[U-Boot] [PATCH 2/4] arm: dts: h6: Add Beelink GS1 initial support
Clément Péron
peron.clem at gmail.com
Thu Apr 11 22:53:57 UTC 2019
Hi,
On Mon, 8 Apr 2019 at 18:41, Clément Péron <peron.clem at gmail.com> wrote:
>
> Beelink GS1 is an Allwinner H6 based TV box,
> which support:
> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> - GPU Mali-T720
> - 2GB LPDDR3 RAM
> - 16GB eMMC
> - AXP805 PMIC
> - 1Gbps GMAC via RTL8211E
> - USB 2.0 and 3.0 Host
> - HDMI port
> - S/PDIF port
> - 5V/2A DC power supply
> - Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
>
> Signed-off-by: Clément Péron <peron.clem at gmail.com>
> ---
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/sun50i-h6-beelink-gs1.dts | 183 +++++++++++++++++++++++++
> configs/beelink_gs1_defconfig | 15 ++
> 3 files changed, 199 insertions(+)
> create mode 100644 arch/arm/dts/sun50i-h6-beelink-gs1.dts
> create mode 100644 configs/beelink_gs1_defconfig
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 0e2ffdb87f..4931b7d3cc 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -467,6 +467,7 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \
> sun50i-h5-orangepi-prime.dtb \
> sun50i-h5-orangepi-zero-plus2.dtb
> dtb-$(CONFIG_MACH_SUN50I_H6) += \
> + sun50i-h6-beelink-gs1.dtb \
> sun50i-h6-orangepi-lite2.dtb \
> sun50i-h6-orangepi-one-plus.dtb \
> sun50i-h6-pine-h64.dtb
> diff --git a/arch/arm/dts/sun50i-h6-beelink-gs1.dts b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
> new file mode 100644
> index 0000000000..c80862375f
> --- /dev/null
> +++ b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
> @@ -0,0 +1,183 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2019 Clément Péron <peron.clem at gmail.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h6.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "Beelink GS1";
> + compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + power {
> + label = "beelink:white:power";
> + gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> + default-state = "on";
> + };
> + };
> +
> + reg_vcc5v: vcc5v {
> + /* board wide 5V supply directly from the DC jack */
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-5v";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +};
> +
> +&mmc0 {
> + vmmc-supply = <®_cldo1>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&mmc2 {
> + vmmc-supply = <®_cldo1>;
> + vqmmc-supply = <®_bldo2>;
> + non-removable;
> + cap-mmc-hw-reset;
bus-width = <8>;
I missed the bus-width.
The is the same issue on Pine H64
Clement
> + status = "okay";
> +};
> +
> +&r_i2c {
> + status = "okay";
> +
> + axp805: pmic at 36 {
> + compatible = "x-powers,axp805", "x-powers,axp806";
> + reg = <0x36>;
> + interrupt-parent = <&r_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + x-powers,self-working-mode;
> + vina-supply = <®_vcc5v>;
> + vinb-supply = <®_vcc5v>;
> + vinc-supply = <®_vcc5v>;
> + vind-supply = <®_vcc5v>;
> + vine-supply = <®_vcc5v>;
> + aldoin-supply = <®_vcc5v>;
> + bldoin-supply = <®_vcc5v>;
> + cldoin-supply = <®_vcc5v>;
> +
> + regulators {
> + reg_aldo1: aldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-pl";
> + };
> +
> + reg_aldo2: aldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-ac200";
> + regulator-enable-ramp-delay = <100000>;
> + };
> +
> + reg_aldo3: aldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc25-dram";
> + };
> +
> + reg_bldo1: bldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-bias-pll";
> + };
> +
> + reg_bldo2: bldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-efuse-pcie-hdmi-io";
> + };
> +
> + reg_bldo3: bldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-dcxoio";
> + };
> +
> + bldo4 {
> + /* unused */
> + };
> +
> + reg_cldo1: cldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-3v3";
> + };
> +
> + reg_cldo2: cldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-1";
> + };
> +
> + reg_cldo3: cldo3 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-2";
> + };
> +
> + reg_dcdca: dcdca {
> + regulator-always-on;
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-cpu";
> + };
> +
> + reg_dcdcc: dcdcc {
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-gpu";
> + };
> +
> + reg_dcdcd: dcdcd {
> + regulator-always-on;
> + regulator-min-microvolt = <960000>;
> + regulator-max-microvolt = <960000>;
> + regulator-name = "vdd-sys";
> + };
> +
> + reg_dcdce: dcdce {
> + regulator-always-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vcc-dram";
> + };
> +
> + sw {
> + /* unused */
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_ph_pins>;
> + status = "okay";
> +};
> diff --git a/configs/beelink_gs1_defconfig b/configs/beelink_gs1_defconfig
> new file mode 100644
> index 0000000000..ef4dd29549
> --- /dev/null
> +++ b/configs/beelink_gs1_defconfig
> @@ -0,0 +1,15 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_SUNXI=y
> +CONFIG_SPL=y
> +CONFIG_MACH_SUN50I_H6=y
> +CONFIG_MMC0_CD_PIN="PF6"
> +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> +# CONFIG_PSCI_RESET is not set
> +CONFIG_NR_DRAM_BANKS=1
> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> +# CONFIG_CMD_FLASH is not set
> +# CONFIG_SPL_DOS_PARTITION is not set
> +# CONFIG_SPL_EFI_PARTITION is not set
> +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-beelink-gs1"
> +CONFIG_LED=y
> +CONFIG_LED_GPIO=y
> --
> 2.17.1
>
More information about the U-Boot
mailing list