[U-Boot] Rockpro64_V2.1 2018-07-02 Boot Freeze

[Kurt Miller]

On Mon, 2019-08-19 at 22:11 +0530, Jagan Teki wrote:
> On Mon, Aug 19, 2019 at 8:42 PM Kurt Miller <lists at intricatesoftware.com> wrote:
> > 
> > 
> > Hi Michael,
> > 
> > On Mon, 2019-08-19 at 16:06 +0200, Michael Nazzareno Trimarchi wrote:
> > > 
> > > It's possible to dump the register after training in mainline uboot?
> > I'm working on getting master to build now. How would I
> > go about dumping the register after training?
> It would be a bit hard, I tried below sequence at the end of
> sdram_init (sorry for direct copy)
> 
>         printf("cic: ctr10: (0x%x - 0x%x)\n", &dram->cic->cic_ctrl0,
> readl(&dram->cic->cic_ctrl0));
>         printf("cic: status0: (0x%x - 0x%x)\n",
> &dram->cic->cic_status0, readl(&dram->cic->cic_status0));
>         printf("grf: ddrc0_con0 (0x%x - 0x%x)\n",
> &dram->grf->ddrc0_con0, readl(&dram->grf->ddrc0_con0));
>         printf("grf: ddrc1_con0 (0x%x - 0x%x)\n",
> &dram->grf->ddrc1_con0, readl(&dram->grf->ddrc1_con0));
>         printf("grf: soc_con0 (0x%x - 0x%x)\n", &dram->grf->soc_con0,
> readl(&dram->grf->soc_con0));
>         printf("pmu: noc_auto_ena (0x%x - 0x%x)\n",
> &dram->pmu->pmu_noc_auto_ena, readl(&dram->pmu->pmu_noc_auto_ena));
>         printf("pmu: bus_idle_req (0x%x - 0x%x)\n",
> &dram->pmu->pmu_bus_idle_req, readl(&dram->pmu->pmu_bus_idle_req));
>         printf("pmu: bus_idle_st (0x%x - 0x%x)\n",
> &dram->pmu->pmu_bus_idle_st, readl(&dram->pmu->pmu_bus_idle_st));
>         printf("pmugrf: os_reg2 (0x%x - 0x%x)\n",
> &dram->pmugrf->os_reg2, readl(&dram->pmugrf->os_reg2));
>         printf("pmugrf: os_reg3 (0x%x - 0x%x)\n",
> &dram->pmugrf->os_reg3, readl(&dram->pmugrf->os_reg3));
>         printf("pmusgrf: soc_con4 (0x%x - 0x%x)\n",
> &dram->pmusgrf->soc_con4, readl(&dram->pmusgrf->soc_con4));

Thank you. I have built mainline with CONFIG_RAM_ROCKCHIP_DEBUG=y
with your printf's above and it outputs the following before freezing:

U-Boot TPL 2019.10-rc2-00016-g81fed78c0a-dirty (Aug 19 2019 - 12:57:39)      
LPDDR4, 50MHz                                                                
BW=32 Col=10 Bk=8 CS0 Row=15 CS=1 Die BW=16 Size=1024MB                      
LPDDR4, 50MHz                                                                
BW=32 Col=10 Bk=8 CS0 Row=15 CS=1 Die BW=16 Size=1024MB
256B stride                             
cic: ctr10: (0xff620000 - 0x14)         
cic: status0: (0xff620010 - 0x101)      
grf: ddrc0_con0 (0xff77e380 - 0x1f81)   
grf: ddrc1_con0 (0xff77e388 - 0x1f81)   
grf: soc_con0 (0xff77e200 - 0x7)
pmu: noc_auto_ena (0xff3100d8 - 0x0)
pmu: bus_idle_req (0xff310060 - 0x0)
pmu: bus_idle_st (0xff310064 - 0x0)
pmugrf: os_reg2 (0xff320308 - 0x32a1f2a1)
pmugrf: os_reg3 (0xff32030c - 0x20000005)
pmusgrf: soc_con4 (0xff33e010 - 0x2600)

Note that 'Size=1024MB' is incorrect. With 'rockchip-linux' TPL
I see 'Size=2048MB'.

Regards,
-Kurt