[U-Boot] [PATCH v2 5/5] board: toradex: add colibri imx8qxp 2gb wb it v1.0b module support
Stefano Babic
sbabic at denx.de
Fri Apr 26 09:46:20 UTC 2019
On 26/04/19 11:20, Marcel Ziswiler wrote:
> Hi Igor
>
> Sorry, somehow I missed your comments below (;-p).
>
> I will send out a v4 (yes there already was a v3 BTW) shortly including
> the SPL resp. without SPL build fix.
Fine - the series (without 5/5) is already applied on u-boot-imx. Please
just send 5/5.
Regards,
Stefano
>
> On Thu, 2019-04-11 at 12:47 +0200, Igor Opaniuk wrote:
>> Hi Marcel,
>>
>> Reviewed-by: Igor Opaniuk <igor.opaniuk at toradex.com>
>>
>> Some minor comments below (can be addressed in different patch):
>>
>> On Tue, Apr 9, 2019 at 5:34 PM Marcel Ziswiler <marcel at ziswiler.com>
>> wrote:
>>> From: Marcel Ziswiler <marcel.ziswiler at toradex.com>
>>>
>>> This commit adds initial support for the Toradex Colibri iMX8QXP
>>> 2GB WB
>>> IT V1.0B module. Unlike the V1.0A early access samples exclusively
>>> booting from SD card, they are now strapped to boot from eFuses
>>> which
>>> are factory fused to properly boot from their on-module eMMC. U-
>>> Boot
>>> supports either booting from the on-module eMMC or may be used for
>>> recovery purpose using the universal update utility (uuu) aka
>>> mfgtools
>>> 3.0.
>>>
>>> Functionality wise the following is known to be working:
>>> - eMMC and MMC/SD card
>>> - Ethernet
>>> - GPIOs
>>> - I2C
>>>
>>> Unfortunately, there is no USB functionality for the i.MX 8QXP as
>>> of
>>> yet.
>>>
>>> Signed-off-by: Marcel Ziswiler <marcel.ziswiler at toradex.com>
>>>
>>> ---
>>>
>>> Changes in v2:
>>> - Changed imx-atf git clone command to include initial branch
>>> information as suggested by Igor.
>>> - Sorted board file includes alphabetically as suggested by Igor.
>>> - Got rid of SPL configuration in legacy header file as suggested
>>> by
>>> Igor and the whole use of SPL on i.MX 8X anyway neither works
>>> well
>>> nor makes any much sense at all.
>>>
>>> arch/arm/dts/Makefile | 4 +-
>>> arch/arm/dts/fsl-imx8qxp-colibri-u-boot.dtsi | 112 ++++++
>>> arch/arm/dts/fsl-imx8qxp-colibri.dts | 328
>>> ++++++++++++++++++
>>> arch/arm/mach-imx/imx8/Kconfig | 6 +
>>> board/toradex/colibri-imx8qxp/Kconfig | 30 ++
>>> board/toradex/colibri-imx8qxp/MAINTAINERS | 9 +
>>> board/toradex/colibri-imx8qxp/Makefile | 7 +
>>> board/toradex/colibri-imx8qxp/README | 66 ++++
>>> .../toradex/colibri-imx8qxp/colibri-imx8qxp.c | 212 +++++++++++
>>> board/toradex/colibri-imx8qxp/imximage.cfg | 24 ++
>>> configs/colibri-imx8qxp_defconfig | 53 +++
>>> include/configs/colibri-imx8qxp.h | 214 ++++++++++++
>>> 12 files changed, 1064 insertions(+), 1 deletion(-)
>>> create mode 100644 arch/arm/dts/fsl-imx8qxp-colibri-u-boot.dtsi
>>> create mode 100644 arch/arm/dts/fsl-imx8qxp-colibri.dts
>>> create mode 100644 board/toradex/colibri-imx8qxp/Kconfig
>>> create mode 100644 board/toradex/colibri-imx8qxp/MAINTAINERS
>>> create mode 100644 board/toradex/colibri-imx8qxp/Makefile
>>> create mode 100644 board/toradex/colibri-imx8qxp/README
>>> create mode 100644 board/toradex/colibri-imx8qxp/colibri-imx8qxp.c
>>> create mode 100644 board/toradex/colibri-imx8qxp/imximage.cfg
>>> create mode 100644 configs/colibri-imx8qxp_defconfig
>>> create mode 100644 include/configs/colibri-imx8qxp.h
>>>
>>> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
>>> index 13d1d67624..2a551d42a4 100644
>>> --- a/arch/arm/dts/Makefile
>>> +++ b/arch/arm/dts/Makefile
>>> @@ -559,7 +559,9 @@ dtb-$(CONFIG_MX7) += imx7d-sdb.dtb \
>>>
>>> dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-evk.dtb
>>>
>>> -dtb-$(CONFIG_ARCH_IMX8) += fsl-imx8qxp-mek.dtb
>>> +dtb-$(CONFIG_ARCH_IMX8) += \
>>> + fsl-imx8qxp-colibri.dtb \
>>> + fsl-imx8qxp-mek.dtb
>>>
>>> dtb-$(CONFIG_ARCH_IMX8M) += fsl-imx8mq-evk.dtb
>>>
>>> diff --git a/arch/arm/dts/fsl-imx8qxp-colibri-u-boot.dtsi
>>> b/arch/arm/dts/fsl-imx8qxp-colibri-u-boot.dtsi
>>> new file mode 100644
>>> index 0000000000..f8686befdf
>>> --- /dev/null
>>> +++ b/arch/arm/dts/fsl-imx8qxp-colibri-u-boot.dtsi
>>> @@ -0,0 +1,112 @@
>>> +// SPDX-License-Identifier: GPL-2.0+ OR X11
>>> +/*
>>> + * Copyright 2019 Toradex AG
>>> + */
>>> +
>>> +&mu {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&clk {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&iomuxc {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&pd_lsio {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&pd_lsio_gpio0 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&pd_lsio_gpio1 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&pd_lsio_gpio2 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&pd_lsio_gpio3 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&pd_lsio_gpio4 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&pd_lsio_gpio5 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&pd_lsio_gpio6 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&pd_lsio_gpio7 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&pd_conn {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&pd_conn_sdch0 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&pd_conn_sdch1 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&pd_conn_sdch2 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&gpio0 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&gpio1 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&gpio2 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&gpio3 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&gpio4 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&gpio5 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&gpio6 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&gpio7 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&lpuart3 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&usdhc1 {
