[U-Boot] [PATCH v2 2/3] arm: dts: h6: Add Beelink GS1 initial support
Clément Péron
peron.clem at gmail.com
Sun Apr 14 21:27:20 UTC 2019
Hi,
On Sun, 14 Apr 2019 at 19:29, Jagan Teki <jagan at amarulasolutions.com> wrote:
>
> On Fri, Apr 12, 2019 at 7:45 PM Clément Péron <peron.clem at gmail.com> wrote:
> >
> > Beelink GS1 is an Allwinner H6 based TV box,
> > which support:
> > - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> > - GPU Mali-T720
> > - 2GB LPDDR3 RAM
> > - 16GB eMMC
> > - AXP805 PMIC
> > - 1Gbps GMAC via RTL8211E
> > - USB 2.0 and 3.0 Host
> > - HDMI port
> > - S/PDIF port
> > - 5V/2A DC power supply
> > - Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
>
> Please dts sync commit details here.
>
> >
> > Signed-off-by: Clément Péron <peron.clem at gmail.com>
> > ---
> > arch/arm/dts/Makefile | 1 +
> > arch/arm/dts/sun50i-h6-beelink-gs1.dts | 184 +++++++++++++++++++++++++
>
> Seems like this has part of required nodes, sync the complete dts.
Ok so you want to add the complete dts from linux.
I think only IP used in U-boot are needed.
I will do that in v3
>
> > configs/beelink_gs1_defconfig | 15 ++
>
> Add entry on board/sunxi/MAINTAINERS
Ok
>
> > 3 files changed, 200 insertions(+)
> > create mode 100644 arch/arm/dts/sun50i-h6-beelink-gs1.dts
> > create mode 100644 configs/beelink_gs1_defconfig
> >
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> > index 86a01c2c70..61e7156284 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -467,6 +467,7 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \
> > sun50i-h5-orangepi-prime.dtb \
> > sun50i-h5-orangepi-zero-plus2.dtb
> > dtb-$(CONFIG_MACH_SUN50I_H6) += \
> > + sun50i-h6-beelink-gs1.dtb \
> > sun50i-h6-orangepi-lite2.dtb \
> > sun50i-h6-orangepi-one-plus.dtb \
> > sun50i-h6-pine-h64.dtb
> > diff --git a/arch/arm/dts/sun50i-h6-beelink-gs1.dts b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
> > new file mode 100644
> > index 0000000000..54b0882bed
> > --- /dev/null
> > +++ b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
> > @@ -0,0 +1,184 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> > +/*
> > + * Copyright (C) 2019 Clément Péron <peron.clem at gmail.com>
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "sun50i-h6.dtsi"
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +
> > +/ {
> > + model = "Beelink GS1";
> > + compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
> > +
> > + aliases {
> > + serial0 = &uart0;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > +
> > + power {
> > + label = "beelink:white:power";
> > + gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> > + default-state = "on";
> > + };
> > + };
> > +
> > + reg_vcc5v: vcc5v {
> > + /* board wide 5V supply directly from the DC jack */
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc-5v";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-always-on;
> > + };
> > +};
> > +
> > +&mmc0 {
> > + vmmc-supply = <®_cldo1>;
> > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> > + bus-width = <4>;
> > + status = "okay";
> > +};
> > +
> > +&mmc2 {
> > + vmmc-supply = <®_cldo1>;
> > + vqmmc-supply = <®_bldo2>;
> > + non-removable;
> > + cap-mmc-hw-reset;
> > + bus-width = <8>;
> > + status = "okay";
> > +};
> > +
> > +&r_i2c {
> > + status = "okay";
> > +
> > + axp805: pmic at 36 {
> > + compatible = "x-powers,axp805", "x-powers,axp806";
> > + reg = <0x36>;
> > + interrupt-parent = <&r_intc>;
> > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> > + interrupt-controller;
> > + #interrupt-cells = <1>;
> > + x-powers,self-working-mode;
> > + vina-supply = <®_vcc5v>;
> > + vinb-supply = <®_vcc5v>;
> > + vinc-supply = <®_vcc5v>;
> > + vind-supply = <®_vcc5v>;
> > + vine-supply = <®_vcc5v>;
> > + aldoin-supply = <®_vcc5v>;
> > + bldoin-supply = <®_vcc5v>;
> > + cldoin-supply = <®_vcc5v>;
> > +
> > + regulators {
> > + reg_aldo1: aldo1 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-pl";
> > + };
> > +
> > + reg_aldo2: aldo2 {
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-ac200";
> > + regulator-enable-ramp-delay = <100000>;
> > + };
> > +
> > + reg_aldo3: aldo3 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc25-dram";
> > + };
> > +
> > + reg_bldo1: bldo1 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-name = "vcc-bias-pll";
> > + };
> > +
> > + reg_bldo2: bldo2 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-name = "vcc-efuse-pcie-hdmi-io";
> > + };
> > +
> > + reg_bldo3: bldo3 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-name = "vcc-dcxoio";
> > + };
> > +
> > + bldo4 {
> > + /* unused */
> > + };
> > +
> > + reg_cldo1: cldo1 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-3v3";
> > + };
> > +
> > + reg_cldo2: cldo2 {
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-wifi-1";
> > + };
> > +
> > + reg_cldo3: cldo3 {
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-wifi-2";
> > + };
> > +
> > + reg_dcdca: dcdca {
> > + regulator-always-on;
> > + regulator-min-microvolt = <810000>;
> > + regulator-max-microvolt = <1080000>;
> > + regulator-name = "vdd-cpu";
> > + };
> > +
> > + reg_dcdcc: dcdcc {
> > + regulator-min-microvolt = <810000>;
> > + regulator-max-microvolt = <1080000>;
> > + regulator-name = "vdd-gpu";
> > + };
> > +
> > + reg_dcdcd: dcdcd {
> > + regulator-always-on;
> > + regulator-min-microvolt = <960000>;
> > + regulator-max-microvolt = <960000>;
> > + regulator-name = "vdd-sys";
> > + };
> > +
> > + reg_dcdce: dcdce {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1200000>;
> > + regulator-name = "vcc-dram";
> > + };
> > +
> > + sw {
> > + /* unused */
> > + };
> > + };
> > + };
> > +};
> > +
> > +&uart0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart0_ph_pins>;
> > + status = "okay";
> > +};
> > diff --git a/configs/beelink_gs1_defconfig b/configs/beelink_gs1_defconfig
> > new file mode 100644
> > index 0000000000..ef4dd29549
> > --- /dev/null
> > +++ b/configs/beelink_gs1_defconfig
> > @@ -0,0 +1,15 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_SUNXI=y
> > +CONFIG_SPL=y
> > +CONFIG_MACH_SUN50I_H6=y
> > +CONFIG_MMC0_CD_PIN="PF6"
> > +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> > +# CONFIG_PSCI_RESET is not set
> > +CONFIG_NR_DRAM_BANKS=1
> > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > +# CONFIG_CMD_FLASH is not set
> > +# CONFIG_SPL_DOS_PARTITION is not set
> > +# CONFIG_SPL_EFI_PARTITION is not set
> > +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-beelink-gs1"
> > +CONFIG_LED=y
> > +CONFIG_LED_GPIO=y
>
> Seems like most of Allwinner gpio's are gpio-leds. so select LED
> (since it's dm led core) in arch/arm/Kconfig if LED_GPIO. I'm thinking
> this could be proper assignment.
We can't do that as LED_GPIO depends on LED.
More information about the U-Boot
mailing list