[U-Boot] [PATCH] arm: dts: sync dts for Allwinner H6
Clément Péron
peron.clem at gmail.com
Wed Aug 14 21:15:45 UTC 2019
Hi
On Sun, 11 Aug 2019 at 22:42, Clément Péron <peron.clem at gmail.com> wrote:
>
> Sync Kernel DTS for Allwinner H6 boards.
>
> commit <d45331b00ddb> Linux 5.3-rc4
>
> Signed-off-by: Clément Péron <peron.clem at gmail.com>
> ---
> arch/arm/dts/sun50i-h6-beelink-gs1.dts | 76 ++++++++++++++++++++++++++
> arch/arm/dts/sun50i-h6-pine-h64.dts | 12 ++++
> arch/arm/dts/sun50i-h6.dtsi | 43 ++++++++++++++-
> 3 files changed, 128 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/dts/sun50i-h6-beelink-gs1.dts b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
> index 54b0882bed..0dc33c90dd 100644
> --- a/arch/arm/dts/sun50i-h6-beelink-gs1.dts
> +++ b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
> @@ -14,6 +14,7 @@
> compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
>
> aliases {
> + ethernet0 = &emac;
> serial0 = &uart0;
> };
>
> @@ -21,6 +22,17 @@
> stdout-path = "serial0:115200n8";
> };
>
> + connector {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> leds {
> compatible = "gpio-leds";
>
> @@ -41,6 +53,40 @@
> };
> };
>
> +&de {
> + status = "okay";
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&emac {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ext_rgmii_pins>;
> + phy-mode = "rgmii";
> + phy-handle = <&ext_rgmii_phy>;
> + phy-supply = <®_aldo2>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + status = "okay";
> +};
> +
> +&hdmi_out {
> + hdmi_out_con: endpoint {
> + remote-endpoint = <&hdmi_con_in>;
> + };
> +};
> +
> +&mdio {
> + ext_rgmii_phy: ethernet-phy at 1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + };
> +};
> +
> &mmc0 {
> vmmc-supply = <®_cldo1>;
> cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> @@ -57,6 +103,15 @@
> status = "okay";
> };
>
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&pio {
> + vcc-pd-supply = <®_cldo1>;
> + vcc-pg-supply = <®_aldo1>;
> +};
> +
> &r_i2c {
> status = "okay";
>
> @@ -177,8 +232,29 @@
> };
> };
>
> +&r_pio {
> + /*
> + * PL0 and PL1 are used for PMIC I2C
> + * don't enable the pl-supply else
> + * it will fail at boot
> + *
> + * vcc-pl-supply = <®_aldo1>;
> + */
> + vcc-pm-supply = <®_aldo1>;
> +};
> +
> &uart0 {
> pinctrl-names = "default";
> pinctrl-0 = <&uart0_ph_pins>;
> status = "okay";
> };
> +
> +&usb2otg {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usb2phy {
> + usb0_vbus-supply = <®_vcc5v>;
> + status = "okay";
> +};
> diff --git a/arch/arm/dts/sun50i-h6-pine-h64.dts b/arch/arm/dts/sun50i-h6-pine-h64.dts
> index 4802902e12..1898345183 100644
> --- a/arch/arm/dts/sun50i-h6-pine-h64.dts
> +++ b/arch/arm/dts/sun50i-h6-pine-h64.dts
> @@ -127,6 +127,12 @@
> status = "okay";
> };
>
> +&pio {
> + vcc-pc-supply = <®_bldo2>;
> + vcc-pd-supply = <®_cldo1>;
> + vcc-pg-supply = <®_aldo1>;
> +};
> +
> &r_i2c {
> status = "okay";
>
> @@ -243,10 +249,16 @@
> pcf8563: rtc at 51 {
> compatible = "nxp,pcf8563";
> reg = <0x51>;
> + interrupt-parent = <&r_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> #clock-cells = <0>;
> };
> };
>
> +&r_pio {
> + vcc-pm-supply = <®_aldo1>;
> +};
> +
> &uart0 {
> pinctrl-names = "default";
> pinctrl-0 = <&uart0_ph_pins>;
> diff --git a/arch/arm/dts/sun50i-h6.dtsi b/arch/arm/dts/sun50i-h6.dtsi
> index e0dc4a05c1..7628a7c830 100644
> --- a/arch/arm/dts/sun50i-h6.dtsi
> +++ b/arch/arm/dts/sun50i-h6.dtsi
> @@ -101,7 +101,7 @@
> #size-cells = <1>;
> ranges;
>
> - display-engine at 1000000 {
> + bus at 1000000 {
> compatible = "allwinner,sun50i-h6-de3",
> "allwinner,sun50i-a64-de2";
> reg = <0x1000000 0x400000>;
> @@ -203,11 +203,32 @@
> #reset-cells = <1>;
> };
>
> + dma: dma-controller at 3002000 {
> + compatible = "allwinner,sun50i-h6-dma";
> + reg = <0x03002000 0x1000>;
> + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
> + clock-names = "bus", "mbus";
> + dma-channels = <16>;
> + dma-requests = <46>;
> + resets = <&ccu RST_BUS_DMA>;
> + #dma-cells = <1>;
> + };
> +
> sid: sid at 3006000 {
> compatible = "allwinner,sun50i-h6-sid";
> reg = <0x03006000 0x400>;
> };
>
> + watchdog: watchdog at 30090a0 {
> + compatible = "allwinner,sun50i-h6-wdt",
> + "allwinner,sun6i-a31-wdt";
> + reg = <0x030090a0 0x20>;
> + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> + /* Broken on some H6 boards */
> + status = "disabled";
> + };
> +
> pio: pinctrl at 300b000 {
> compatible = "allwinner,sun50i-h6-pinctrl";
> reg = <0x0300b000 0x400>;
> @@ -243,6 +264,15 @@
> bias-pull-up;
> };
>
> + /omit-if-no-ref/
Avoid this patch the /omit-if-no-ref/ can't be interpreted on U-boot.
Regards,
Clément
> + mmc1_pins: mmc1-pins {
> + pins = "PG0", "PG1", "PG2", "PG3",
> + "PG4", "PG5";
> + function = "mmc1";
> + drive-strength = <30>;
> + bias-pull-up;
> + };
> +
> mmc2_pins: mmc2-pins {
> pins = "PC1", "PC4", "PC5", "PC6",
> "PC7", "PC8", "PC9", "PC10",
> @@ -294,6 +324,8 @@
> resets = <&ccu RST_BUS_MMC1>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;
> status = "disabled";
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -445,7 +477,6 @@
> resets = <&ccu RST_BUS_OHCI3>,
> <&ccu RST_BUS_EHCI3>;
> phys = <&usb2phy 3>;
> - phy-names = "usb";
> status = "disabled";
> };
>
> @@ -457,7 +488,6 @@
> <&ccu CLK_USB_OHCI3>;
> resets = <&ccu RST_BUS_OHCI3>;
> phys = <&usb2phy 3>;
> - phy-names = "usb";
> status = "disabled";
> };
>
> @@ -613,6 +643,13 @@
> #reset-cells = <1>;
> };
>
> + r_watchdog: watchdog at 7020400 {
> + compatible = "allwinner,sun50i-h6-wdt",
> + "allwinner,sun6i-a31-wdt";
> + reg = <0x07020400 0x20>;
> + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> r_intc: interrupt-controller at 7021000 {
> compatible = "allwinner,sun50i-h6-r-intc",
> "allwinner,sun6i-a31-r-intc";
> --
> 2.20.1
>
More information about the U-Boot
mailing list