>>> + u-boot,dm-spl;
>>> +};
>>> +
>>> +&usdhc2 {
>>> + u-boot,dm-spl;
>>> +};
>>> diff --git a/arch/arm/dts/fsl-imx8qxp-colibri.dts
>>> b/arch/arm/dts/fsl-imx8qxp-colibri.dts
>>> new file mode 100644
>>> index 0000000000..0c20edf2cf
>>> --- /dev/null
>>> +++ b/arch/arm/dts/fsl-imx8qxp-colibri.dts
>>> @@ -0,0 +1,328 @@
>>> +// SPDX-License-Identifier: GPL-2.0+ OR X11
>>> +/*
>>> + * Copyright 2019 Toradex AG
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "fsl-imx8qxp.dtsi"
>>> +#include "fsl-imx8qxp-colibri-u-boot.dtsi"
>>> +
>>> +/ {
>>> + model = "Toradex Colibri iMX8QXP";
>>> + compatible = "toradex,colibri-imx8qxp", "fsl,imx8qxp";
>>> +
>>> + chosen {
>>> + bootargs = "console=ttyLP3,115200
>>> earlycon=lpuart32,0x5a090000,115200";
>>> + stdout-path = &lpuart3;
>>> + };
>>> +
>>> + reg_usbh_vbus: regulator-usbh-vbus {
>>> + compatible = "regulator-fixed";
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pinctrl_usbh1_reg>;
>>> + regulator-name = "usbh_vbus";
>>> + regulator-min-microvolt = <5000000>;
>>> + regulator-max-microvolt = <5000000>;
>>> + gpio = <&gpio4 3 GPIO_ACTIVE_LOW>;
>>> + };
>>> +};
>>> +
>>> +&iomuxc {
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pinctrl_hog0>, <&pinctrl_hog1>,
>>> <&pinctrl_hog2>;
>>> +
>>> + colibri-imx8qxp {
>>> + pinctrl_lpuart0: lpuart0grp {
>>> + fsl,pins = <
>>> + SC_P_UART0_RX_ADMA_UART0_RX 0x0
>>> 6000020
>>> + SC_P_UART0_TX_ADMA_UART0_TX 0x0
>>> 6000020
>>> + >;
>>> + };
>>> +
>>> + pinctrl_lpuart3: lpuart3grp {
>>> + fsl,pins = <
>>> + SC_P_FLEXCAN2_RX_ADMA_UART3_RX 0x0
>>> 6000020
>>> + SC_P_FLEXCAN2_TX_ADMA_UART3_TX 0x0
>>> 6000020
>>> + >;
>>> + };
>>> +
>>> + pinctrl_lpuart3_ctrl: lpuart3ctrlgrp {
>>> + fsl,pins = <
>>> + SC_P_MIPI_DSI1_GPIO0_01_LSIO_GPIO2_
>>> IO00 0x00000020 /* DTR */
>>> + SC_P_SAI1_RXD_LSIO_GPIO0_IO29
>>> 0x00000020 /* CTS */
>>> + SC_P_SAI1_RXC_LSIO_GPIO0_IO30
>>> 0x00000020 /* RTS */
>>> + SC_P_CSI_RESET_LSIO_GPIO3_IO03
>>> 0x00000020 /* DSR */
>>> + SC_P_USDHC1_CD_B_LSIO_GPIO4_IO22
>>> 0x00000020 /* DCD */
>>> + SC_P_CSI_EN_LSIO_GPIO3_IO02
>>> 0x00000020 /* RI */
>>> + >;
>>> + };
>>> +
>>> + pinctrl_fec1: fec1grp {
>>> + fsl,pins = <
>>> + SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENE
>>> TB0_PAD 0x000014a0 /* Use pads in 3.3V mode */
>>> + SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENE
>>> TB1_PAD 0x000014a0 /* Use pads in 3.3V mode */
>>> + SC_P_ENET0_MDC_CONN_ENET0_MDC
>>> 0x06000020
>>> + SC_P_ENET0_MDIO_CONN_ENET0_MDIO
>>> 0x06000020
>>> + SC_P_ENET0_RGMII_TX_CTL_CONN_ENET0_
>>> RGMII_TX_CTL 0x00000061
>>> + SC_P_ENET0_RGMII_TXC_CONN_ENET0_RCL
>>> K50M_OUT 0x06000061
>>> + SC_P_ENET0_RGMII_TXD0_CONN_ENET0_RG
>>> MII_TXD0 0x00000061
>>> + SC_P_ENET0_RGMII_TXD1_CONN_ENET0_RG
>>> MII_TXD1 0x00000061
>>> + SC_P_ENET0_RGMII_RX_CTL_CONN_ENET0_
>>> RGMII_RX_CTL 0x00000061
>>> + SC_P_ENET0_RGMII_RXD0_CONN_ENET0_RG
>>> MII_RXD0 0x00000061
>>> + SC_P_ENET0_RGMII_RXD1_CONN_ENET0_RG
>>> MII_RXD1 0x00000061
>>> + SC_P_ENET0_RGMII_RXD2_CONN_ENET0_RM
>>> II_RX_ER 0x00000061
>>> + >;
>>> + };
>>> +
>>> + pinctrl_gpio_bl_on: gpio-bl-on {
>>> + fsl,pins = <
>>> + SC_P_QSPI0A_DATA3_LSIO_GPIO3_IO12
>>> 0x00000040
>>> + >;
>>> + };
>>> +
>>> + pinctrl_hog0: hog0grp {
>>> + fsl,pins = <
>>> + SC_P_COMP_CTL_GPIO_1V8_3V3_GPIORHB_
>>> PAD 0x000514a0 /* Use pads in 3.3V mode */
>>> + >;
>>> + };
>>> +
>>> + pinctrl_hog1: hog1grp {
>>> + fsl,pins = <
>>> + SC_P_QSPI0A_DATA1_LSIO_GPIO3_IO10
>>> 0x00000020 /* 45 */
>>> + SC_P_ENET0_RGMII_TXD3_LSIO_GPIO5_IO
>>> 02 0x06000020 /* 65 */
>>> + SC_P_CSI_D07_CI_PI_D09
>>> 0x00000061
>>> + SC_P_QSPI0A_DATA2_LSIO_GPIO3_IO11
>>> 0x00000020 /* 69 */
>>> + SC_P_QSPI0A_DQS_LSIO_GPIO3_IO13
>>> 0x00000020 /* 73 */
>>> + SC_P_SAI0_TXC_LSIO_GPIO0_IO26
>>> 0x00000020 /* 79 */
>>> + SC_P_CSI_D02_CI_PI_D04
>>> 0x00000061
>>> + SC_P_ENET0_RGMII_RXC_LSIO_GPIO5_IO0
>>> 3 0x06000020 /* 85 */
>>> + SC_P_CSI_D06_CI_PI_D08
>>> 0x00000061
>>> + SC_P_QSPI0B_SCLK_LSIO_GPIO3_IO17
>>> 0x00000020 /* 95 */
>>> + SC_P_SAI0_RXD_LSIO_GPIO0_IO27
>>> 0x00000020 /* 97 */
>>> + SC_P_CSI_D03_CI_PI_D05
>>> 0x00000061
>>> + SC_P_QSPI0B_DATA0_LSIO_GPIO3_IO18
>>> 0x00000020 /* 99 */
>>> + SC_P_SAI0_TXFS_LSIO_GPIO0_IO28
>>> 0x00000020 /* 101 */
>>> + SC_P_CSI_D00_CI_PI_D02
>>> 0x00000061
>>> + SC_P_SAI0_TXD_LSIO_GPIO0_IO25
>>> 0x00000020 /* 103 */
>>> + SC_P_CSI_D01_CI_PI_D03
>>> 0x00000061
>>
>> I seems that in 20 lines above alignment is broken a bit.
