[U-Boot] Rockpro64_V2.1 2018-07-02 Boot Freeze

[Kurt Miller]

On Mon, 2019-08-19 at 15:31 +0200, Mark Kettenis wrote:
> > 
> > From: Jagan Teki <jagan at amarulasolutions.com>
> > Date: Mon, 19 Aug 2019 00:21:40 +0530
> > 
> > + Kever
> > 
> > On Sun, Aug 18, 2019 at 1:21 AM Kurt Miller <lists at intricatesoftware.com> wrote:
> > > 
> > > 
> > > Hello,
> > > 
> > > The Rockpro64_V2.1 2018-07-02 using master code base freezes
> > > with only the following output:
> > > 
> > > U-Boot TPL 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31)
> > > 
> > > Whereas another board dated 2018-06-06 works and outputs the following:
> > > 
> > > U-Boot TPL 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31)
> > > Trying to boot from BOOTROM
> > > Returning to boot ROM...
> > > 
> > > U-Boot SPL 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31 +0200)
> > > 
> > > Both board have 4G RAM.
> > > 
> > > U-Boot was built by Mark Kettenis from master with only the
> > > baud rate changed for both tests. The 2018-07-02 board has different
> > > markings for the CPU and the RAM as follows:
> > > 
> > >      2018-06-06       2018-07-02
> > > CPU: RK3399           RK3399
> > >      SBETMF976 1652   SBETNM271 1826
> > > 
> > > RAM: PS006-075 BT     PS052-053 BT
> > >      N1YJ             83RL
> > > 
> > > Please let me know if there is additional information needed to
> > > further diagnose the boot freeze.
> > Please use mainline, and with doc/README.rockchip instructions.
> This is mainline as of Aug 16.  I built the image for Kurt and it the
> same binaries (one for TPL+SPL one for U-Boot+ATF) works fine on my
> board.
> 
> > 
> > I'm able to boot with mainline tree.
> Sure I can believe that.  I believe your board from the same batch as
> mine.  I suspect that the DRAM used on Kurt's board may require
> slightly different timings.
> 

While my board (2018-07-02) freezes with Aug 16 mainline TPL,
it does boot ok with the rockchip-linux TPL with the following
output which may have some useful info:

DDR Version 1.23 20190709                                                    
In                                                                           
channel 0                                                                    
CS = 0                                                                       
MR0=0xB8                                                                     
MR4=0x1                                 
MR5=0xFF                                
MR8=0x10                                
MR12=0x72                               
MR14=0x72                               
MR18=0x0                                
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0xB8
MR4=0x1
MR5=0xFF
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
change freq to 416MHz 0,1
Channel 0: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB
Channel 1: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB
256B stride
channel 0
CS = 0
MR0=0xB8
MR4=0x1
MR5=0xFF
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0xB8
MR4=0x1
MR5=0xFF
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
channel 0, cs 0, advanced training done
channel 1, cs 0, advanced training done
change freq to 856MHz 1,0
ch 0 ddrconfig = 0x101, ddrsize = 0x40
ch 1 ddrconfig = 0x101, ddrsize = 0x40
pmugrf_os_reg[2] = 0x32C1F2C1, stride = 0xD
OUT