${image}\0" \
> + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0"
> \
> + "mmcboot=echo Booting from mmc ...; " \
> + "run mmcargs; " \
> + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
> + "if run loadfdt; then " \
> + "booti ${loadaddr} - ${fdt_addr}; " \
> + "else " \
> + "echo WARN: Cannot load the DT; " \
> + "fi; " \
> + "else " \
> + "echo wait for boot; " \
> + "fi;\0" \
> + "netargs=setenv bootargs console=${console} " \
> + "root=/dev/nfs " \
> + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
> + "netboot=echo Booting from net ...; " \
> + "run netargs; " \
> + "if test ${ip_dyn} = yes; then " \
> + "setenv get_cmd dhcp; " \
> + "else " \
> + "setenv get_cmd tftp; " \
> + "fi; " \
> + "${get_cmd} ${loadaddr} ${image}; " \
> + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
> + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
> + "booti ${loadaddr} - ${fdt_addr}; " \
> + "else " \
> + "echo WARN: Cannot load the DT; " \
> + "fi; " \
> + "else " \
> + "booti; " \
> + "fi;\0"
> +
> +#define CONFIG_BOOTCOMMAND \
> + "mmc dev ${mmcdev}; if mmc rescan; then " \
> + "if run loadbootscript; then " \
> + "run bootscript; " \
> + "else " \
> + "if run loadimage; then " \
> + "run mmcboot; " \
> + "else run netboot; " \
> + "fi; " \
> + "fi; " \
> + "else booti ${loadaddr} - ${fdt_addr}; fi"
> +
> +/* Link Definitions */
> +#define CONFIG_LOADADDR 0x80280000
> +
> +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
> +
> +#define CONFIG_SYS_INIT_SP_ADDR 0x80200000
> +
> +/* Default environment is in SD */
> +#define CONFIG_ENV_SIZE 0x1000
> +#define CONFIG_ENV_OFFSET (64 * SZ_64K)
> +#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */
> +
> +#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
> +
> +/* On LPDDR4 board, USDHC1 is for eMMC, USDHC2 is for SD on CPU board
> */
> +#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */
> +#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2
> */
> +#define CONFIG_SYS_FSL_USDHC_NUM 2
> +
> +/* Size of malloc() pool */
> +#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (32 * 1024))
> * 1024)
> +
> +#define CONFIG_SYS_SDRAM_BASE 0x80000000
> +#define PHYS_SDRAM_1 0x80000000
> +#define PHYS_SDRAM_2 0x880000000
> +#define PHYS_SDRAM_1_SIZE 0x80000000 /* 2 GB */
> +#define PHYS_SDRAM_2_SIZE 0x100000000 /* 4 GB */
> +
> +/* Serial */
> +#define CONFIG_BAUDRATE 115200
> +
> +/* Monitor Command Prompt */
> +#define CONFIG_HUSH_PARSER
> +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
> +#define CONFIG_SYS_CBSIZE 2048
> +#define CONFIG_SYS_MAXARGS 64
> +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
> +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
> + sizeof(CONFIG_SYS_PROMPT) + 16)
> +
> +/* Generic Timer Definitions */
> +#define COUNTER_FREQUENCY 8000000 /* 8MHz */
> +
> +/* Networking */
> +#define CONFIG_FEC_XCV_TYPE RGMII
> +#define FEC_QUIRK_ENET_MAC
> +
> +#endif /* __IMX8QM_MEK_H */
> --
> 2.16.4
More information about the U-Boot
mailing list