>
> No, I believe Max intentionally did it that way downstream indicating
> that those SODIMM pins are each multiplexed onto two SoC balls. Toradex
> does this at times to gain greater pin compatibility across our module
> families.
>
> Further comments down below taken into account. Thanks!
>
> Cheers
>
> Marcel
>
>>> + SC_P_QSPI0B_DATA1_LSIO_GPIO3_IO19
>>> 0x00000020 /* 105 */
>>> + SC_P_QSPI0B_DATA2_LSIO_GPIO3_IO20
>>> 0x00000020 /* 107 */
>>> + SC_P_USB_SS3_TC2_LSIO_GPIO4_IO05
>>> 0x00000020 /* 127 */
>>> + SC_P_USB_SS3_TC3_LSIO_GPIO4_IO06
>>> 0x00000020 /* 131 */
>>> + SC_P_USB_SS3_TC1_LSIO_GPIO4_IO04
>>> 0x00000020 /* 133 */
>>> + SC_P_CSI_PCLK_LSIO_GPIO3_IO00
>>> 0x00000020 /* 96 */
>>> + SC_P_QSPI0B_DATA3_LSIO_GPIO3_IO21
>>> 0x00000020 /* 98 */
>>> + SC_P_SAI1_RXFS_LSIO_GPIO0_IO31
>>> 0x00000020 /* 100 */
>>> + SC_P_QSPI0B_DQS_LSIO_GPIO3_IO22
>>> 0x00000020 /* 102 */
>>> + SC_P_QSPI0B_SS0_B_LSIO_GPIO3_IO23
>>> 0x00000020 /* 104 */
>>> + SC_P_QSPI0B_SS1_B_LSIO_GPIO3_IO24
>>> 0x00000020 /* 106 */
>>> + >;
>>> + };
>>> +
>>> + pinctrl_hog2: hog2grp {
>>> + fsl,pins = <
>>> + SC_P_CSI_MCLK_LSIO_GPIO3_IO01
>>> 0x00000020 /* 75 */
>>> + SC_P_QSPI0A_SS0_B_LSIO_GPIO3_IO14
>>> 0x00000020 /* 77 */
>>> + SC_P_QSPI0A_SS1_B_LSIO_GPIO3_IO15
>>> 0x00000020 /* 89 */
>>> + SC_P_QSPI0A_SCLK_LSIO_GPIO3_IO16
>>> 0x00000020 /* 93 */
>>> + >;
>>> + };
>>> +
>>> + /* Off Module I2C */
>>> + pinctrl_i2c1: i2c1grp {
>>> + fsl,pins = <
>>> + SC_P_MIPI_DSI0_GPIO0_00_ADMA_I2C1_S
>>> CL 0x06000021
>>> + SC_P_MIPI_DSI0_GPIO0_01_ADMA_I2C1_S
>>> DA 0x06000021
>>> + >;
>>> + };
>>> +
>>> + /*INT*/
>>> + pinctrl_usb3503a: usb3503a-grp {
>>> + fsl,pins = <
>>> + SC_P_MIPI_CSI0_MCLK_OUT_LSIO_GPIO3_
>>> IO04 0x00000061
>>> + >;
>>> + };
>>> +
>>> + pinctrl_usbc_det: usbc-det {
>>> + fsl,pins = <
>>> + SC_P_ENET0_REFCLK_125M_25M_LSIO_GPI
>>> O5_IO09 0x06000040
>>> + >;
>>> + };
>>> +
>>> + pinctrl_usbh1_reg: usbh1-reg {
>>> + fsl,pins = <
>>> + SC_P_USB_SS3_TC0_LSIO_GPIO4_IO03
>>> 0x06000040
>>> + >;
>>> + };
>>> +
>>> + pinctrl_usdhc1: usdhc1grp {
>>> + fsl,pins = <
>>> + SC_P_EMMC0_CLK_CONN_EMMC0_CLK
>>> 0x06000041
>>> + SC_P_EMMC0_CMD_CONN_EMMC0_CMD
>>> 0x00000021
>>> + SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0
>>> 0x00000021
>>> + SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1
>>> 0x00000021
>>> + SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2
>>> 0x00000021
>>> + SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3
>>> 0x00000021
>>> + SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4
>>> 0x00000021
>>> + SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5
>>> 0x00000021
>>> + SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6
>>> 0x00000021
>>> + SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7
>>> 0x00000021
>>> + SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE
>>> 0x00000041
>>> + SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET
>>> _B 0x00000021
>>> + >;
>>> + };
>>> +
>>> + pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
>>> + fsl,pins = <
>>> + SC_P_EMMC0_CLK_CONN_EMMC0_CLK
>>> 0x06000041
>>> + SC_P_EMMC0_CMD_CONN_EMMC0_CMD
>>> 0x00000021
>>> + SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0
>>> 0x00000021
>>> + SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1
>>> 0x00000021
>>> + SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2
>>> 0x00000021
>>> + SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3
>>> 0x00000021
>>> + SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4
>>> 0x00000021
>>> + SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5
>>> 0x00000021
>>> + SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6
>>> 0x00000021
>>> + SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7
>>> 0x00000021
>>> + SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE
>>> 0x00000041
>>> + SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET
>>> _B 0x00000021
>>> + >;
>>> + };
>>> +
>>> + pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
>>> + fsl,pins = <
>>> + SC_P_EMMC0_CLK_CONN_EMMC0_CLK
>>> 0x06000041
>>> + SC_P_EMMC0_CMD_CONN_EMMC0_CMD
>>> 0x00000021
>>> + SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0
>>> 0x00000021
>>> + SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1
>>> 0x00000021
>>> + SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2
>>> 0x00000021
>>> + SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3
>>> 0x00000021
>>> + SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4
>>> 0x00000021
>>> + SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5
>>> 0x00000021
>>> + SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6
>>> 0x00000021
>>> + SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7
>>> 0x00000021
>>> + SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE
>>> 0x00000041
>>> + SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET
>>> _B 0x00000021
>>> + >;
>>> + };
>>> +
>>> + pinctrl_usdhc2_gpio: usdhc2gpiogrp {
>>> + fsl,pins = <
>>> + SC_P_QSPI0A_DATA0_LSIO_GPIO3_IO09
>>> 0x06000021
>>> + >;
>>> + };
>>> +
>>> + pinctrl_usdhc2: usdhc2grp {
>>> + fsl,pins = <
>>> + SC_P_USDHC1_CLK_CONN_USDHC1_CLK
>>> 0x06000041
>>> + SC_P_USDHC1_CMD_CONN_USDHC1_CMD
>>> 0x00000021
>>> + SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0
>>> 0x00000021
>>> + SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1
>>> 0x00000021
>>> + SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2
>>> 0x00000021
>>> + SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3
>>> 0x00000021
>>> + SC_P_USDHC1_VSELECT_CONN_USDHC1_VSE
>>> LECT 0x00000021
>>> + >;
>>> + };
>>> +
>>> + pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
>>> + fsl,pins = <
>>> + SC_P_USDHC1_CLK_CONN_USDHC1_CLK
>>> 0x06000041
>>> + SC_P_USDHC1_CMD_CONN_USDHC1_CMD
>>> 0x00000021
>>> + SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0
>>> 0x00000021
>>> + SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1
>>> 0x00000021
>>> + SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2
>>> 0x00000021
>>> + SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3
>>> 0x00000021
>>> + SC_P_USDHC1_VSELECT_CONN_USDHC1_VSE
>>> LECT 0x00000021
>>> + >;
>>> + };
>>> +
>>> + pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
>>> + fsl,pins = <
>>> + SC_P_USDHC1_CLK_CONN_USDHC1_CLK
>>> 0x06000041
>>> + SC_P_USDHC1_CMD_CONN_USDHC1_CMD
>>> 0x00000021
>>> + SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0
>>> 0x00000021
>>> + SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1
>>> 0x00000021
>>> + SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2
>>> 0x00000021
>>> + SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3
>>> 0x00000021
>>> + SC_P_USDHC1_VSELECT_CONN_USDHC1_VSE
>>> LECT 0x00000021
>>> + >;
>>> + };
>>> + };
>>> +};
>>> +
>>> +&lpuart0 {
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pinctrl_lpuart0>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&lpuart3 {
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pinctrl_lpuart3>, <&pinctrl_lpuart3_ctrl>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&gpio0 {
>>> + status = "okay";
>>> +};
>>> +
>>> +&gpio1 {
>>> + status = "okay";
>>> +};
>>> +
>>> +&gpio3 {
>>> + status = "okay";
>>> +};
>>> +
>>> +&gpio4 {
>>> + status = "okay";
>>> +};
>>> +
>>> +&fec1 {
>>> + phy-handle = <ðphy0>;
>>> + phy-mode = "rmii";
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pinctrl_fec1>;
>>> + status = "okay";
>>> +
>>> + mdio {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + ethphy0: ethernet-phy at 2 {
>>> + compatible = "ethernet-phy-ieee802.3-c22";
>>> + max-speed = <100>;
>>> + reg = <2>;
>>> + };
>>> + };
>>> +};
>>> +
>>> +&i2c1 {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + clock-frequency = <100000>;
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pinctrl_i2c1>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&usdhc1 {
>>> + bus-width = <8>;
>>> + non-removable;
>>> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
>>> + pinctrl-0 = <&pinctrl_usdhc1>;
>>> + pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
>>> + pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&usdhc2 {
>>> + bus-width = <4>;
>>> + cd-gpios = <&gpio3 9 GPIO_ACTIVE_LOW>;
>>> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
>>> + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
>>> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>,
>>> <&pinctrl_usdhc2_gpio>;
>>> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>,
>>> <&pinctrl_usdhc2_gpio>;
>>> + status = "okay";
>>> +};
>>> diff --git a/arch/arm/mach-imx/imx8/Kconfig b/arch/arm/mach-
>>> imx/imx8/Kconfig
>>> index f76a139684..feea07f135 100644
>>> --- a/arch/arm/mach-imx/imx8/Kconfig
>>> +++ b/arch/arm/mach-imx/imx8/Kconfig
>>> @@ -22,6 +22,11 @@ choice
>>> prompt "i.MX8 board select"
>>> optional
>>>
>>> +config TARGET_COLIBRI_IMX8QXP
>>> + bool "Support Colibri iMX8QXP module"
>>> + select BOARD_LATE_INIT
>>> + select IMX8QXP
>>> +
>>> config TARGET_IMX8QXP_MEK
>>> bool "Support i.MX8QXP MEK board"
>>> select BOARD_LATE_INIT
>>> @@ -30,5 +35,6 @@ config TARGET_IMX8QXP_MEK
>>> endchoice
>>>
>>> source "board/freescale/imx8qxp_mek/Kconfig"
>>> +source "board/toradex/colibri-imx8qxp/Kconfig"
>>>
>>> endif
>>> diff --git a/board/toradex/colibri-imx8qxp/Kconfig
>>> b/board/toradex/colibri-imx8qxp/Kconfig
>>> new file mode 100644
>>> index 0000000000..340fe72816
>>> --- /dev/null
>>> +++ b/board/toradex/colibri-imx8qxp/Kconfig
>>> @@ -0,0 +1,30 @@
>>> +if TARGET_COLIBRI_IMX8QXP
>>> +
>>> +config SYS_BOARD
>>> + default "colibri-imx8qxp"
>>> +
>>> +config SYS_VENDOR
>>> + default "toradex"
>>> +
>>> +config SYS_CONFIG_NAME
>>> + default "colibri-imx8qxp"
>>> +
>>> +config TDX_CFG_BLOCK
>>> + default y
>>> +
>>> +config TDX_HAVE_MMC
>>> + default y
>>> +
>>> +config TDX_CFG_BLOCK_DEV
>>> + default "0"
>>> +
>>> +config TDX_CFG_BLOCK_PART
>>> + default "1"
>>> +
>>> +# Toradex config block in eMMC, at the end of 1st "boot sector"
>>> +config TDX_CFG_BLOCK_OFFSET
>>> + default "-512"
>>> +
>>> +source "board/toradex/common/Kconfig"
>>> +
>>> +endif
>>> diff --git a/board/toradex/colibri-imx8qxp/MAINTAINERS
>>> b/board/toradex/colibri-imx8qxp/MAINTAINERS
>>> new file mode 100644
>>> index 0000000000..39a9eb79b7
>>> --- /dev/null
>>> +++ b/board/toradex/colibri-imx8qxp/MAINTAINERS
>>> @@ -0,0 +1,9 @@
>>> +Colibri iMX8QXP
>>> +M: Marcel Ziswiler <marcel.ziswiler at toradex.com>
>>> +W: http://developer.toradex.com/software/linux/linux-software
>>> +S: Maintained
>>> +F: arch/arm/dts/fsl-imx8qxp-colibri.dts
>>> +F: arch/arm/dts/fsl-imx8qxp-colibri-u-boot.dtsi
>>> +F: board/toradex/colibri-imx8qxp/
>>> +F: configs/colibri-imx8qxp_defconfig
>>> +F: include/configs/colibri-imx8qxp.h
>>> diff --git a/board/toradex/colibri-imx8qxp/Makefile
>>> b/board/toradex/colibri-imx8qxp/Makefile
>>> new file mode 100644
>>> index 0000000000..f6342e1dca
>>> --- /dev/null
>>> +++ b/board/toradex/colibri-imx8qxp/Makefile
>>> @@ -0,0 +1,7 @@
>>> +#
>>> +# Copyright 2019 Toradex
>>> +#
>>> +# SPDX-License-Identifier: GPL-2.0+
>>
>> SPDX line should be in the beginning of the file.
>>
>>> +#
>>> +
>>> +obj-y += colibri-imx8qxp.o
>>> diff --git a/board/toradex/colibri-imx8qxp/README
>>> b/board/toradex/colibri-imx8qxp/README
>>> new file mode 100644
>>> index 0000000000..e68d183fe6
>>> --- /dev/null
>>> +++ b/board/toradex/colibri-imx8qxp/README
>>> @@ -0,0 +1,66 @@
>>> +U-Boot for the Toradex Colibri iMX8QXP V1.0B module
>>> +
>>> +Quick Start
>>> +===========
>>> +
>>> +- Build the ARM trusted firmware binary
>>> +- Get scfw_tcm.bin and ahab-container.img
>>> +- Build U-Boot
>>> +- Load U-Boot binary using uuu
>>> +- Flash U-Boot binary into the eMMC
>>> +- Boot
>>> +
>>> +Get and Build the ARM Trusted Firmware
>>> +======================================
>>> +
>>> +$ git clone -b imx_4.14.78_1.0.0_ga
>>> https://source.codeaurora.org/external/imx/imx-atf
>>> +$ cd imx-atf/
>>> +$ make PLAT=imx8qxp bl31
>>> +
>>> +Get scfw_tcm.bin and ahab-container.img
>>> +=======================================
>>> +
>>> +$ wget
>>> https://github.com/toradex/meta-fsl-bsp-release/blob/toradex-sumo-4.14.78-1.0.0_ga-bringup/imx/meta-bsp/recipes-bsp/imx-sc-firmware/files/mx8qx-colibri-scfw-tcm.bin?raw=true
>>> +$ mv mx8qx-colibri-scfw-tcm.bin\?raw\=true mx8qx-colibri-scfw-
>>> tcm.bin
>>> +$ wget
>>> https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-7.6.bin
>>> +$ chmod +x firmware-imx-7.6.bin
>>> +$ ./firmware-imx-7.6.bin
>>> +
>>> +Copy the following binaries to the U-Boot folder:
>>> +
>>> +$ cp imx-atf/build/imx8qxp/release/bl31.bin .
>>> +$ cp u-boot/u-boot.bin .
>>> +
>>> +Copy the following firmware to the U-Boot folder:
>>> +
>>> +$ cp firmware-imx-7.6/firmware/seco/ahab-container.img .
>>> +
>>> +Build U-Boot
>>> +============
>>> +
>>> +$ make colibri-imx8qxp_defconfig
>>> +$ make u-boot-dtb.imx
>>> +
>>> +Load the U-Boot Binary Using UUU
>>> +================================
>>> +
>>> +Get the latest version of the universal update utility (uuu) aka
>>> mfgtools 3.0:
>>> +
>>> +
>>> https://community.nxp.com/external-link.jspa?url=https%3A%2F%2Fgithub.com%2FNXPmicro%2Fmfgtools%2Freleases
>>> +
>>> +Put the module into USB recovery aka serial downloader mode,
>>> connect USB device
>>> +to your host and execute uuu:
>>> +
>>> +sudo ./uuu u-boot/u-boot-dtb.imx
>>> +
>>> +Flash the U-Boot Binary into the eMMC
>>> +=====================================
>>> +
>>> +Burn the u-boot-dtb.imx binary to the primary eMMC hardware boot
>>> area partition:
>>> +
>>> +load mmc 1:1 $loadaddr u-boot-dtb.imx
>>> +setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt ${blkcnt} /
>>> 0x200
>>> +mmc dev 0 1
>>> +mmc write ${loadaddr} 0x0 ${blkcnt}
>>> +
>>> +Boot
>>> diff --git a/board/toradex/colibri-imx8qxp/colibri-imx8qxp.c
>>> b/board/toradex/colibri-imx8qxp/colibri-imx8qxp.c
>>> new file mode 100644
>>> index 0000000000..9aa0f096d2
>>> --- /dev/null
>>> +++ b/board/toradex/colibri-imx8qxp/colibri-imx8qxp.c
>>> @@ -0,0 +1,212 @@
>>> +// SPDX-License-Identifier: GPL-2.0+
>>> +/*
>>> + * Copyright 2019 Toradex
>>> + */
>>> +
>>> +#include <common.h>
>>> +
>>> +#include <asm/arch/clock.h>
>>> +#include <asm/arch/imx8-pins.h>
>>> +#include <asm/arch/iomux.h>
>>> +#include <asm/arch/sci/sci.h>
>>> +#include <asm/arch/sys_proto.h>
>>> +#include <asm/gpio.h>
>>> +#include <asm/io.h>
>>> +#include <asm/mach-imx/video.h>
>>> +#include <dm.h>
>>> +#include <environment.h>
>>> +#include <errno.h>
>>> +#include <fdt_support.h>
>>> +#include <fsl_esdhc.h>
>>> +#include <fsl_ifc.h>
>>> +#include <i2c.h>
>>> +#include <linux/libfdt.h>
>>> +#include <malloc.h>
>>> +#include <netdev.h>
>>> +#include <power-domain.h>
>>> +#include <usb.h>
>>> +
>>> +#include "../common/tdx-cfg-block.h"
>>> +
>>> +DECLARE_GLOBAL_DATA_PTR;
>>> +
>>> +#define GPIO_PAD_CTRL ((SC_PAD_CONFIG_NORMAL <<
>>> PADRING_CONFIG_SHIFT) | \
>>> + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT)
>>> | \
>>> + (SC_PAD_28FDSOI_DSE_DV_HIGH <<
>>> PADRING_DSE_SHIFT) | \
>>> + (SC_PAD_28FDSOI_PS_PU <<
>>> PADRING_PULL_SHIFT))
>>> +
>>> +#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN <<
>>> PADRING_CONFIG_SHIFT) | \
>>> + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT)
>>> | \
>>> + (SC_PAD_28FDSOI_DSE_DV_HIGH <<
>>> PADRING_DSE_SHIFT) | \
>>> + (SC_PAD_28FDSOI_PS_PU <<
>>> PADRING_PULL_SHIFT))
>>> +
>>> +static iomux_cfg_t uart3_pads[] = {
>>> + SC_P_FLEXCAN2_RX | MUX_MODE_ALT(2) |
>>> MUX_PAD_CTRL(UART_PAD_CTRL),
>>> + SC_P_FLEXCAN2_TX | MUX_MODE_ALT(2) |
>>> MUX_PAD_CTRL(UART_PAD_CTRL),
>>> + /* Transceiver FORCEOFF# signal, mux to use pullup */
>>> + SC_P_QSPI0B_DQS | MUX_MODE_ALT(4) |
>>> MUX_PAD_CTRL(UART_PAD_CTRL),
>>> +};
>>> +
>>> +static void setup_iomux_uart(void)
>>> +{
>>> + imx8_iomux_setup_multiple_pads(uart3_pads,
>>> ARRAY_SIZE(uart3_pads));
>>> +}
>>> +
>>> +int board_early_init_f(void)
>>> +{
>>> + sc_pm_clock_rate_t rate;
>>> + sc_err_t err = 0;
>>> +
>>> + /*
>>> + * This works around that having only UART3 up the baudrate
>>> is 1.2M
>>> + * instead of 115.2k. Set UART0 clock root to 80 MHz
>>> + */
>>> + rate = 80000000;
>>> + err = sc_pm_set_clock_rate(-1, SC_R_UART_0, SC_PM_CLK_PER,
>>> &rate);
>>> + if (err != SC_ERR_NONE)
>>> + return 0;
>>> +
>>> + /* Power up UART3 */
>>> + err = sc_pm_set_resource_power_mode(-1, SC_R_UART_3,
>>> SC_PM_PW_MODE_ON);
>>> + if (err != SC_ERR_NONE)
>>> + return 0;
>>> +
>>> + /* Set UART3 clock root to 80 MHz */
>>> + rate = 80000000;
>>> + err = sc_pm_set_clock_rate(-1, SC_R_UART_3, SC_PM_CLK_PER,
>>> &rate);
>>> + if (err != SC_ERR_NONE)
>>> + return 0;
>>> +
>>> + /* Enable UART3 clock root */
>>> + err = sc_pm_clock_enable(-1, SC_R_UART_3, SC_PM_CLK_PER,
>>> true, false);
>>> + if (err != SC_ERR_NONE)
>>> + return 0;
>>> +
>>> + setup_iomux_uart();
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +#undef CONFIG_MXC_GPIO /* TODO */
>>> +#ifdef CONFIG_MXC_GPIO
>>> +#define IOEXP_RESET IMX_GPIO_NR(1, 1)
>>> +
>>> +static iomux_cfg_t board_gpios[] = {
>>> + SC_P_SPI2_SDO | MUX_MODE_ALT(4) |
>>> MUX_PAD_CTRL(GPIO_PAD_CTRL),
>>> + SC_P_ENET0_REFCLK_125M_25M | MUX_MODE_ALT(4) | \
>>> + MUX_PAD_CTRL(GPIO_PAD_CTRL),
>>> +};
>>> +
>>> +static void board_gpio_init(void)
>>> +{
>>> + struct gpio_desc desc;
>>> + int ret;
>>> +
>>> + ret = dm_gpio_lookup_name("gpio at 1a_3", &desc);
>>> + if (ret)
>>> + return;
>>> +
>>> + ret = dm_gpio_request(&desc, "bb_per_rst_b");
>>> + if (ret)
>>> + return;
>>> +
>>> + dm_gpio_set_dir_flags(&desc, GPIOD_IS_OUT);
>>> + dm_gpio_set_value(&desc, 0);
>>> + udelay(50);
>>> + dm_gpio_set_value(&desc, 1);
>>> +
>>> + imx8_iomux_setup_multiple_pads(board_gpios,
>>> ARRAY_SIZE(board_gpios));
>>> +
>>> + /* enable i2c port expander assert reset line */
>>> + gpio_request(IOEXP_RESET, "ioexp_rst");
>>> + gpio_direction_output(IOEXP_RESET, 1);
>>> +}
>>> +#else
>>> +static inline void board_gpio_init(void) {}
>>> +#endif
>>> +
>>> +#if IS_ENABLED(CONFIG_FEC_MXC)
>>> +#include <miiphy.h>
>>> +
>>> +int board_phy_config(struct phy_device *phydev)
>>> +{
>>> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
>>> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
>>> +
>>> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00);
>>> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
>>> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
>>> + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
>>> +
>>> + if (phydev->drv->config)
>>> + phydev->drv->config(phydev);
>>> +
>>> + return 0;
>>> +}
>>> +#endif
>>> +
>>> +void build_info(void)
>>> +{
>>> + u32 sc_build = 0, sc_commit = 0;
>>> +
>>> + /* Get SCFW build and commit id */
>>> + sc_misc_build_info(-1, &sc_build, &sc_commit);
>>> + if (!sc_build) {
>>> + printf("SCFW does not support build info\n");
>>> + sc_commit = 0; /* Display 0 if build info not
>>> supported */
>>> + }
>>> + printf("Build: SCFW %x\n", sc_commit);
>>> +}
>>> +
>>> +int checkboard(void)
>>> +{
>>> + puts("Model: Toradex Colibri iMX8X\n");
>>> +
>>> + build_info();
>>> + print_bootinfo();
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +int board_init(void)
>>> +{
>>> + board_gpio_init();
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +void detail_board_ddr_info(void)
>>> +{
>>> + puts("\nDDR ");
>>> +}
>>> +
>>> +/*
>>> + * Board specific reset that is system reset.
>>> + */
>>> +void reset_cpu(ulong addr)
>>> +{
>>> + /* TODO */
>>> +}
>>> +
>>> +#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
>>> +int ft_board_setup(void *blob, bd_t *bd)
>>> +{
>>> + return ft_common_board_setup(blob, bd);
>>> +}
>>> +#endif
>>> +
>>> +int board_mmc_get_env_dev(int devno)
>>> +{
>>> + return devno;
>>> +}
>>> +
>>> +int board_late_init(void)
>>> +{
>>> +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
>>> +/* TODO move to common */
>>> + env_set("board_name", "Colibri iMX8QXP");
>>> + env_set("board_rev", "v1.0");
>>> +#endif
>>> +
>>> + return 0;
>>> +}
>>> diff --git a/board/toradex/colibri-imx8qxp/imximage.cfg
>>> b/board/toradex/colibri-imx8qxp/imximage.cfg
>>> new file mode 100644
>>> index 0000000000..ce9e66c64d
>>> --- /dev/null
>>> +++ b/board/toradex/colibri-imx8qxp/imximage.cfg
>>> @@ -0,0 +1,24 @@
>>> +/* SPDX-License-Identifier: GPL-2.0+ */
>>> +/*
>>> + * Copyright 2019 Toradex
>>> + *
>>> + * Refer doc/README.imx8image for more details about how-to
>>> configure
>>> + * and create imx8image boot image
>>> + */
>>> +
>>> +#define __ASSEMBLY__
>>> +
>>> +/* Boot from SD, sector size 0x400 */
>>> +BOOT_FROM EMMC_FASTBOOT 0x400
>>> +/* SoC type IMX8QX */
>>> +SOC_TYPE IMX8QX
>>> +/* Append seco container image */
>>> +APPEND ahab-container.img
>>> +/* Create the 2nd container */
>>> +CONTAINER
>>> +/* Add scfw image with exec attribute */
>>> +IMAGE SCU mx8qx-colibri-scfw-tcm.bin
>>> +/* Add ATF image with exec attribute */
>>> +IMAGE A35 bl31.bin 0x80000000
>>> +/* Add U-Boot image with load attribute */
>>> +DATA A35 u-boot-dtb.bin 0x80020000
>>> diff --git a/configs/colibri-imx8qxp_defconfig b/configs/colibri-
>>> imx8qxp_defconfig
>>> new file mode 100644
>>> index 0000000000..d697546ed7
>>> --- /dev/null
>>> +++ b/configs/colibri-imx8qxp_defconfig
>>> @@ -0,0 +1,53 @@
>>> +CONFIG_ARM=y
>>> +CONFIG_ARCH_IMX8=y
>>> +CONFIG_SYS_TEXT_BASE=0x80020000
>>> +CONFIG_SYS_MALLOC_F_LEN=0x2000
>>> +CONFIG_TARGET_COLIBRI_IMX8QXP=y
>>> +CONFIG_DISTRO_DEFAULTS=y
>>> +CONFIG_NR_DRAM_BANKS=3
>>> +CONFIG_FIT=y
>>> +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/toradex/colibri-
>>> imx8qxp/imximage.cfg"
>>> +CONFIG_LOG=y
>>> +CONFIG_VERSION_VARIABLE=y
>>> +# CONFIG_DISPLAY_BOARDINFO is not set
>>> +CONFIG_BOARD_EARLY_INIT_F=y
>>> +CONFIG_CMD_CPU=y
>>> +# CONFIG_CMD_IMPORTENV is not set
>>> +CONFIG_CMD_MEMTEST=y
>>> +CONFIG_CMD_CLK=y
>>> +CONFIG_CMD_DM=y
>>> +CONFIG_CMD_GPIO=y
>>> +CONFIG_CMD_I2C=y
>>> +CONFIG_CMD_MMC=y
>>> +CONFIG_CMD_CACHE=y
>>> +CONFIG_CMD_UUID=y
>>> +CONFIG_CMD_EXT4_WRITE=y
>>> +CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8qxp-colibri"
>>> +CONFIG_ENV_IS_IN_MMC=y
>>> +CONFIG_CLK_IMX8=y
>>> +CONFIG_CPU=y
>>> +CONFIG_DM_GPIO=y
>>> +CONFIG_MXC_GPIO=y
>>> +CONFIG_DM_I2C=y
>>> +CONFIG_SYS_I2C_IMX_LPI2C=y
>>> +CONFIG_MISC=y
>>> +CONFIG_DM_MMC=y
>>> +CONFIG_PHYLIB=y
>>> +CONFIG_PHY_ADDR_ENABLE=y
>>> +CONFIG_PHY_MICREL=y
>>> +CONFIG_DM_ETH=y
>>> +CONFIG_FEC_MXC_SHARE_MDIO=y
>>> +CONFIG_FEC_MXC_MDIO_BASE=0x5B040000
>>> +CONFIG_FEC_MXC=y
>>> +CONFIG_MII=y
>>> +CONFIG_PINCTRL=y
>>> +CONFIG_PINCTRL_IMX8=y
>>> +CONFIG_POWER_DOMAIN=y
>>> +CONFIG_IMX8_POWER_DOMAIN=y
>>> +CONFIG_DM_REGULATOR=y
>>> +CONFIG_DM_REGULATOR_FIXED=y
>>> +CONFIG_DM_REGULATOR_GPIO=y
>>> +CONFIG_DM_SERIAL=y
>>> +CONFIG_FSL_LPUART=y
>>> +CONFIG_DM_THERMAL=y
>>> +# CONFIG_EFI_LOADER is not set
>>> diff --git a/include/configs/colibri-imx8qxp.h
>>> b/include/configs/colibri-imx8qxp.h
>>> new file mode 100644
>>> index 0000000000..33cbcb44a9
>>> --- /dev/null
>>> +++ b/include/configs/colibri-imx8qxp.h
>>> @@ -0,0 +1,214 @@
>>> +/* SPDX-License-Identifier: GPL-2.0+ */
>>> +/*
>>> + * Copyright 2019 Toradex
>>> + */
>>> +
>>> +#ifndef __COLIBRI_IMX8QXP_H
>>> +#define __COLIBRI_IMX8QXP_H
>>> +
>>> +#include <asm/arch/imx-regs.h>
>>> +#include <linux/sizes.h>
>>> +
>>> +#define CONFIG_REMAKE_ELF
>>> +
>>> +#define CONFIG_DISPLAY_BOARDINFO_LATE
>>> +
>>> +#undef CONFIG_CMD_EXPORTENV
>>> +#undef CONFIG_CMD_IMPORTENV
>>> +#undef CONFIG_CMD_IMLS
>>> +
>>> +#undef CONFIG_CMD_CRC32
>>> +#undef CONFIG_BOOTM_NETBSD
>>> +
>>> +#define CONFIG_FSL_ESDHC
>>> +#define CONFIG_FSL_USDHC
>>> +#define CONFIG_SYS_FSL_ESDHC_ADDR 0
>>> +#define USDHC1_BASE_ADDR 0x5B010000
>>> +#define USDHC2_BASE_ADDR 0x5B020000
>>> +#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
>>> +
>>> +#define CONFIG_ENV_OVERWRITE
>>> +
>>> +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
>>> +
>>> +#define FEC_QUIRK_ENET_MAC
>>> +
>>> +#define CONFIG_IP_DEFRAG
>>> +#define CONFIG_TFTP_BLOCKSIZE 4096
>>
>> 4096 can be replaced with SZ_4K (from include/linux/sizes.h)
>>
>>> +#define CONFIG_TFTP_TSIZE
>>> +
>>> +#define CONFIG_IPADDR 192.168.10.2
>>> +#define CONFIG_NETMASK 255.255.255.0
>>> +#define CONFIG_SERVERIP 192.168.10.1
>>> +
>>> +#define MEM_LAYOUT_ENV_SETTINGS \
>>> + "fdt_addr_r=0x84000000\0" \
>>> + "kernel_addr_r=0x82000000\0" \
>>> + "ramdisk_addr_r=0x84100000\0"
>>> +
>>> +#ifdef CONFIG_AHAB_BOOT
>>> +#define AHAB_ENV "sec_boot=yes\0"
>>> +#else
>>> +#define AHAB_ENV "sec_boot=no\0"
>>> +#endif
>>> +
>>> +/* Boot M4 */
>>> +#define M4_BOOT_ENV \
>>> + "m4_0_image=m4_0.bin\0" \
>>> + "loadm4image_0=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr}
>>> " \
>>> + "${m4_0_image}\0" \
>>> + "m4boot_0=run loadm4image_0; dcache flush; bootaux
>>> ${loadaddr} 0\0" \
>>> +
>>> +#define MFG_NAND_PARTITION ""
>>> +
>>> +#define BOOT_TARGET_DEVICES(func) \
>>> + func(MMC, mmc, 0) \
>>> + func(MMC, mmc, 1) \
>>> + func(DHCP, dhcp, na)
>>> +#include <config_distro_bootcmd.h>
>>> +#undef BOOTENV_RUN_NET_USB_START
>>> +#define BOOTENV_RUN_NET_USB_START ""
>>> +
>>> +#define CONFIG_MFG_ENV_SETTINGS \
>>> + "mfgtool_args=setenv bootargs
>>> console=${console},${baudrate} " \
>>> + "rdinit=/linuxrc g_mass_storage.stall=0 " \
>>> + "g_mass_storage.removable=1
>>> g_mass_storage.idVendor=0x066F " \
>>> + "g_mass_storage.idProduct=0x37FF " \
>>> + "g_mass_storage.iSerialNumber=\"\" "\
>>> + MFG_NAND_PARTITION \
>>> + "video=imxdpufb5:off video=imxdpufb6:off
>>> video=imxdpufb7:off " \
>>> + "clk_ignore_unused "\
>>> + "\0" \
>>> + "initrd_addr=0x83800000\0" \
>>> + "initrd_high=0xffffffff\0" \
>>> + "bootcmd_mfg=run mfgtool_args;booti ${loadaddr}
>>> ${initrd_addr} " \
>>> + "${fdt_addr};\0" \
>>> +
>>> +/* Initial environment variables */
>>> +#define CONFIG_EXTRA_ENV_SETTINGS \
>>> + AHAB_ENV \
>>> + BOOTENV \
>>> + CONFIG_MFG_ENV_SETTINGS \
>>> + M4_BOOT_ENV \
>>> + MEM_LAYOUT_ENV_SETTINGS \
>>> + "boot_fdt=try\0" \
>>> + "bootscript=echo Running bootscript from mmc ...; source\0"
>>> \
>>> + "console=ttyLP3,115200
>>> earlycon=lpuart32,0x5a090000,115200\0" \
>>> + "fdt_addr=0x83000000\0" \
>>> + "fdt_file=fsl-imx8qxp-colibri-eval-v3.dtb\0" \
>>> + "fdt_high=0xffffffffffffffff\0" \
>>> + "finduuid=part uuid mmc ${mmcdev}:2 uuid\0" \
>>> + "image=Image\0" \
>>> + "initrd_addr=0x83800000\0" \
>>> + "initrd_high=0xffffffffffffffff\0" \
>>> + "loadbootscript=fatload mmc ${mmcdev}:${mmcpart}
>>> ${loadaddr} " \
>>> + "${script};\0" \
>>> + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr}
>>> ${fdt_file}\0" \
>>> + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr}
>>> ${image}\0" \
>>> + "mmcargs=setenv bootargs console=${console},${baudrate} " \
>>> + "root=PARTUUID=${uuid} rootwait " \
>>> + "mmcautodetect=yes\0" \
>>> + "mmcboot=echo Booting from mmc ...; " \
>>> + "run finduuid; run mmcargs; " \
>>> + "if test ${boot_fdt} = yes || test ${boot_fdt} =
>>> try; then " \
>>> + "if run loadfdt; then " \
>>> + "booti ${loadaddr} - ${fdt_addr}; "
>>> \
>>> + "else " \
>>> + "echo WARN: Cannot load the DT; " \
>>> + "fi; " \
>>> + "else " \
>>> + "echo wait for boot; " \
>>> + "fi;\0" \
>>> + "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
>>> + "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
>>> + "netargs=setenv bootargs console=${console} root=/dev/nfs
>>> ip=dhcp " \
>>> + "nfsroot=${serverip}:${nfsroot},v3,tcp
>>> video=imxdpufb5:off " \
>>> + "video=imxdpufb6:off video=imxdpufb7:off\0" \
>>> + "netboot=echo Booting from net ...; " \
>>> + "run netargs; " \
>>> + "if test ${ip_dyn} = yes; then " \
>>> + "setenv get_cmd dhcp; " \
>>> + "else " \
>>> + "setenv get_cmd tftp; " \
>>> + "fi; " \
>>> + "${get_cmd} ${loadaddr} ${image}; " \
>>> + "if test ${boot_fdt} = yes || test ${boot_fdt} =
>>> try; then " \
>>> + "if ${get_cmd} ${fdt_addr} ${fdt_file};
>>> then " \
>>> + "booti ${loadaddr} - ${fdt_addr}; "
>>> \
>>> + "else " \
>>> + "echo WARN: Cannot load the DT; " \
>>> + "fi; " \
>>> + "else " \
>>> + "booti; " \
>>> + "fi;\0" \
>>> + "nfsboot=run netargs; dhcp ${loadaddr} ${image}; tftp
>>> ${fdt_addr} " \
>>> + "colibri-imx8qxp/${fdt_file}; booti ${loadaddr} - "
>>> \
>>> + "${fdt_addr}\0" \
>>> + "panel=NULL\0" \
>>> + "script=boot.scr\0" \
>>> + "video=imxdpufb5:off video=imxdpufb6:off
>>> video=imxdpufb7:off\0"
>>> +
>>> +#undef CONFIG_BOOTCOMMAND
>>> +#define CONFIG_BOOTCOMMAND \
>>> + "mmc dev ${mmcdev}; if mmc rescan; then " \
>>> + "if run loadbootscript; then " \
>>> + "run bootscript; " \
>>> + "else " \
>>> + "if run loadimage; then " \
>>> + "run mmcboot; " \
>>> + "else run netboot; " \
>>> + "fi; " \
>>> + "fi; " \
>>> + "else booti ${loadaddr} - ${fdt_addr}; fi"
>>> +
>>> +/* Link Definitions */
>>> +#define CONFIG_LOADADDR 0x80280000
>>> +
>>> +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
>>> +
>>> +#define CONFIG_SYS_INIT_SP_ADDR 0x80200000
>>> +
>>> +#define CONFIG_SYS_MEMTEST_START 0x88000000
>>> +#define CONFIG_SYS_MEMTEST_END 0x89000000
>>> +
>>> +/* Environment in eMMC, before config block at the end of 1st
>>> "boot sector" */
>>> +#define CONFIG_ENV_SIZE (8 * 1024)
>>
>> (8 * 1024) can be replaced with SZ_8K (from include/linux/sizes.h)
>>
>>> +#define CONFIG_ENV_OFFSET (-CONFIG_ENV_SIZE + \
>>> + CONFIG_TDX_CFG_BLOCK_OFFSE
>>> T)
>>> +#define CONFIG_SYS_MMC_ENV_DEV 0
>>> +#define CONFIG_SYS_MMC_ENV_PART 1
>>> +
>>> +#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
>>> +
>>> +/* On Colibri iMX8 USDHC1 is eMMC, USDHC2 is 4-bit SD */
>>> +#define CONFIG_SYS_MMC_ENV_DEV 0 /* USDHC1
>>> eMMC */
>>> +#define CONFIG_SYS_FSL_USDHC_NUM 2
>>> +
>>> +/* Size of malloc() pool */
>>> +#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (32 *
>>> 1024)) * 1024)
>>> +
>>> +#define CONFIG_SYS_SDRAM_BASE 0x80000000
>>> +#define CONFIG_NR_DRAM_BANKS 3
>>> +#define PHYS_SDRAM_1 0x80000000
>>> +#define PHYS_SDRAM_2 0x880000000
>>> +#define PHYS_SDRAM_1_SIZE 0x80000000 /* 2 GB */
>> 0x80000000 can be replaced with SZ_2G (from include/linux/sizes.h)
>>> +#define PHYS_SDRAM_2_SIZE 0x00000000 /* 0 GB */
>>> +
>>> +/* Serial */
>>> +#define CONFIG_BAUDRATE 115200
>>> +
>>> +/* Monitor Command Prompt */
>>> +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
>>> +#define CONFIG_SYS_CBSIZE 2048
>>
>> Same as above
>>
>>> +#define CONFIG_SYS_MAXARGS 64
>>> +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
>>> +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
>>> + sizeof(CONFIG_SYS_PROMPT) +
>>> 16)
>>> +
>>> +/* Generic Timer Definitions */
>>> +#define COUNTER_FREQUENCY 8000000 /* 8MHz */
>>> +
>>> +#define BOOTAUX_RESERVED_MEM_BASE 0x88000000
>>> +#define BOOTAUX_RESERVED_MEM_SIZE 0x08000000 /* Reserve from
>>> second 128MB */
>> Same as above
>>> +
>>> +#endif /* __COLIBRI_IMX8QXP_H */
>>> --
>>> 2.20.1
>>>
>>> _______________________________________________
>>> U-Boot mailing list
>>> U-Boot at lists.denx.de
>>> https://lists.denx.de/listinfo/u-boot
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
More information about the U-Boot
mailing list